Search Documents

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937

By Fei Chen, Lesley J. Gaydos, Laurence M. Demers, Douglas C. Kuhn

The fibrogenic effects of silica in experimental animals and humans has been extensively studied (I 7, 20). However, the pathogenesis and molecular mechanisms underlying lung injury and fibrosis resulting from silica exposure remain to be elucidated. It is well-documented that silica can stimulate monocyte-macrophage lineage cells to produce cytokines and growth factors, including interleukin-I (IL- I) (20), tumor necrosis factor-ex (TNF-cx) (I 7), insulin-like growth factor-I (IGF-1) (4), and transforming growth factor-P (TGF-P) (24). Consequently, it has been suggested that the fibrogenic effect of silica may be mediated by cytokines in the fater stages of silicosis. During the early phase of interaction between silica and the pulmonary alveolar macrophage, several direct and indirect lines of evidence suggest that reactive oxygen intermediates (ROI) may play a pivotal role in silica- induced tissue damage (2I, 22). One of the most important components of and contributors to ROI is nitric oxide (NO) produced from L-arginine and molecular oxygen under the catalytic influence of NO synthase (NOS) (I 9). At present, at least three NOS genes have been cloned: a constitutive neuron NOS, a constitutive endothelial cell NOS and an inducible NOS (iNOS) (16). A number of factors have been shown to differentially induce iNOS gene expression in different cell lines including bacterial cell products and foreign antigens. During inflammation, NO is a double-edged sword in terms of the host immune defense mechanisms and the physiologic response to an inflammatory insult. The macrophage is one of the major cellular sources of NO. During the early phase of acute inflammation, NO produced from the macrophage appears to facilitate the clearance of pathogens and promotes a local relaxation effect on the microcirculation of vascular smooth muscle. When the production of NO is left unattenuated, especially under oxidative stress, direct cytotoxic effects of NO can emerge through the formation of peroxynitrite as a result of a reaction between NO and superoxide (2).

Jan 1, 1998

By H. B. Freaman, C. L. Colburn, C. M. Bouton

"The mine telephone has been perfected to such an extent that it is giving satisfaction in most mines were the wiring is well insulated. Very often the telephone cannot be depended upon on account of falls of rock, grounding due to worn insulation or extreme dampness. In the event of a disaster it frequently happens that the mine telephone system is put out of commission by the agency that causes the disaster, at the time when it is most urgently needed. On this account the mining industry is interested in any kind of telephone system that can be counted upon in an emergency. Many requests have been received by the Bureau of Mines to devise means of utilizing wireless methods for this purpose.The results of some preliminary experiments conducted by the writers at the Bureau of Mines experimental mine at Bruceton, Pennsylvania, in the ordinary sending and receiving of radio waves through earth strata are described below. The experiments were made in cooperation with the Westinghouse Electric end Manufacturing Co., which assigned to this work three of its radio engineers, C. A, Boddie, E. C. Douglas, and F. D. Fessler,The preliminary experiments consisted first in receiving signals from without the mine by means of a receiver located inside the mina, and second, both sending and receiving messages underground through the strata. It was found that with a receiving instrument set at a point 100 feet underground, signals from KDKA station, of the Westinghouse Electric and Manufacturing Co. East Pittsburgh, Pa., could be heard distinctly. Station KDKA is at a distance of about 18 miles from the experimental mine. About 50 feet from the receiving station used in this test was a 6-inch bore-hole from the surface, lined with iron pipe and containing electric light wires which extended therefrom through-out the mine. The presence of these wires evidently assisted greatly in the reception, for when the receiving set was carried to another point in the mine removed from wires and tracks the signals were barely audible through 50 feet of cover. The fact that signals were detected, however, even though faintly, is sufficient evidence of transmission through the ground to encourage further experimenting.In sending waves underground the Westinghouse 20-watt B.T. model T.F. transmitter was used in such a manner as to send out continuous waves of 200 to 300 meters length."

