Search Documents

By W. Dan Walker

In an effort to keep mine hoist accidents to a minimum and to impart to managers and workers the essential elements that enter into safe installation and maintenance of hoisting equipment, the Bureau of Mines presents this Information Circular as a guide. Hoisting of men and materials is an essential operation in many mines and has become so commonplace that some persons are likely to ignore day-to-day inspections or become lax in the operating phases. With proper maintenance and operation, hoists can be exceptionally safe. However, lack of strict attention can invite tragedy or costly shutdowns.

Jan 1, 1961

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By L. C. IlsLey

From time to time the Bureau of Mines has issued publications dealing with the various classes of explosion-proof mining machinery that have been tested and approved as permissible for use in mines having atmospheres that may become inflammable by reason of the inadvertent presence of gas or dust. These publications are confined almost entirely to description of the features contributing directly or indirectly to the prevention of explosion or shock hazards, and are intended to give inspectors, safety engineers, and others already familiar with the general safety requirements more detailed information on the safety features of the design of a particular machine. As a background for papers describing permissible machines and to avoid the necessity of duplicating descriptions of methods of conducting investigations and tests of such machinery, Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, was pub¬lished in 1929. Three bulletins giving detailed descriptions of the three most numerous types of machines have been issued, viz., Bulletin 313, Permissible Storage-Battery Locomotive and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 392, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By Harley A. Coy

This paper, describing the mining methods and practice at No. 2 mine of the American Zino Co. of Tennessee at Mascot, Tenn., is one of a series of papers issued by the Bureau of Mines presenting the mining methods and costs in various districts throughout the United States. Its purpose is to summarize methods recently put into practice whereby increased efficiency has been effected. These improvements have to do principally with mill-hole mining, slushing, contract labor, and bonuses. In general, this paper supplements earlier articles and brings them up to date. ACKNOWLEDGMENTS The author acknowledges the assistance of M. H. Newman, geologist of the American Zinc, Lead & Smelting Co.; of William Black, assistant superintendent of mines; of P. M. Arthur, director of personnel; and of the engineering staff. The paper has been approved by H. I. Young, vice president and manager of operations.

Jan 1, 1930

By U. E. Brown

This papery describing the mining methods employed by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the United States. The Bunker Hill and Sullivan mines are situated in the western part of the Coeur d'Alene district at Kellogg, Shoshone County, Idaho. The mines were discovered during the summer of 1885 and except for two short periods of labor trouble, between 1890 and 1900, have been in continuous operation. About 575 men are employed at the mine. The production is about 1,400 tons of lead-silver ore per day. This is treated in the company's concentrator and smelter at Kellogg.

Jan 1, 1931

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By I. F. Avery

The productive capacity of natural gasoline and cycling plants in the United States on January 1, 1956, was 46.4 million gallons per day, according to the Bureau of Mines r biennial survey. This represented an increase of 7.5 million gallons per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 4.8 million gallons per day. The total number of plants increased from 535 on January 1, 1954, to 600 on January 1, 1956. The number of operating plants increased from 521 to 571. The major increases in capacity took place in Texas, Louisiana, New Mexico, and Oklahoma, with the absorption-type plants continuing to account for most of the new construction. All types of plants showed construction gains with the exception of charcoal which showed no change.

Jan 1, 1957

By L. C. IlsLey

Minin,g Qr col-cu.ttint till:I chines are 1?;\i9ng the _m9t wideiy .used de1sses ()f mining equipment.· These 1T:.i:1Chines ,.--re practicaily t-tl\·operc1_ted eiyher_by compressed .iir or by electric. ·motors. According to &.ta• compiled _ from the 122. issue COAL CATALOG\JE. OJMEINED WITH; OOAL "FIELD 'pf!:fC'TOTl1, bf 7,088. mnes from which reports were obttiined there -are 3895 mines that u.se coal-cutting eql;lipmen:ts,, 'f'hi report lists 20,031: r.ct:lchines, 17,&75 being operated by·elct:i.c.m<;>_tors··:r;id :the remtiinder by compressed i.r motors,· ,-. · ', .. . · .. ··, .. _ ,· .,, .. .. . . . . . : ; "'l t:: On tl.Ccou-nt .. of the wide· use of coc:11-cutting -.:i"cliine_- any Stat!;ls have issued regulationa as "to their operation dnd be to safety precautions that.should be observed J especially in gaseous mines.

Oct 1, 1922

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health, National Personal Protective Technology Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the seventh phase of testing from May 1999 to August 2000. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. The results indicate that most of the apparatus, if they pass their approved inspection criteria, perform satisfactorily. The deployed CSE SR-100s, however, exhibited significantly higher inhaled carbon dioxide (CO2) levels than new units, as they did in the previous two phases. Several Draeger OXY K-Pluses that rattled when shaken were found to have potassium superoxide (KO2) particles throughout the breathing circuit, including the mouthpiece. Draeger investigated the problem and developed a shake test to detect damaged units. The durations of new Ocenco M-20s were statistically significantly longer than those of deployed units, although only by 2 min.

Jan 3, 2002

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i&apos;1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By A. Bartkowiak

The lower flammability limit of methane at 0 p.s.i.g. and ambient temperatures is 5.6 volume percent in chlorine, 5.2 in oxygen, and 5.0 in air. The corresponding upper limit values are 70, 60.5, and 15 volume percent, respectively, so that the range of flammable mixtures is greater in chlorine than in oxygen or air. The lower flammability limit of ethane at 0 p.s.i.g. and ambient temperatures is 6.1 volume percent in chlorine, 3.0 in oxygen, and 2.9 in air. The corresponding upper limits are 58, 66, and 12.5 volume percent, respectively. In this instance the range of flammable mixtures is greater in oxygen than in chlorine or air. Generally, the limits of flammability for both methane-chlorine mixtures and ethane-chlorine mixtures widen with increases in temperature and pressure.

Jan 1, 1960

By J. B. Littlefield

This study is one of at number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling; information as to various factors connected with, drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it in particularly desirable to ascertain whet features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found.

Jan 1, 1938

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By Ray J. Holmquist

"INTRODUCTION The Copper King or Red River copper mine was examined on December 13, 1942, by the Bureau of Mines at the request of Richard Kelly of Santa Fe, N. Mex. The examination was made to determine whether the expenditure of funds for rehabilitation work necessary to make the workings accessible for examination would be warranted.As a favorable report was made, the workings of the Copper King mine were opened and sampled under the direction of the author. The portal of the Copper King adit was opened first. Considerable rehabilitation was necessary in the first 50 feet of the workings, but the remainder of the drifts and crosscuts were sufficiently open to permit surveying and sampling.An attempt was made to open the Waterbury atilt, which was reported to be about 30 feet east of the Copper King portal, and to crosscut the ore body nearly to its southern border. However, slide rock and mine dumps had completely obscured the portal of this adit, and no opening into it could be found or made.Work on the project was started on September 27 and vas completed on November 6, 1943."

Apr 1, 1947

By R. V. Ramani, A. S. C. Owili-eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. Part of the research reported here was originally done on a grant from the Department of Environmental Resources, Commonwealth of Pennsylvania and reported in Special Research Report No. SR-95 (February 25, 1973) of the Coal Research Board, The Pennsylvania State University.

Jan 1, 1974

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972