Search Documents

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By William E. Wallace, S. J. Page, B. L. Razzaboni, C. A. Hill, Pamela Mike, P. Bolsaitis, M. J. Keane, Val Vallyathan

"Respirable quartz cytotoxicity, as measured by erythrocyte hemolysis and pulmonary macrophage release of lactate dehydrogenase in vitro, is neutralized by boiling in water in glass test tubes for 10 to 40 minutes. The cytotoxicity is reduced to near zero by boiling l to IO mg quartz per milliliter water. For greater concentrations of quartz in water the hemolytic potential after 40 minutes of boiling approaches that of native quartz. Replacing the medium with fresh water midway through boiling results in full detoxification through 20 mg quartz per milliliter water. Pre-boiling the medium with silica reduces the detoxification effect. Detoxification persists after mild drying at l 10°C for 8 hours, and persists after three days of resuspension in water at room temperature.INTRODCJCTIONResearch underway to determine interactions of quartz and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages were suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosmal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121°C with no liquid water but with steam present. 1.2 However detoxification under boiling conditions has been reported in other research. 3 It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity simplicity and cost.RESCULTS AND DISCCISSIONRespirable quartz dust used in this study was taken from a stock of crystalline silica, Min-U-Sil; obtained from Pennsylvania Sand Glass Corporation, fractionated in air with a particle classifier. The small size fraction retained for use was 80% less than S micrometer particle diameter, with an area equivalent median diameter of 1.24 micrometers as estimated by automated image analysis. The silica was at least 98.S mass percent silica as determined by X-ray energy spectrometric analysis; and the crystalline form was alpha-quartz as determined by X-ray diffraction. It's specific surface area was 3.97 square meters per gram as determined by nitrogen adsorption isotherm methods. I"

Jan 1, 1990

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Computer input data for an operating mine is developed on the basis of a detailed ventilation survey which includes air quantity, air quality, pressure loss and fan performance measurements. Quantity measurements must be reviewed extensively and assumptions made about leakage quantities and airflow paths. Pressure measurements must be reviewed and developed into a pressure gradient for the mine system. Air quality measurements are used to determine methane sources and amounts. Finally, the fan test data is used to develop the correct fan characteristic curve. Quantities and pressure losses for each branch in the system are used to calculate the branch resistances which are then utilized in the ventilation simulator to model the mine system. QUANTITY BALANCE The quantity of air coming into a mine based on field measurements will rarely equal the quantity exiting the mine, even if allowances are made for methane or compressed air input to the system. The same statement can be made for airflow through any isolated part of the mine ventilation system such as individual working section or main aircourses leading to an area isolated from the rest of the mine. The reason for the apparent discrepancies is the accuracy of the indicated quantities which in turn is based on the accuracy of the individual velocity and area measurements. Even with measurements following the guidelines described in the previous section on quantity measurement, this error can only be minimized but not eliminated. As a result the ventilation system must be carefully balanced so that, for any loop, the quantity in plus any methane or compressed air injection will equal the quantity out. The continuity of flow described by the balanced system must approximate the

Jan 1, 1977

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By H. H. Schrenk

[A calorimetric method3/ for the determination of benzene in amounts as low as 0.001 m has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel from the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations.]

Jan 1, 1935

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"1 Introduction The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rubber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber."

Dec 1, 1919

By Richard L. Sayrs

The Idol zinc prospect, formerly known as the Comstock, was examined by Harold B. Ewoldt, a Bureau of Mines' engineer, accompanied by Deane F. Kent of the United States Geological Survey on July 22, 1943. Previous to that time, the Geological Survey had contoured and studied the area. As a part of the war minerals program, further investigation of the area was recommended. The Dalton property, a mile and a half northeast of the Idol property, was examined during the progress of the work at the Idol, and it was decided to include this property also in the project. From February 7, 1944, to May 16, 1944, six holes totaling 2,739 feet were diamond-drilled on the Idol property and eight holes totaling 1,850 feet were diamond-drilled, and three pits channel sampled on the Dalton property. The drilling showed sphalerite to be sparsely distributed through a 100 foot thickness of the Kingsport member of the Knox dolomite.

