Search Documents

By W. H. Ode, W. A. Selvig

Investigations have shown interesting relationships between primary-tar and light-oil yields and chemical analyses of coals. These studies have been based largely upon results published by the Bureau of Mines in connection with its survey of the gas-, coke-, and byproduct-making properties of American coals. This paper gives the results of a similar correlation in which the range in rank and type has been extended to include nearly all classes of coal, the object being to determine relationships that are significant in predicting tar and light-oil yields from chemical analyses of coals. The yields of primary tar and light oil are important in two fields of coal utilization, namely, combustion and carbonization. It is generally recognized that the principal cause of smoke produced upon burning coal is incomplete combustion of tar and light-oil vapor released during burning. The greater the tar and light-oil yields of a coal, the greater is its potential smoke-producing property. During the present war, development of new sources of fuel oil has been emphasized, especially where the supply of petroleum products is limited. One possible source of a substitute fuel is the tar and light oil that can be obtained by low-temperature carbonization of coal. In both England and Germany large quantities of low-temperature tar and oil are being processed as a source of liquid fuels. It is obvious that primary-tar and light-oil yields are of paramount importance in the selection of coals for such use.

Mar 1, 1944

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d&apos;Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius&apos; has damped the vibrations so successfully that a short note concerning it is thought to be desirable. The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several modifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects. These modifications were suggested by careful study of the original idea embraced in the Julius construction. They were designed to give further constraint to motion in any direction other than that parallel to a line from the point of support through the center of gravity of the suspension, This was accomplished by making the suspended frame more rigid and by improving the means of adjusting each of the supporting wires to the same degree, thereby transmitting any impulse symmetrically through the three wires. The result was a suspension that is more effective, particularly for severe vibration, than the form described by Julius; also, it is believed to have advantages in stability, simplicity, and ease of adjustment over the few suspensions for this type of service that the author has found described in the literature.

Jan 1, 1931

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d&apos;Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965

By Floyd G. Anderson

Bureau of Mines studies show than an electronic counter can be used for determining just concentrations from midget impinger samples collected in bituminous coal mines. A sample correlation coefficient of 0.91 for data obtained using the electronic counter and the Bureau of Mines microprojector procedures indicates a significant linear relationship between the methods. The electronic counter provides better counting precision and reduces analytical time.

Jan 1, 1968

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

By R. Hogg

"Agglomeration processes and agglomerate characteristics are largely controlled by the forces of interaction between particles. The nature and typical magnitude of these interaction forces are evaluated relative to the external forces commonly present in agglomeration systems. The specific roles of the interaction forces in the various stages of agglomerate formation and growth and their effects on the integrity and mechanical strength of agglomerates are briefly reviewed. Because the interaction forces affect different aspects of agglomerate development in different ways, conflicting requirements can arise. Examples of such conflicts are given and used to demonstrate the importance of evaluating the effects of interaction forces etc., in the context of the overall agglomeration process and its ultimate objectives.INTRODUCTIONThe term agglomeration is generally used to refer to processes whereby discrete particles are caused, or allowed, to associate into clumps in which the individual particles retain their identity but are held together by relatively weak, usually physical forces. Various other designations are given to these processes, depending on the specific circumstances under which agglomeration occurs. The terms balling and pelletizing are often used to describe agglomeration in dry or semi-dry powders; coagulation and flocculation are used to refer to agglomeration of particles dispersed in fluids. Common to all of these cases is the fact that the formation, growth and integrity of the agglomerates depend primarily on the forces acting on and between particles. The same forces are, of course, responsible for manyaspects of the behavior of colloidal systems and their study and evaluation constitute the,basis for colloid and interface science.FORCES ACTING ON FINE PARTICLES AND AGGLOMERATES It is convenient to classify the forces acting on and between particles into two general types: external forces and interaction forces. It should he recognized, however, that a sharp distinction is not always possible.External Forces Gravity and inertial forces act on all particles and their magnitude is proportional to particle mass, i.e. they vary with the cube of particle size. Such forces are oftensignificant for large agglomerates but may be negligible for individual, fine particles.Hydrodynamic (""drag"") forces are important, for particles suspended in fluids. For very small particles, the drag force is directly proportional to size (Stokes' Law) while for very large particles or agglomerates it varies with approximately the square of size (Newton's Law). A useful procedure for estimating drag forces over a broad range of particle sizes and physical conditions has been given by Concha (1)."

