Search Documents

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

To evaluate the potential for dust reduction, during blasthole drilling, of water or foam applied directly into the drill hole. Approach The Bureau of Mines tested a through-the-drill-steel water and foam injection technique in two noncoal mines to evaluate the method's potential for greater dust reduction. The tests were performed by drilling a series of blastholes for an entire face (a 90 minute time-period). For the first 45 minutes of drilling, foam or water was applied through the drill steel. Blowing ventilation was supplied to the entry about 50 feet from the face. The dust concentration measurements were made by a Real-Time Aerosol Monitor (RAM-I), and the data were read out on a strip chart recorder. The evaluation test results showed that the water or foam injection technique, when used on localized dust sources, can be an extremely effective dust control method. Small amounts of water used in this method have also allowed it flexibility to be used in water-soluble ores such as salt, gypsum, anhydrite, and trona. How The System Works Water or foam is mixed with compressed air (approximately 100-120 psi) with suitable metering systems and forced through the drill steel into the blast hole at the point of dust generation. Because the water or foam is applied at the source, minimal quantities of liquid are needed (0.2 to 0.6 gpm). These low flowrates are sufficient to just moisten the dust emerging from the blast hole, thus eliminating a major source of airborne dust. The wet drilling procedure also eliminates a second source of dust. With dry drilling, the dust from the blast hole falls to the floor. Since this can be a 15-ft drop or more, the impact can send the dust billowing up from the floor, adding to the airborne dust. With wet drilling, the moistened dust merely dribbles down the face.

Jan 1, 1982

By S. R. B. Cooke

Certain saturated and unsaturated fatty acids and a variety of resin acids were used as collectors for specular hematite, magnetite, and goethite. Vacuum flotation tests were used with each collector and mineral to delimit the fields of flotation and nonflotation as functions of concentrations of collector and of hydrogen ion. The experimental results of these tests lead to the following conclusions. The respective fatty and resin acids exhibit characteristic fields of flotation and nonflotation for the three iron oxides. The fields are somewhat similar, and specular hematite apparently is the most floatable mineral. The insolubility of some of the organic acids may seriously restrict flotation at low pH, although the saturated fatty acids, caprylic and capric, collect minus-100, plus-150-mesh specular hematite only in acid pulp. The presence of a lower "critical pH" is explained on the basis of the dissociation and hydrolysis of dilute soap solutions.

Jan 1, 1959

By James H. Aase

Selected glacial lake clay deposits in Minnesota were sampled, tested, and evaluated to determine their suitability for use as a bonding agent in iron ore pellet manufacturing. Preliminary tests conducted on clay samples obtained from five ancient glacial lake basins identified the clays in the Lake Agassiz glacial lake basin near Cook, Minn., as having the greatest bonding potential. An auger drilling program was conducted to obtain substantial quantities of representative material for detailed testing. The drilling indicated the presence of large clay reserves in excess of 500 million tons within the 12-square-mile area investigated. Bench scale tests indicated that the bonding properties of Cook area clays, when activated with relatively small quantities of sodium carbonate monohydrate (Na2C03?H2O), imparted excellent strength characteristics to iron ore pellets. Larger scale continuous pelletizing tests were made to confirm the bench scale results. These tests indicated that use of 1 percent activated clay alone as binder gave the iron ore pellets an overall strength slightly lower than with 0.75 percent bentonite, considered the industry standard. Use of 0.5 percent activated clay plus 0.5 percent bentonite produced better pellet strength qualities than use of 0.75 percent bentonite alone, without increasing the silica plus alumina content. The data from both bench scale and larger scale continuous tests suggest that the Cook, Minn., clays can be utilized after activation either alone or in combination with bentonite at an economic advantage over present pelletizing practice with bentonite.

Jan 1, 1968

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By C. J. Thompson

In the course of the work currently conducted by the Bureau of Mines in cooperation with the American Petroleum Institute Research Project 48 on identifying sulfur compounds in petroleum, a micromethod was developed (12)5 for catalytically removing the sulfur atom from sulfur compounds. The product is the residual portion of the molecule; the structure otherwise was unaltered except for hydrogenation of any unsaturated bonds that were present in the original compound. Positive identification of sulfur compounds isolated from crude oils is a difficult problem. Direct comparison of properties of the unknown with those of reference compounds is often impossible because of the limited number of reference sulfur compounds available. However, a relatively large number of pure hydrocarbons is available, and the conversion of the sulfur compound to a hydrocarbon enhances the possibility of identification. The technique also can be used to prepare microquantities of scarce hydrocarbons by hydrogenating compounds that are readily available.

