Search Documents

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result-ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coal bed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beckley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By J. H. Field

Capital and operating costs have been estimated for removing sulfur dioxide from flue gases of a powerplant of 12,000-kw. capacity by liquid-purification processes, using limestone, ammonia, or sodium sulfite as the reactant. The annnonia and sodium sulfite processes yield end products that may be marketable. Coals containing about 1.5 and 5.0 percent sulfure have been considered. The sulfur dioxide content of the gases to be treated is 0.083 and 0.30 percent, respectively. Estimates have been made for 90-percent removal of the sulfur dioxide from both gases. A third instance has been considered in which 70 percent of the sulfur dioxide is removed from the flue gas of 0.30-percent concentration. The scrubbed gas would contain 0.09 percent sulfur dioxide, which might be within the permissible limit for discharge to the atmosphere in most areas. Although it is unlikely that flue gases with sulfur dioxide concentrations of less than 0.10 percent would require purification, a cost estimate for such a gas is included because an estimate is available for a British plant employing the limestone process at these conditions. Capital investment and operating costs, with no credit for products, are lowest for the limestone process for gases of both concentrations. Crediting the ammonium sulfate and sulfur produced in the ammonia process at their market prices at the end of 1956 of $32 and $28 per ton, respectively, the operating costs of the ammonia process become the lowest for purification of the gas containing 0.30 percent sulfur dioxide. The operating costs of the sodium sulfite process for purifying gas of high sulfur dioxide content approach those of the limestone process when the byproduct sulfur dioxide is credited at $14 per ton. Even if credit for products is allowed for the ammonia and sodium sulfite processes, the operating costs are higher than those of the limestone process for the gas of low sulfur dioxide content. Because of the large quantity of materials that would be produced by removing sulfur dioxide from a relatively small number of plants, credit for products should be allowed with extreme caution.

Jan 1, 1959

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By Daniel R. Babich, Jeffrey R. Vipperman, Eric R. Bauer

Prolonged exposure to loud noise can cause permanent damage to the auditory nerve and/or its sensory components. Despite regulations and efforts by government and industry to reduce noise-induced hearing loss (NIHL), it is still a problem in the U.S. coal mining industry. The Mine Safety and Health Administration noise standard (30 CFR3 62), which was enacted in September 2000, is aimed at reducing NIHL in the mining industry. To address NIHL in various aspects of coal mining and provide the necessary information to effectively implement control technologies, the National Institute for Occupational Safety and Health conducted a cross-sectional survey of noise sources and worker noise exposures. Noise surveys consisting of full-shift worker noise exposure (dose) determination, time-motion studies (task observations), and equipment and/or area noise profiling were completed in 8 underground coal mines, 10 surface coal mines, and 8 coal preparation plants. The studies revealed that more than 40% of all workers monitored were subject to noise exposures above 90 dBA TWA8. A summary of these studies is presented, their application to administrative and engineering controls is discussed, and exposure reduction methods are reviewed.

Jan 12, 2006

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By David C. Byrne

From an engineering perspective an ideal industrial noise control solution focuses directly on the actual source of the poise. Eliminating the noise-generating mechanism altogether obviates the need for other noise contra l treatments or hearing protection devices. However, in cases where attenuating the source is not feasible engineering controls must be oriented toward blocking the path that the sound waves travel toward employees. Acoustical enclosures are commonly used as sound path treatments to contain the noise from a machine: alternatively a control room/booth or equipment operator's cab may be used to isolate the worker from the noise. Anyone who has successfully used acoustical enclosures knows that the design procurement, and installation process is deceptively simple. Alt too often First-time efforts fait to account for many of the constraints that can render the enclosure essentially useless. Things that cannot be overlooked include: providing convenient worker access (physical and visual): allowing for proper machine operation/product flow; and supplying fresh air or preventing undue heat or contaminate build-up inside the enclosure. All of these factors must be given careful consideration, otherwise the enclosure will not perform adequately.

