Search Documents

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988

By R. S. Dean

A general survey of the metallurgical work of the U. S. Bureau of Mines has been given in an article in the Missouri School of Mines Alumnus, and a somewhat more detailed review of the bureau work on lead and zinc will be found in the Mining Congress Journal. C. C. Furnas has contributed one general mathematical article. Dean, R. S. U. S. Bureau of Mines. 4, 1930, pp. 7-8. Program of Metallurgical Investigations of the Missouri School of Mines Alumnus, vol. 4, No. Investigations of the U. S. Bureau of Mines on the Milling and Smelting of Lead and Zinc. Min. Cong. Jour., vol. 16, 1930, p. 799, 808. Furnas, C. c. Evaluation of the Modified Bessel Function of Am. Mathematical Monthly, vol. 37, the First Kind and Zeroth Order. No. 6, 1930, pp. 282-287.

Apr 1, 1931

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By R. R. Hornor

BIBLIOGRAPHY OF ARTICLES RELATING TO THE PRESERVATION

Apr 1, 1922

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By I. AITKENS

The precious stones rubies and sapphires are transparent varieties of the mineral corundum . Essentially they are aluminum oxide , but the aluminum is often replaced. by small amounts of chromium , titanium , or iron . The chromium is said to give a red color , titanium a blue , and iron a yellow . True rubies range from rose to a somewhat purplish red and are sometimes termed " oriental rubies " to distinguish them from spinel rubies , stones of inferior hardness , density , and value . " Oriental rubies " are very rare , and the so-called " pigeon's blood" variety is the most valuable . Sapphires normally range in color from palest blue to deepest indigo , but actually all precious varieties of corundum of any other color than red are called sapphires . The most esteemed tint is like that of the blue cornflower . Colorless corundum of gem quality is called white sapphire ; the yellow variety is described either as yellow or as golden sapphire ; and the pale pink is classed as pink sapphire . The word " oriental " is also used as a prefix in naming varieties of corumdum of less popular colors . For instance , oriental emerald is used for green corundum, oriental topaz for yellow , and oriental amethyst for violet to purple varieties . The chief physical characteristics of rubies and sapphires are hardness , adamantine luster , and moderately high specific gravity ( 3.9 to 4.1) . Next to the diamond, corundum is the hardest of all minerals ; in fact , the sapphire is number 9 on Moh's scale , ranking between the topaz and the diamond. Rubies crystallize in 6-sided prisms terminated by flat faces and other varieties of corundum with twelve inclined faces , six above and six below , meeting in a girdle . Corundum is doubly refractive , with a direction of single refraction running parallel to the edge of the prism . The refractive indexes are very constant, the ordinary index ranging from 1.766 to 1.774 and the extraordinary index from 1.757 to 1.765. The double refraction always remains the same.

Aug 1, 1931

By Jon I. Voltz

The U.S. Bureau of Mines has conducted fundamental coal fragmentation studies to evaluate the effects of impact energy and direction of bedding planes on dust generation, size distribution, and impact-output energy relationships. Product size distributions were obtained for the fragmented samples by screening to minus 150 mesh. The minus lS0-mesh fines were analyzed with a light scattering photometer with a measurement range of 176 to 1.9 /.tm. Increased input energy produced a significant increase in the weight of plus 3/8-in material for impact perpendicular to the bedding planes. No significant trend was observed for parallel impact. Impact direction had little influence on dust size distribution, and input versus output energy relationships. As expected, total airborne dust measured at time of impact and percent particulates below 11 /.tm in size generally increased with increased input energy for both directions of impact. Energy used for sample fragmentation increased with increased energy input.

Jan 1, 1989

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By Ellsworth Spencer

Noise induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A).(1) The focus of this research was to determine the noise exposures of heavy construction equipment operators while documenting the workers’ tasks, (i.e. hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were studied for this research located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25,836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1,397%.

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974