Jan 1, 1962

By J. D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings in the form of stress and deflection coefficients from which bending, axial, shear, and boundary stresses, moments, thrusts, and shear forces, and structural deflections can be determined at any point on the lining. Results were obtained by structural analyses of nine concrete-lined tunnel configurations subjected to 22 biaxial load conditions. The tunnel configurations include three basic shapes, circular, rectangular, and horse-shoe, with dimensions based on designs evolved by the mining industry. These analyses were made by the direct stiffness matrix method, a computer-oriented procedure. Numerical results agree closely with those obtained experimentally.

Jan 1, 1969

By Robert H. Lambeth

The Madison RARE II study area has four prospects with identified resources. These are listed in table 1 and are described in the following text. A high potential for Sillimanite exists at the Placer Creek occurrence (fig. 1, no. 7) and potential for phosphate rack in all areas underlain by the Phosphoria Formation. Some prospects exhibit minor potential for copper, lead, zinc, silver, and gold in the southern portion and very minor potential in the northern portion. Deposits in the northern end also have low potential for rare earth, asbestiform anthophyllite, or kyanite group minerals (including sillimanite).

Jan 1, 1982

By George H. Schnakenberg, Aleksandar D. Bugarski

This report reviews the performance and applicability of technology for the control of emissions from diesel-powered equipment used in underground coal and metal/nonmetal mines. The methods discussed include Mine Safety and Health Administration-approved low-emission engines, engine derating, fuels, fuel additives, diesel oxidation catalysts, and diesel particulate filters. The potential of each of these technologies is examined individually and in combination. The performance estimates are derived from the published literature and presented in narrative and Tabular form. The purpose of this report is to help the mining industry select the most appropriate method to reduce underground exposures of miners to diesel exhaust in the context of the recently developed diesel regulations. It is important to note that the control technologies discussed in this report have received limited evaluation in underground mines. Additional research is ongoing, and some engineering design changes may need to be implemented before all of these diesel emission control technologies can be safely and successfully used in underground mines.

Jan 1, 2002

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By R. J. Shanley

This report presents a computer code that has been developed by the Bureau of Mines for isolating naturally occurring clusters of data plotted on the unit hemisphere and testing these clusters against a probability distribution which admits elliptical symmetry about its mean. A listing of the computer code is provided along with an example output illustrating the delineation and analysis of clusters in fracture orientations measured in a porphyry copper deposit.

Jan 1, 1975

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By H. B. Cooke

In connection with its researches on the crude petroleums of the United States, the Bureau of Mines has made a particular study of apparatus for the distillation of hydrocarbon mixtures. While this study is still incomplete it has already resulted in the development of considerable laboratory and semi-plant equipment, motet of which has been described in various publications of the Bureau. The laboratory apparatus (Hempel distillation) and method gives satisfactory comparative results in the laboratory examination of crudes and have been found applicable to crudes of all types, but the agreement of laboratory and plant distillations is not as close as might be desired. This is due, in part, to limitations in size and construction of the laboratory apparatus. Some refiners claim that the Bureau of Mines' laboratory method (Hempel distillation3) for distilling crude petroleum, does not show the full gasoline content of the oil, while others have stated that it indicates more gasoline than can be obtained from the crude commercially. This difference of opinion among refiners results largely from the great variation in stills used and methods of operating them. The Bureau's experience has shown that crude oils from different fields vary widely in character; in fact, that it is not yet possible to classify crude's adequately on the basis of their Down chemical and physical characteristics. As a result of the differences that exist among crudes, and of the difficulty of designing refinery equipment, no standard practice has yet been adopted for the commercial distillation of petroleum, and ma" types of stills are used in the refineries of this country. Although many factors enter into the design of equipment and the development of commercial practice in refining of crude oil, there

Jan 1, 1924