Search Documents

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By D. Debasis, Christopher Mark, Gregory M. Molinda

The stability of any underground opening is, in large part, a function of the strength of the rock mass which surrounds it. The Coal Mine Roof Rating (CMRR) has been developed to quantify the defects in the rock mass and compile a strength value which can be used for engineering design. The CMRR has been applied to a number of ground stability problems, including chain pillar design, roof bolt selection, hazard assessment, intersection design, and numerical modeling. The CMRR procedure and some of these applications are described in this paper. The CMRR will soon be available in a Visual Basic computer program, allowing easy integration into exploration programs and standard roof fall assessments.

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Charles L. Kimbell

Some comment on data availability must be an integral part of a study such as this. For many years, the centrally planned economy nations of the world regarded as state secrets much of their mineral commodity production information, as well as a considerable body of the foreign trade information on these commodities, and virtually all reporting on their consumption. Within the past 5 years, this pattern has undergone some evolution, and although these countries still fall short of market economy countries in their willingness to publish, there has been measurable improvement. Fit, China, and then subsequently the former CMEA member countries of Eastern Europe have released in print an increasing amount of information in organized, coherent formats, although in a number of cases it is not clear that the information provided is in perfect definitional accord with market economy country practices. Thus, these recently available statistics must be carefully studied to ensure that they are provided in terms of conventional market economy definitions. At the same time that heretofore unpublished information is becoming available for the centrally planned (or formally centrally planned) economy countries, there has been a slow but steady disquieting erosion of availability of production, trade, and consumption data for market economy countries. There are evident reasons for some of these losses in information. The foremost of these relates to corporate mergers. As the number of producing or consuming firms of a given commodity in a given political jurisdiction declines, it is increasingly difficult for government agencies to protect proprietary company data. In past years, this protection was afforded by aggregating data for the several companies operating in the area, but as the number of operators diminishes this is no longer always possible. Hopefully, given this situation, companies will at least authorize release of data after a period of time, when its publication will not provide competitors with unfair access, but will make possible longer term studies.

Jan 1, 1992

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

Roof screening for ground control originated with metal miners in the western United States. At first chain-link fence was used, but because it was so difficult to handle, the miners started installing a more rigid welded wire screen used in the concrete industry. Eventually coal mines in the west began to use screen, and now more and more coal operations, especially longwall mines, are installing roof screen on a regular basis. Screen use has recently increased in the Illinois basin and is now making its way to underground coal mines in the eastern U.S.

By John R. Shattuck

As a part of the general chromite investigation in California designed to aid In the production of chromite during the recent war emergency, the Bureau of Mines explored the Coggins property in Siskiyou County, Work by the Bureau in cooperation with the Federal Geological Survey began in October 1942 and was concluded in March 1943. This report presents a brief history of the mine, outlines the physical features of the district, describes the deposits) and explains the work completed by the Bureau of Mines, Table 1 shows the analysis of diamond drill-hole samples. The logs of drill holes are in the appendix.

Jan 1, 1949

By W. W. Adams

"A gratifying decrease is noticeable in the number of men killed in the coal minas of the United States during the past six months as compared to the quantity of coal produced.During July last year, when 221 men lost their lives, the production of coal was over 50 million tons. In January, 1920, the production had increased to 56 million tons, or 11 per cent, while the fatalities, instead of increasing proportionately, actually decreased to 166, or nearly 15 per cent. Nor is this decrease a mere accident or coincidence peculiar to the month of January, as may be seen from the following table.From the figures shown above it may be observed that the average monthly production for January and the five months immediately preceding, was 49,500,000, or only 2 per cent below that for July, while the average number of men killed was 183, or a decrease of over 17 per cent."

Mar 1, 1920

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

One of the major unknowns in the use of iron and copper is the quantity of various low level impurities, particularly hydrogen, that may be introduced during the deoxidizing process prior to casting. Introduction of hydrogen results in the embrittlement of components made from these metals. In addition, hydrogen bubbles in castings of copper result in the formation of blisters and swelling of the casting. During the last year, a significant effort has been made at the University of Missouri-Rolla to understand the permeation of hydrogen in galvanized automotive steel components and the hydrogen absorption during the electrodeposition of copper. The galvanized steel components consisted of automotive upholstery clips, seat belt holders and brake clips. Although the process of galvanization protects the steel from corrosion the process invariably causes the steel to pick up enough hydrogen to make it susceptible to brittle fracture.

Jan 1, 1992

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By L. E. Schultze

[The Bureau of Mines conducted bench-scale studies to develop techniques for stripping tetravalent cerium from tri-n-butyl phosphate solutions. Experiments were conducted in a constant-temperature bath using beakers and mechanical stirring. Ninety-five pct of the cerium was stripped from a 50-pct tri-n-butyl phosphate 50-pct kerosene solution containing 0.18 M cerium in 15 minutes at 50° C using 0.11 M aqueous formaldehyde.]

Jan 1, 1974

By Robert C. Hickman

"INTRODUCTION The Big Four fault and the Sandy Creek fault, with several cross faults, traverse the Stalion-Curnel fluorspar prospect in a northeasterly direction. The Big Four mine, about three-quarters of a mile northeast of the prospect, is the only active mine in the immediate area.A resistivity survey was made of a portion of the prospect by the Division of Geophysical Exploration, Bureau of Mines, in May and June 1946. As a result of this survey, five holes were drilled by the Bureau of Mines during the period from October 8 to December 16, 1946. Two Longyear No. 12 Junior Straitline diamond drills were used for the work.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the supervision of Mitchell H. Kline, chief, Raleigh Branch, Mining Division."

Mar 1, 1948

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By William H. Pomroy

Fires in underground metal and nonmetal mines pose a threat to the safety of underground miners and to the productive capacity of this Nation's mines. Contaminated air (smoke, carbon monoxide, and other products of combustion) is the primary life safety hazard created by a mine fire. The most reliable defense against the hazard posed by the rapid spread of contaminated air underground is early warning fire detection and rapid evacuation. This Bureau of Mines report describes the design and operation of four prototype early warning fire detection systems, for underground noncoal mines, presently undergoing prolonged in-mine testing by the Bureau. The systems are described within the context of the underground mine environment.

Jan 1, 1985