Search Documents

By Edward F. Divers

The Bureau of Mines recently tested a sideboard device that is designed to act as an extension of conventional brattice, thus improving face ventilation of developing room-and-pillar-type coal mining. In these laboratory tests, an 8-foot-long rigid sideboard was mounted vertically along the left fender of a full-scale-model ripper-type continuous mining machine, rising to the mine roof to provide an air seal. It extended from the auger support frame pivot point outby along the fender. A novel water spray manifold was used to form an air seal between the sideboard and brattice. Tests showed improvement in face ventilation with the prototype device, and also demonstrated that water sprays can form an effective air seal over a fairly wide pressure range. Based on this preliminary study, subsequent improvements may make the sideboard concept much more effective, thus affording a simple, inexpensive technique to improve the effectiveness of face ventilation.

Jan 1, 1979

By John A. Breslin

Three scale models of coal mine entries and mining machines were constructed by the Bureau of Mines to study the effects of ventilation parameters on dust concentrations where mining personnel would be working. A one-fifth-scale model of a coal mine entry with a drum-type continuous-mining machine and a one-sixth-scale model of an entry with a twin-borer-type machine were used as well as a one-fifth-scale model of a longwall face with a double-drum shearer. Methane was used as a tracer gas to simulate respirable dust in the models. The distance of the end of the brattice or tubing from the face was found to be more important than the airflow rate for the drum-type machine. Dust reductions greater than 90 pct were shown to be possible with a secondary ventilation system used with the twin borer and a dust collector mounted on the longwall shearer. Cutting-head speed had a significant effect on concentrations at typical positions of miners with the drum-type machine and longwall shearer but not for the twin borer.

Jan 1, 1976

By Elaine T. Cullen

Educating the public about the role of mining and minerals can be a challenge. While it sometimes seems that little is being done to counteract negative publicity, there are many exciting things happening across the country that are helping meet this challenge. This paper will discuss existing minerals education activities and will provide tips for developing successful programs for a variety of groups, from students to industry to minerals educators themselves. The paper will also include an overview of the 9th annual National Minerals Education Conference held in July 2000 in Spokane, WA.

By James J. Olson

The Bureau of Mines recorded both particle accelerations and velocities from one-stick and production blasts at Eagle-Picher Industries' Shullsburg mine, Shullsburg, Wis., to test the effectiveness of square root scaling in grouping underground blast vibrations and to determine the effects of rock type and mine geometry on blast vibrations. Although the charge weights of subsequent delay periods sometimes exceeded the charge weight of the zero-delay period, both acceleration and velocity records showed that the zero-delay portion of the Shullsburg production blasts produced the highest vibration amplitudes. Because of the restricted range of charge weights in the Shullsburg experiments, no statistical determination of an appropriate scaling factor could be made. However, the square root scaled peak particle velocity data from the Shullsburg production blasts grouped well within the approximate band-width of vibration data obtained by the Bureau from quarry blasts in many different rock types. This indicates that scaling by some factor, perhaps the square root or cube root of the charge weight, may be an effective way to group and study vibration data from underground blasts. Further research is needed to determine which scaling factor is best for underground blasting.

Jan 1, 1970

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth trans- mission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By N. E. Hanna

The effect of small percentages of sodium chloride on the incendivity of permissible explosives was studied by the Bruceton up-and-down technique in gallery tests. Both the reduction in incendivity achieved by addition of sodium chloride and application of the test method to explosives evaluation are discussed. It is demonstrated that the up-and-down technique in gallery testing is suitable for distinguishing differences in incendivity between different explosive compositions and between lots of the same composition. The study also shows that addition of relatively small quantities of sodium chloride tends to reduce the incendivity of explosives to firedamp, but addition of sodium chloride cannot insure reduced incendivity. Any improvement attributable to the salt can be counteracted by undefined variations in the explosive. The need for experimental investigations of a number of factors that may affect the safety of permissible explosives is emphasized. ACKNOWLEDGMENTS Grateful acknowledgment is made of the assistance of Roy L. Grant in analyzing for normality of distribution of the data obtained by the up-and-down methods and to Harold E. Tubbs for numerous calculations.

Jan 1, 1959

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By Edward L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

By J. J. Demeter

A tube-wall reactor with a Raney nickel catalyst deposited on the outer wall of the tube by flame spraying is effective in the practically complete conversion of 3H2+1CO synthesis gas to a high-Btu gas (methane) at an hourly space velocity of 7,000 volumes of gas (NTP) per hour per volume of annular volume. Partially reacted synthesis gas containing an appreciable amount of methane can also be treated in this reactor to increase the heating value to over 900 Btu per cubic foot. Excellent heat removal through the metal wall to a coolant and temperature control were obtained. The heat transfer co-efficient from the catalyst to the coolant was about 275 Btu per hour per square foot per ° F. Synthesis tests were conducted with tubes 1.2 inches in ad by 6 inches long, and 1.3 inches in od by 36 inches long. When operating at a synthesis gas rate of 100 to 120 scfh per square foot of catalyst-coated tube, catalyst life was long enough to realize a catalyst cost for the raw Raney nickel alloy of about 0.3 cent per 1,000 cubic feet of pipeline gas (900 to 950 Btu per scf). Gas recycling at ratios of 1:1 to 3:1 was effective in increasing conversion and in extending the life of the catalyst to about 16 weeks. In cost and in operating characteristics the tube-wall reactor compares favorably with the fluidized-bed and hot-gas-recycle reactor systems for the synthesis of high-Btu gas from H2+CO.

Jan 1, 1967

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005