Search Documents

By Katherine Harding

Basic concepts of matrix algebra and manipulations of matrices are presented in such a way that little competence in mathematics is required. Examples are always included to illustrate concepts and techniques. The paper is divided into six sections. The first four sections are devoted to some of the more basic concepts of matrix algebra, whereas the last two sections are concerned with specific applications.

Jan 1, 1967

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By Ruth F. Brinkley

Principle activities of the Bureau of Mines Explosives Research Laboratory from July 1, 1960 to June 30, 1961 are reviewed briefly in Part 1. Part 1 also includes data obtained in connect ion with several minor investigations which are not sufficient to warrant separate publications. Part 2 gives brief abstracts of publications that appeared during fiscal year 1961; in general, the research reported in these publications antedates this period.

Jan 1, 1963

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By Patrick D. Plumb

The Bureau of Mines (BOM) has begun a project to increase the understanding of the relationships between ecosystem health and its functions, and minerals development. The BOM, Juneau Branch, Alaska Field Operations Center, is providing support for ecosystem based land-management decision-making and the development of ecosystem based regulations by documenting the effects of mining on ecosystems and demonstrating the tools used to assess and analyze those effects. This is done by reviewing the data available on ecosystems and the environment at a mining site, the Greens Creek Mine near Juneau, Alaska, and applying available Geographic Information System modeling tools to assess the impacts of the mine on components of the pristine ecosystem. Habitat Capability Models for wildlife indicator species are used in this examination. Wildlife indicator species are used as indicators of ecosystem health by the U.S. Forest Service and the Alaska Department of Fish and Game, who developed these models for southeast Alaska. Analysis techniques from the U.S. Fish and Wildlife Service's Habitat Evaluation Procedures (HEP) are also used in this report. By applying available models and analytical techniques to the Greens Creek area, the benefits gained through mitigation of potential impacts become apparent. These or similar techniques are useful for cost/benefit analysis of mitigation alternatives. Also apparent from this analysis is that the degree to which potential impacts are observable will depend upon the ecosystem scale considered. This demonstrates the importance of defining the ecosystem and scale before performing impact and cost/benefit analysis. The watershed scale is found to be useful for assessing impacts to ecosystem components at the Greens Creek Mine. Much progress remains to be made in the modeling and prediction of impacts to ecosystems from mining activity.

Jan 1, 1994

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By A. N. Fried

One of the important problems confronting oil producers in appraising the possibilities of secondary recovery in many California fields is the effect of viscosity on oil recovery by water flooding. In January 1954 there were 554 fields and/or pools, in the State, that produced 1 million barrels daily, and 138 of these pools produced approximately 267 thousand barrels daily of heavy crude oil having gravities below 200 API. Many of these fields are nearing the end of their primary economic life and still have high residual-oil saturations, a favorable factor in water flooding. The crux of the problem is whether or not enough oil can be recovered from these fields by water flooding to make the operation economically successful. Some experiments on the relationship between viscosity and oil recovery have been made by other investigators, but in most instances the viscosity of the oils used in the experiments was lower than the viscosity of the oils found in many of the heavy-oil fields in California. A study was undertaken, therefore, to determine the relationship between oil viscosity and recovery over a wider range of viscosities and to compare the experimental results with those predicted by theoretical calculations.

Jan 1, 1955

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By L. C. IlsLey

A list of permissible mine equipment, tested and approved prior to Jan 1, 1937, was published in Bureau of Mines Information Circular 6942 • .ll The present list inc ludes additional equipment approved during the calendar yea r 1937. The ma terial has been listed und er the same. headings as th ose used. in Information Circular 6942. The number that appears at the beginning of each it em represents the number o f this type of ma.chine appr.oved including the machine in questi on; for instance, the miing ma.chine numbered 70 was the seventiet h co al cutting ma chine design for which approval has been isnued. All of the equipment listed represents new designs except that covered by the first item, that is, 57 under the • heading nLoading Machines and Conveyors. 11 This item covers the approval of the 500-volt design of a machine the 250-v olt design of which was approved on January 17, 1935. The system under wich these devices were tested permits the manu-. facturer., after his equipment has passed certain tests prescribed by the 'Ui"eau of Mines, to mark his equipment with a seal showing that it has been approved by the Bureau. These tests are designed to insure t hat equipments hav,e the minimum requirements for safety in use. The only object of the :Bureau in making such tests and publishing lists of permissible equipment is to help decrease the hazards of mining.

Apr 1, 1938

By W. H. Oppelt

A lignite from west-central North Dakota (Mercer County) was dried by the Bureau of Mines by the Fleissner process at saturated steam pressures to 1,500 pounds per square inch absolute (p.s.i.a.). Normally, the process is operated at pressures of 200 to 370 p.s.i.a. At the highest pressure the temperature of the saturated stearn is 596° F. The purpose of the investigation was to evaluate the influence of very high stearn pressure and temperature on moisture removal, steam consumption, and physical and chemical characteristics of the dried lignite. Two drying cycles were used: A normal cycle, corresponding to previously established standard time requirements, and an accelerated cycle, wherein time requirements were determined by boiler capacity and handling speed. Blank tests to determine stearn requirements for heating the empty autoclave were performed for each cycle and each test condition. Moisture removal, final moisture content, net steam consumption, and size stability of the dried lignite were determined.