Oct 1, 1922

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By Earl R. McMillan

"Coal washing commands the thoughtful attention of a steadily incre in number of people. Clean coal is not merely a luxury but is rapidly becoming a necessity in some industrial operations.Coal seams in the Northeast are rarely free from ""bone"" and shale or clay partings which vary from a fraction of an inch to several feet in thickness. Nearly all of the coal measures are folded and faulted, the coal seams dip at various angles, and in some cases are badly broken. In mining these seams fragments of the roof and floor, as well as partings of impur-ities within the seams, unavoidably become mixed with the coal, so that the raw coal as it comes to the surface often contains as much as 50 per cent, by weight of waste.At the Bureau of Mines experiment station at Seattle, the washing of this coal in order to improve it for commercial use has been studied. Since the process of coal-washing depends upon differences in specific gravity between the clean coal and, its associated impurities, the first problem undertaken was that of determining the specific gravity of the clean coal and of each parting of impurity contained in a large number of representative seams.It was found that the freshly-mined coal is practically saturated with water, this being observed in determining the effect of moisture content upon the specific gravity of the coal particles, selected from samples of coal varying from low-grade subbituminous up to semianthracite, all of which are found in the State of Washington. The specific gravity values determined for the cleanest particles varied from 1.28 to 1.35; in general, the higher the rank of the coal the hither the specific gravity."

Nov 1, 1920

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By M. R. Geer

The washability examination of a coal establishes the quality of the product that could be prepared by mechanical cleaning, shows how much impurity would have to be eliminated to attain a particular quality of product, indicates what type of cleaning process would be suitable, and tells whether the coal could be cleaned efficiently, The coal-preparation laboratories of the Bureau of Mines make washability examinations of coal for a variety of purposes. Sometimes these examinations are made as an integral part of research conducted on coal-washing problems. Occasionally they are made on coals mined on Government-owned land or on coals destined for use in Government installations. Often they are made on coals from new fields or new beds in existing fields to help establish the characteristics of the Nation's coal reserves. Whatever the original reason for doing the work, the results often are useful later in evaluating deposits or in the design of cleaning plants. Publication of the results of such studies provides for the widest possible usefulness. This report brings together the results of washability examinations made on 1 coal each from Oregon and Idaho, 2 from Wyoming, 5 from Utah, and 11 from Washington. Material of this nature is inherently difficult to summarize. Some of the coals are so clean} despite full-scam mechanical mining, that they could not be improved materially by washing; others present some of the most difficult preparation problems found in the country.

Jan 1, 1961

By R. T. Johansen

The wettability of petroleum reservoir materials by water and crude oil has been recognized as an important factor in determining waterflood behavior. The problem of simulating and studying reservoir conditions and characteristics, to produce laboratory results congruous with field experience, has been examined by many methods. (1, 2, 3, 4).4/ The most generally accepted approach to this problem is determining wettability of the porous medium by imbibition methods; or, after solvent extraction, predetermining the wettability of the samples by coating the surface of the medium to render it preferentially oil-or water-wet (3, 5). The emphasis of wettability studies has been placed on the characteristics of the reservoir materials with little consideration being given to the fluids themselves. Therefore, the wetting tendencies of crude oils have been investigated by a recently developed method (6). Imbibition and the more general phenomena of capillary pressure are the most direct ways to measure wettability. The simplest type of capillary pressure observations involves the use of an interfacial-tension capillarimeter, which does not produce as separate values either interfacial tension or contact angle. Actually, these quantities do not have independent significance in reservoir engineering, and the property of wettability they are intended to evaluate is given, immediately by capillarimetric measurements.

Jan 1, 1961

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By John Zetterstrom

Increased activity in the beneficiation of taconite, particularly the magnetic variety, has shown the need for more information on the rate of oxidation of magnetite to hematite. This oxidation occurs in the pelletizing step of the beneficiation process. Magnetic taconite is an intimate association of magnetite and a siliceous gangue. It must be ground to approximately 70 to 30 percent minus 325 mesh to liberate the magnetite from the gangue. With sufficient liberation, magnetic concentration will yield a product high enough in iron and low enough in silica for blast-furnace use. The magnetic concentrate must be agglomerated before it can be used in a blast furnace. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron-oxide materials, sintering and pelletizing being the two most common methods. Sintering is clone on a Dwight-Lloyd or Greenawalt sintering machine. Pelletizing consists of balling fine, moist oxide in a rotating drum, followed by baking at .a temperature below that of incipient fusion to develop a permanent bond within each pellet. The magnetic concentrate from taconite is too fine for good sintering practice but fine enough for good pelletizing practice.