Jan 1, 1989

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Blair Burwell

This paper describing the method of mining a deposit of vanadium ore near Rifle, Colo., is one of a series of similar papers on metal-mining methods and costs being issued by the United States Bureau of Mines. This vanadium deposit probably is the largest yet found in North America. It is situated 12 miles northeast of Rifle, Colo. (see fig. 1), on the southern flank of tae White River plateau, and is at an altitude of 6,500 feet. Between 150 and 200 tons of ore are mined daily and trucked to the mill at Rifle. The product of the mill is fined vanadium oxide, which is shipped to the company&apos;s plaits at Columbiana, Ohio, and Niagara Falls, N. Y., for the electric manufacture of ferrovanadium. HISTORY The deposit was discovered about 1909 by men prospecting for carnotite. Its outcrop on the bola cliff of Rifle Canon had been known to stockmen for many years.

Jan 1, 1932

By S. J. Page, W. E. Wallace, P. Bolsaitis, D. Eppelsheimer, M. J. Keane, J. Poston, J. Harrison

"Respirable-sized dust particles from a clay mine and mill were examined for aluminium and silicon content by scanning electron microscopy-energy dispersive X-ray analysis at incident electron energies of 5--20 keV. Most of the high silica content particles, those which had a silicon to silicon plus aluminium signal fraction, measured at 20 ke V, of0.9 or greater, showed a decrease in the silicon fraction of signal with decreasing incident electron energy, down to values of between 0.6 and 0,8 at 5 keV: this decrease was a function of particle size and composition. Simple models for silicon fractiol) of signal vs incident electron voltage suggest this behavour is due to a heterogeneous particle structure in which an aluminosilicate coating occludes the surface of a silica particle core. The coating survives incubation in a major component of pulmonary surfactant.INTRODUCTIONMINING and some other dusty workplace atmospheres are monitored for respirable dust and quartz dust for purposes of occupational health protection, respirable quartz dust being a known cause of pulmonary disease. Respirable quartz exposure data are acquired also for epidemiological research on the correlation of pulmonary disease prevalence with respirable dust composition and concentration. For these purposes quartz content often is measured on collected dust samples by X-ray diffraction or in spectroscopy. Scanning electron microscopy-energy dispersive X-ray analysis spectrometry (SEM-EDX) is also used. The first two methods measure the bulk composition of a multi-particle dust sample; SEM-EDX measures the elemental composition of single ·particles. These methods as typically applied, including SEM-EDX with a 20-30 kilo-electron volt (keV) electron beam accelerating potential, do not distinguish homogeneous distribution of impurities in a particle from possible heterogeneous surface distribution. These measurements of quartz content are not always accurate predictors of the prevalence of dust-induced disease (ROBOCK and BAUER, 1990), which implies that the biologically available quartz surface may not be equivalent to conventionally measured quartz content of respirable dust in some exposure settings. Using a minor modification of conventional scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) protocols on samples of settled and airborne dust from a clay mine and mill we have detected heterogeneity with depth for aluminium impurity in high silica content particles, indicating that some of the quartz or 'free silica' respirable particles of the dust are aluminosilicate occluded. Coatings were not removed by incubation of the dust in a surrogate pulmonary hypophase surfactant fluid."

Jan 1, 1990

By E. D. Gardner

About 300 tons of gold ore per week was being produced in February 1934 by Thomas D, Herron and Con Laster from the old lake Superior and Arizona workings; the ground was leased from the Magma Copper Co. The workings adjoined but were not a part of the Magma mine. The lessees had been employees of the Magma Copper Co, at the time the Magma closed down for the summer of 1932. Work on the lease began in July 1932 on an exposure of $2-per-ton ore disclosed in a drift; after a few hand-drilled rounds were blasted the gold content increased to about $30 per ton. Extensive sampling by pannings elsewhere of exposed portions of the vein indicated that other ore shoots existed. The last work previously done in the mine was during the World War, when lessees mined a number of small shoots of copper ore. In some of the stapes the copper miners had left a quartzose streak on the hanging wall that carried $15 per ton of gold. This material did not look as if it cried values and evidently never had been sampled. The first shipment of gold ore was made on September 28, 1932. Up to April 1, 1933, 3,778 tons had been shipped and from September 1, 1933, to January 31, 1934, 3,125 tons.