Jan 1, 1949

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 110 subsidence monuments. Measurements were taken twelve times during the eight months it took to mine the panel. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By H. C. Miller

[California's sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

By A. W. Effinger

The Bureau of Mines used regression analysis and applied statistical methods in an effort to rationalize the results of an experiment examining the effects of certain variables on carbon deposition in a reservoir for thermal recovery of petroleum. Although none of the 15 trials of the original experiment resulted in the response of weight-percent of carbon regarded by the experimenter as adequate, values calculated using canonical analysis in two trials yielded responses 33 and 54 percent higher than the minimum acceptable figure. The actual responses differed by less than 3 and 6 percent, respectively, from the predicted responses. Methods are described for defining a path of increasing response based on the minimum point and the response surfaces and for defining a set of values for the parameters in question, which result in increased response, A detailed explanation of the mathematical process used in this analysis is presented in the appendix for ease in computer programing the technique.

Jan 1, 1970

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By Roy H. Grau, John C. LaScola

"This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.INTRODUCTIONMethane gas is a threat to safety in underground coal mines. Research by Government and industry has led to great gains in reducing methane gas ignitions and explosions. The development of advanced methane control techniques is necessary for the safe operation of more gassy mines and the implementation of rapid mining techniques.As part of this research, the Bureau of Mines has surveyed total methane emission data from underground bituminous coal mines in the United States and tabulated emissions from mines producing over 0.1 MMcfd of methane. This report is an update of similar studies previously described in Information Circulars 8733, 8659, and 8558 (2-4).3The data from 1980 were compiled from Mine Safety and Health Administration (MSHA) records of air quality-quantity inspections made quarterly at each mine. The inspections involve measuring airflow and collecting air samples in the main returns. From these data, an average methane emission is calculated and used to represent the daily mine emission for each quarter. The methane emissions given in this report are the averages of the four 1980 quarters and do not include mine emissions from other sources such as degasification projects. Since a previous Bureau study showed that emissions from mines emitting less than 0.1 MMcfd represented only 2 pct of all emissions, 0.1 MMcfd was chosen as a lower limit for data collection (4)."

Jan 1, 1982

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By Basil Dimitriades

The association of automotive fuel composition with exhaust reactivity was studied in an experimental program that involved testing with different automotive engines and with gasolines of varied composition. Results showed clearly the exhaust reactivity to increase with increasing levels of polyalkylbenzenes in the fuel. No other systematic patterns of high significance were detected in the association of exhaust reactivity with several broadly defined groups of fuel components. For the purposes of this study, had it been possible, fuel composition should have been defined and expressed in terms of component groups such that the potential for exhaust reactivity would be the same within each group and different from group to group. Classification of fuel components in terms of the paraffins-olefins-aromatics groups does not meet the latter requirements. For appropriate classification of fuel components more information is needed on the combustion .of hydrocarbons in the multicylinder internal combustion engine. Statistical analysis of the mass emissions data showed significant car and fuel effects on hydrocarbon, carbon monoxide, nitric oxide, total aldehydes, and formaldehyde emission levels and on total photochemical reactivity. Car-fuel interactions were not significant at the 90-pct level. Correlations were found between mass emission parameters and fuel composition.

Jan 1, 1973

By G. S. Scott, G. W. Jones, F. E. Scott

An important activity of the Bureau of Mines is the promotion of safety in mining and industry . In connection with these activities , the Bureau determines the explosion hazards of combustible gases , liquids , and solids , and investigates means by which explosions may be eliminated or reduced in violence . The limits of inflammability and ignition temperatures of combustible gases , vapors , and solids are of practical importance because such materials can be manufactured , transported , and used with greater safety , provided the range of concentrations and temperatures that cause explosions are known. Acetic anhydride , ( CH3CO) 20 , with which this report is concerned , is a liquid at ordinary temperatures . It is used in the preparation of a number of organic chemicals and in the manufacture of photographic film and of artificial silk . It is perhaps the most important acetylating agent for industrial uses - a property that is especially important at this time because of its direct application in the manufacture of munitions . The sample tested was supplied by the Carbide & Carbon Chemicals Corporation . Its specific gravity was given as 1.083 at 20/20 . The vapor pressures , supplied by the manufacturer , are plotted in figure 1 .

Dec 1, 1943

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978