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

By R. V. Ramani

"In Part 1 of this two-part paper the characteristics of mine disasters and their effects are presented with case studies from coal, metal and non-metal mines leading to an amplification of their causes and opportunities for control. The disasters discussed encompass those which threaten the health and the safety of miners and those which affect the general population. In Part 2 of the paper, which will be published in the November 1995 issue of Natural Resources Forum, the approaches to hazard and disaster control are reviewed with particular attention to laws and regulations to promote health and safety at the workplace, and general welfare in mining communities. Further, a systems approach to disaster control is outlined.The mining industry is one of the three basic industries the other two being agriculture, and wildlife and fisheries. It is the process of mining which makes available the riches of the earth - the energy and mineral resources - to benefit humanity. In fact the progress of the human race through the ages is indelibly attached to prowess in exploiting these riches. The stone, iron and bronze ages are markers not just of a time in history but achievements of monumental proportions in the mining and beneficiation of natural resources. Even in agriculture, the remarkable success stories are associated with the prudent use of mined products to enhance production and productivity. The significance of a thriving mining industry to the wealth and security of a nation is therefore unquestioned.Unfortunately, the public's image of the mining industry is often associated with the mining disasters which receive wide coverage in the local and national media. Mine disasters command tremendous attention because of their infrequent occurrence and the extent of human suffering involved. Whether it is an explosion or a fire, or the opening or closing of a mine, the lives of people are touched by the personal and societal impacts of these events.Courts of inquiry of mining disasters have often concluded that the disaster situation was ever present and could have been detected with diligent search. In addition human error has been identified as one of the most frequent immediate causes for the precipitation of the disaster. For the most part, then, mining disasters are caused by man."

Dec 1, 1996

By W. H. Oppelt

A small, annular-retort gasifier having a nominal capacity of 40 pounds of lignite per hour was designed and constructed at the Lignite Experiment Station, Grand Forks, N. Dak. The purpose of the investigation was to increase the capacity of an annular-retort gasifier by better temperature distribution in the heating chamber (adjacent to the annulus) and by supplemental internal heating with controlled amounts of air. Correct control of air admission should yield crude ammonia-synthesis gas having a (H2+CO)-N2 ratio of 3. Dakota Star stoker-size lignite was used during the exploratory experimental program. The effects of temperature level and distribution in the heating chamber and of addition of air to the reactor were investigated. Hydrogen - carbon monoxide ratios ranged from 1.9 to 2.5, and (H2+C0)-N2 ratios were as low as 2.9. Hourly gas production ranged from 970 to 2,580 cu. ft., or 62.0 to 164 cu. ft. per sq. ft. of heated surface, or 350 to 940 cu. ft. per cu. ft. of reactor volume. Data from the small gasifier could be readily correlated with those previously obtained in the commercial-scale unit under comparable experimental conditions.

Jan 1, 1957

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Sidney Katell

The reaction of coal, oil, or natural gas with air and oxygen and/or steam yields a gas containing varying amounts of impurities. Depending on the raw material and the end use of the product, these impurities include solids, such as dust or slag, and gases, such as hydrogen sulfide, carbon dioxide, and nitrogen. Considerable effort has been expended in developing and operating purification systems, and the literature is replete with equipment data and operating results. The research problems, the design, and the operation of the various systems have been the subjects of patent applications, journal articles, and textbooks.

Jan 1, 1959

By B. W. Dunning

The Bureau of Mines investigated the concentration and distribution of precious metals in the various fractions produced from mechanical processing of obsolete military electronic scrap. Whole avionic units, printed circuit cards, and electrical connectors were processed and analyzed. Materials recovered included baghouse lights, wire bundles, mag-netics, and metal concentrates from eddy-current and high-tension sepa-ration. Higher value fractions were processed by a commercial toll refiner for recovery of gold and silver. Lower value fractions were analyzed by the Bureau. Three fractions, the lights, wire bundles, and metallics from high-tension separation, contained most of the precious metals. Depending on the type of scrap feed, these fractions represented 34 to 60 pct of the original sample weight. Collectively, they represented 68 to 97 pct and 75 to 98 pct of the contained gold and silver, respectively.

Jan 1, 1983

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and. investigations of subbituminous coal and lignite.4/ Appropriations were made in July 19 7, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typical subbituminous coal was selected for an extended series of tests in the standard. Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncoking coal was the first one of its rank that had been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall temperatures ranging from 500°C. to 1,110°C. in 100°C. steps. All products are collected and measured; their physical and chemical properties are then carefully determined to ascertain the gas- and coke-making properties of the coal. During the last 10 years approximately 50 representative American coals have been tested in the Bureau of Mines equipment. The results on the first 30 coals and a complete description of the test procedure are contained in a joint publication of the Bureau of Mines and the American Gas Association.7/ The remaining twenty coals have been reported in Bureau of Mines reports as Technical Papers and Bulletins.

Jan 1, 1939

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985