Search Documents

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

To improve efficiency in producing clarified water from mineral and metallurgical processing streams containing suspended particles. Approach Particles suspended in mineral and metallurgical processing streams are filtered out by granular magnesium oxide (MgO) used as the medium in deep bed filters. How It Works MgO is substituted for the silica sand or garnet sand currently used in conventional deep bed filters. These filters presently consist of a 24- to-48-inch-deep layer of either silica sand or mixed media, consisting of a stratified combination of anthracite coal, silica sand, and garnet sand. As waste water containing fine solids is percolated through the granular bed, the suspended particles become attached to the filter grains. When MgO replaces sand as a filter medium, the overall filter capacity is generally increased 50 to 80 percent, and no equipment modifications are necessary for filter operation. MgO is unique because it has a positive surface charge in water while most suspended materials are negative. The attraction of these negatively charged suspended particles to MgO enhances filtering performance. As is necessary for all good media, MgO is insoluble and nontoxic.

Jan 1, 1983

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

By R. F. Abernethy

The work discussed in this report was done by the Bureau of Mines to develop a method for determining trace amounts of fluorine in coal. Samples of coal mixed with calcium oxide as a fixative agent for fluorine were ashed at 600° C and the residue was fused with sodium carbonate. The melt was dissolved in phosphoric and sulfuric acids and distilled to separate the fluorine) which was determined in the distillate by a SPADNS-zirconium spectrophotometric method. Fluorine determinations of 83 commercial coals ranged from 0,001 to 0.019 percent.

Jan 1, 1967

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By W. R. Reed

Dust dispersion modeling is a subject that has had a large amount of research activity. Much of the research has focused on large-scale global or regional dispersion models. Other models have been created for industry-specific purposes. Furthermore, some of the past research has focused on dust dispersion modeling in the mining industry. This report presents the various dust dispersion models that have been developed specifically for the mining industry. The report first gives a brief background of the regulatory environment that helped to promote development of such models. It then presents an overview of the mathematical concepts used in this dispersion modeling. Finally, each of the various models developed for the mining industry are described, along with their associated mathematical algorithms and any field validation conducted on the different models.

Jan 9, 2005

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By Mark A. Ackerson, Kenneth E. Hjelmstad

An ideal fire warning alarm system for underground mines would be low cost, convenient, fast, reliable, and able to warn all underground workers. Present warning systems, such as phones, messengers, and stench, fail one or more of these criteria. The U.S. Bureau of Mines may have devised the ideal system. The one way communication system employs a large loop antenna and transmitter to create a 630 hertz (Hz) electromagnetic field to send information through-the-earth to cap lamp battery mounted micro- receivers worn by underground miners. Field tests of prototype equipment in 1986 resulted in through-the- rock signal transmission of over 762 m (2500 ft). Subsequent hardware upgrades for more recent tests resulted in transmissions of over one mile. Recently developed receiver circuitry employs phase- locked-loop detection circuitry responsive only to a specific series of pulses of given time duration, that eliminates false alarms from electromagnetic noise emitted by mine equipment, power lines, or lightning. A multichannel system can relay standard messages to miners

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

By E. W. Dean, W. A. Jacobs

"The petroleum division of the Bureau of Mines in its laboratory investigations, has had occasions to develop a number of types of electrical heating equipment. It was found that electric heaters could be used to particular advantage in the standard distillation test for gasoline. (Dean, E.W., Motor Gasoline, Properties, Laboratory Methods of Testing and Practical Specifications, Bureau of Mines Technical raper 214, 1919, 33 pages.) In order to assist in rendering this type of heater available for general use, a description of the apparatus developed by the Bureau was published. (Dean, E.W., A convenient electric heater for use in the analytical distillation of gasoline,. Jour. Ind, and Eng. Chem., Vol.10, 1918, page 823.) Shortly after the article was printed a chemical supply house undertook the manufacture of an electric heater suitable for gasoline distillation. A preliminary model was examined and tested by the Bureau and modifications were suggested that were incorporated in the type of heater that was finally marketed.Description of the Bureau of Mines-heater: The electric heater developed by the Bureau has an inverted conical resistance Plament surrounded by a layer of heat-insulating material and mounted in a metal case having a top of hard asbestos (Transite) board. The resistance element is a helix of nickel-chromium alloy wire held by a molded core of alundum. The Bureau heaters are generally of about 330 watts capacity and are used with stock types of regulating rheostats capable of reducing the effective wattage to about 43 the full-load maximum."

Jun 1, 1920

By George E. Fasching

The Bureau of Mines has developed a pulse counting system with improved energy resolution and having dual channels to process pulses at different rates and a pulse pileup detector for channel selection. Pulse input is delayed until the detector determines if any pulse is so closely followed by a second pulse as to constitute pulse pileup. If no pulse pileup is detected, the slower channel is selected; this clips the pulse to a wide pulse width to retain good energy resolution. If pulse pileup is predicted, the fast channel, with correspondingly shorter pulse width, is selected to improve resolution with respect to time. Output of the two channels is transmitted to a pulse height analyzer for interpretation. The pulse processing system can process count rates above 300,000 counts per second with little loss in energy resolution.

Jan 1, 1974

Provide a method of detecting and locating miners trapped underground following a mine disaster. Approach Develop a surface deployed system which senses the vibrations caused by a trapped miner pounding on the roof of the mine and effectively determines the miner's location. How It Works If trapped underground, a miner would strike the roof of the mine with any implement at his disposal. This pounding causes vibrations in the ground which are transmitted to the surface where they are sensed by receiving transducers called geophones. Multiple geophones are positioned together for noise cancellation purposes in a form called a subarray. Seven

Jan 1, 1981

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By T. Bajpayee, L. Prosser, A. Iannacchione, G. Esterhuizen

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques to help identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk-analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and could provide the kind of information needed by on-site personnel responsible for worker safety to mitigate roof fall injuries.

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By W. G. Bradley

THIS PAPER describing the quarrying, mining, and crushing of gypsum at the Blue Diamond mine, 11 miles from Arden, Nev., on the Union Pacific Railway, is one of a series on gypsum mining being prepared for and published by the Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total production costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932