Jan 1, 1934

By V. A. Marple, K. L. Rubow

"In our laboratory several impactors have been developed in the past which have penetration characteristics that approximate that of the ACGIH or the British MRC respirable curves. In these impactors the large nonrespirable particles are collected on an impaction plate of a multiple round nozzle stage where the nozzles are of different diameters. The principle for designing a respirable cut impactor is quite simple in that the respirable curve is divided into two or more segments and the nozzles are designed with the correct diameters and number of nozzles to have collection characteristics with 50% cutpoints at the center of each segment. The particles not collected on the impaction plates are then collected upon a filter. These particles represent the respirable fraction of the aerosol. Therefore the respirable curve is approximated in a stepwise fashion with the approximation becoming better as the respirable curve is divided up into increasing numbers of segments. It has generally been felt that three segments is satisfactory for most cases.A new version of the respirable impactor has recently been developed in our laboratory. This impactor approximates the ACGIH respirable curve in three steps at a flow rate of 30 liters per minute. However, unlike previous models where all of the particles larger than the three cut points designated by the three steps are collected upon one impaction plate, a separate impaction plate is now used for each of the three cut sizes. To approximate the respirable curve in three steps, the cut sizes must be 2.2, 3.5 and 5.8 microns diameter. Therefore, on each of these stages the particles collected will be the mass of particles that are larger than these three cut sizes. By determining the mass of particles collected on each of these three stages plus that on the after filter using Gravimetric techniques, some information can be obtained on the size distribution of the aerosol being sampled. Furthermore, the impaction plates of the three stages are rotated and the nozzles are placed in such a position such that a uniform deposit is obtained on each of the impaction plates. Therefore, the deposits collected are suitable for X-ray fluorescence analysis or other types of analysis where a uniform deposit is required."

Jan 1, 1988

By P. T. Brooks

Electrochemical machining sludge, a troublesome fluid waste product, was dewatered on a bench-scale basis by three alternative methods tested by the Federal Bureau of Mines. These methods would enable recycling 89 percent or more of the liquid content of the sludge and allow the dewatered solids to be dumped as landfill or processed further to recover contained nickel. Dewatering by vacuum precoat filtration was estimated to be the least expensive. Based on treating 20,000 gallons per day of sludge, precoat filtration costs were estimated as totaling 1.96 cents per gallon of sludge. Two options of an alternative method, comprised of acidification, reprecipitation, thickening, and filtration, were estimated to cost either 3.41 or 3.60 cents per gallon of sludge.

Jan 1, 1976

By P. M. Gruzensky

In view of some of the outstanding properties of chromium, considerable effort has been made in recent years to prepare the high-purity metal in ductile form. The object of this investigation was to obtain such metal by electrolysis of chromic acid solutions and to determine the conditions that yield optimum results. The apparatus is described, as well as the parameters that received consideration. Ion-exchange resins were employed to remove cation impurities from the electrolyte. Tensile specimens prepared from the electrodeposits by arc melting, press forging, swaging, and drawing, were ductile at room temperature. INTRODUCTION Metallic chromium displays an exceptionally high resistance to corrosion, oxidation, and wear at elevated temperatures. Although these properties are utilized to some extent when chromium is alloyed with other metals, such as in stainless steels, high-chromium alloys and pure chromium are not employed as engineering materials because of a serious lack of ductility and impact resistance at room temperature. Because high-chromium alloys appear promising as refractory metals for applications such as in gas turbines, much interest has been shown recently in the preparation of uniformly ductile chromium and in determining which factors contribute to its brittleness.

Jan 1, 1957

By W. E. Wallace, V. Robinson, M. F. Keane, V. Vallyathan

"An in vitro study of the biologic responses of surface-modified and native silica and kaolin was made to provide comparative information on the supression of cytotoxicity by pulmonary surfactant. The release of alveolar macrophage cytoplasmic enzyme, lactate dehydrogenase (IDH), and lysosomal enzymes B-N-acetylglocosaminidase (B-NAG) and B-ghucuronidase (B-GLUC) and sheep blood-cell hemolysis were moni¬tored as indicators of cell membrane damage and cytutoxicity. Surface modification of silica and kaolin with dipalmitoyl lecithin (UPI) resulted in complete abrogation of cytotoxicity of both minerals. These findings indicate that surface modification of minerals with different adsorption properties by pulmonary surfactant generally lessens their prompt adverse effects.INTRODUCTIONAcute and chronic silicosis are well-characterized clinical and pathologic entities resulting from the inhalation of crystalline silica (Morgan and Seaton, 1984). Kaolin, a layered aluminosilicate clay frequently mined and used in manufacturing, contains tetrahedral silica alternately layered with alumina octahedra. Kaolin is relatively .inert biologically, and distinctly greater pulmonary burdens are seen in patients with kaolinosis than are seen in patients with silicosis. Crystalline siliea (quartz) induces a significantly greater degree of fibrosis in exposed animals in vivo than does kaolin (Hamilton and Hardy, 1974; Parkes, 1982; Hunter, 1976; Sheers, 1964; Warraki and t-lerant, 1963; Lynch and Mciver, 1954; Lapenas et al., 1984).This difference in pulmonary disease associated with the two types of dust is not reflected by in vitro cytotoxicity as Jetermined by pulmonary macrophage bioassays or erythrocyte hemolysis. Cytotoxicity studies using crystalline silica and kaolin of similar size fractions show comparable bioassay response on a mass basis. These cellular bioassays, therefore, do not correlate with the relative in vivo pathogenicity of silicates."

Jun 1, 1988