Jan 1, 1950

By Kenneth Lipman

Auxiliary equipment was assembled around a purchased oscillograph to permit observation of the current and voltage characteristics of low-energy, capacitance-discharge sparks having durations of at least 10 mµ-sec. Circuit details of the assembled apparatus, performance characteristics of the complete system, and some preliminary data from representative self-initiated sparks are given in this report. INTRODUCTION One of the subjects of continuing research by the Federal Bureau of Mines Division of Explosives Technology is the ignition of explosive-gas mixtures by means of low-energy capacitance sparks. Quite early in these investigations it was recognized that understanding the gas-ignition phenomena would be facilitated by detailed information about the performance of the ignition source (spark) under the actual conditions of interest; however, the sparks of practical interest are nonrepetitive transient phenomena whose duration could reasonably be estimated to be in the time range of 1 mµsec. to 1 µsec. As such, the only feasible method of obtaining detailed information was and is oscillographic representation of the pertinent current and voltage transients. It was not until 1947 that a suitable, commercial, dual-channel oscillograph could be obtained as the basic instrument for these studies; the instrument specified in 1947 was delivered in 1950. This paper describes the auxiliary

Jan 1, 1959

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

By John C. Machisak

THIS CHAPTER reports employment data and injury experience in the metal, nonmetal, quarrying, sand and gravel, and slag (iron blast furnace) industries of the United States in 1959. Each industry is treated separately, and no attempt has been made to combine data to show an overall total for this group of mineral industries. The slag canvass is included for the first time (data on employment and injuries were not collected before 1958), and, like other canvasses included in this chapter, data are voluntary. Employment and injury experience for all mineral industries can be found in volume III. The employment and injury information in this chapter came from reports submitted to the Bureau of Mines before May 31, 1960; therefore, figures are preliminary and subject to revision. Voluntary reports submitted by operators have contributed substantially to safety promotion since 1911, when the Federal Bureau of Mines started collecting employment and injury facts.

Jan 1, 1960

By D. J. Bauer, V. E. Shaw

Bastnasite concentrate was processed to recover total rare - earth content and obtain high - purity ceric nitrate . Reaction of the concentrate with 45 percent caustic soda for 1 hour at 180 ° C in stainless steel vessels resulted in 99 - percent conversion to rare - earth hydroxides . A drying step followed by solution in nitric acid produced a tetravalent cerium fraction amenable to extraction with TBP . Single- stage separatory funnel experiments resulted in 90 -percent recovery of ceric nitrate at a purity of 99.9 percent . Fractional extraction in pressure - bubbler columns resulted in 98.5 - percent recovery of 99.5 -percent - pure ceric nitrate .

Jan 1, 1964

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By Michael G. Zabetakis, Aldo L. Furno, George H. Martindill

Hydrazine vapor is flammable in the absence of air at elevated temperatures and atmospheric pressure . The minimum concentrations of benzene , toluene , m- xylene , cumene , and n- heptane needed to inhibit flame propagation through vapor mixtures of hydrazine and hydrocarbon were determined at 125 ° C and atmospheric pressure . These concentrations can be correlated with either the heat of formation or the heat capacity of the hydrocarbon .

Jan 1, 1964

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By R. F. Waters

The Bureau of Mines developed laboratory-scale processes to recover sodium phosphates and metal values from waste sludges generated by the phosphate treatment of automobile and appliance components. After treatment of the sludge with NaOH, followed by coke or hydrogen reduction and sintering, zinc and lead were recovered as fume; the sinter was separated by leaching into a metallic product, chiefly iron and nickel, and high-purity disodium or trisodium phosphate.

Jan 1, 1971