Jan 1, 1959

By A. B. Hooker

Many attempts have been made to develop methane detectors that will be safer and more accurate than the flame safety lamps used to detect methane in mines. The development has taken two general forms, namely: (1) Methane detectors, in which the evidence of methane depends entirely upon changes in the appearance of the detecting element, such as a flame or filament; (2) indicating methane detectors or those equipped with scales upon which the approximate percentage is definitely indicated. As an aid in the development of suitable detectors, the United States Bureau of Mines has assembled and published in its Schedule 8B a set of minimum requirements which tests and experience have shown desirable for methane detectors. Any manufacturer may submit his detector for inspection and tests leading to approval under this schedule.

Jan 1, 1930

By H. E. Perlee

Autoignition temperatures and limits of flammability of nine halogenated hydrocarbons in atmospheres of air, oxygen, and nitrogen tetroxide were measured in a modified standard autoignition apparatus and limit-of-flammability apparatus previously developed at the Bureau of Nines. Of the nine halogenated hydrocarbons investigates--bromochloromethane, bromotrifluoromethane, bromochlorodifluoromethane, 1,1,2-trichlorotrifluoroethane, 1-bromo-l-chloro-2,2,2-trifluoroethane, dibromodifluoromethane, l,2-dibromo-1,1,2,2-tetrafluoro-ethane, 1,1,1,3,3-pentachlorotrifluoropropane, and l-bromo-2,4-dichloro-1,1,2, 3,3,4-hexafluorobutane--two formed flammable mixtures with nitrogen tetroxide and six with oxygen; none formed flammable mixtures with air. Three of the halogenated hydrocarbons formed no flammable zones with any of the three oxidizing atmospheres. For those halogenated hydrocarbons that supported combustion in oxygen atmospheres, explosion pressures developed during constant-volume burning of mixtures near the middle of the flammable zone were observed to range from about 6 psig for dibromodifluoromethane to 158 psig for 1-bromo-1-chloro-2,2,2-trifluoroethane. In all cases, the calculated burning velocities of these mixtures were less than 8 in/sec.

Jan 1, 1966

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

1, Introduction This report is submitted in fulfillment of the requirements of USBM Contract No. J0255017, "Development of Emergency Escape Systems Guidelines for Underground Metal and Nonmetal Mines" Under this contract the history of past mine fires was studied. Representative metal and nonmetal mines were surveyed and escapeways, refuge chambers, life support, and emergency hoist requirements were studied to determine the problems in complying with the proposed regulatory standards and their enforcement by MESA Mine Inspectors. In addition, a computer program was written to evaluate mine evacuation performance. The completed program is included in the appendix. 1. 1 Historical Review of Metal and Nonmetal Mine Fires Early records of mine fires are poorly documented because there was no statutory provision for reporting fires to the Bureau of Mines. The survey of representative mines during the course of this contract indicated that many small fires still go unreported even though they are now required to report all fires A recent report survey approximately 80 disasters in metal and nonmetal mines, (6 ) Table I is a summary of some of these fires. Historically most metal and nonmetal mine fires have been caused by electrical problems. Spontaneous combustion and the use of welding equipment are the other major causes of mine fires(14) Although not documented, many mine personnel agree that 30 percent to 40 percent of underground metal and nonmetal mine fires have their origin from cigarettes and other smoking related materials. The number of fires related to spontaneous combustion is decreasing and equipment fires are on the increase. The reduction of spontaneous combustion fires can be attributed to the use of sandfill in more mines and the increase in equipment fires to the increased use of LHD equipment.

Jan 1, 1976

By E. G. Davis

A research program to evaluate the use of ceramic die inserts for ferrous diecasting was initiated by the Bureau of Mines at its Tuscaloosa Research Center. Data were compiled from the literature to characterize selected ceramic materials with respect to thermal properties, thermal-shock resistance factors, chemical reactions with molten metals, and processes required to form die components. With this information and a computer model developed for predicting temperature and stress patterns induced in ceramic materials during simulated ferrous diecasting operations, 27 candidate materials were evaluated. After evaluation, only 15 were considered for testing in an apparatus constructed to immerse the ceramic specimens in molten cast iron. Of these, 13 were tested in a modified testing unit in which cast iron was poured onto the specimens. These tests resulted in the selection of three materials for further testing: boron carbonitride (50 pct B4C:5O pct BN), boron nitride-grade M (BN-M, 40 pct BN, 60 pct Si02), and pyrolytic boron nitride (PBN). Tests in a gravity-flow die unit showed that PBN was thermal-shock resistant and could be used in diecasting of ferrous metals.

Jan 1, 1981

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By Aarne Visnapuu

Dissociation and vaporization of gold chlorides and bromides were investigated by a static pressure method and by Knudsen cell mass spectrometer. Two distinct chlorine and three distinct bromine pressure-temperature relation-ships were observed for the respective salts. The chlorine pressures are attributed to the dissociation of Au2Cl6 and Au2C12, and the bromine pressures to the dissociation of Au2Br6, Au2Br4, and AU2Br2, These pressure-temperature relationships were used to calculate dissociation pressure equations, enthalpies, and entropies of dissociation for each salt. Mass analysis of the vapors over AU2Cls between 83° and 152° C confirmed the existence of gaseous AU2C16. Ionization potential of this molecule is 11.0±0.1 ev and enthalpy of vaporization is 28.l±2.0 kcal/mole. Mass analysis of the vapors over the gold bromides detected only Bra in the temperature range 15°-150° C.

Jan 1, 1971

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941