Search Documents

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By James M. Stuckey

In a search for improved methods of upgrading tar obtained by low-temperature carbonization of coal, monoethanolamine (MEA) was found to be effective in extracting tar acids from coal tar distillates derived from a subbitunwous and a lignite coal. Patch extractions showed that both yield and purity of the extracted acids improved with increasing volume ratios of monoethanolamine to tar acid, varied from 1:4 to 8:1. Yield improved, but purity decreased as the concentration of monoethanolamine was changed from 30 to 70 volume-percent, and as the concentration of tar acid in distillate was increased ad from 14 to 45 percent. In a continuous countercurrent extraction employing a double solvent (monoethanolamine and hexane) approximately 80 percent of the tar acids was extracted from 170° to 350° C. tar distillate when using 1.6:1 volume ratios of amine:tar acids. Tar acids isolated from his extract, although of improved purity, contained appreciable quantities of neutral oils and some tar bases. Aqueous monoethanolamine was not effective for extracting the last 10 to 15 percent of tar acids in 170° to 350° C. distillate oil from lignite coal. The highest yield of isolated tar acids and the best recovery of monoethanolamine were obtained by diluting the extract with water and saturating with C02. Some losses of solvent were encountered when aqueous monoethanolamine solutions were heated through decomposition of the amine with the liberation of ammonia.

Jan 1, 1960

By C. J. Chindgren

Upgrading of commercial red cake and recovery of vanadium oxide from uranium-vanadium mill solutions were investigated by the Bureau of Mines. Alternative procedures potentially useful for manufacture of high-quality vanadium oxide at the mill site were explored and developed. The simplest and best procedure for converting commercial red cake containing about 10 percent combined sodium and potassium oxides (Na20) (K20) into a 98- to 99-percent vanadium pentoxide (V205 product appeared to be a metathesis in an ammoniacal solution of ammonium sulfate. Molybdenum, as well as the alkali metal oxides, was removed from the red cake by this procedure at a modest expenditure of labor and reagents. When preparing vanadium oxide of higher grade, it was necessary to dissolve the red cake and reprecipitate the vanadium as ammonium metavanadate. Calcination at 450° C, decomposed the metavanadate and yielded oxide of about 99.5 percent V205. By recyrstallizing the metavanadate before decomposition, an oxide product approaching 99.9-percent purity was obtained.

Jan 1, 1962

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

By Arden D. Fugate

This work was conducted to determine a feasible process for converting siliceous fluoride offgases to a commercially usable product. The offgases were generated by pyrohydrolytic defluorination of low-grade fluorspar in a gas-fired rotary kiln, and fluorine was collected as a hydrofluoric-fluosilicic acid. A silicon-free fluoride solution for further processing was then produced by neutralizing the acidic scrubber solution with anhydrous ammonia, silicon being separated as orthosilicic acid. Ninety to ninety-nine percent of the fluorine originally present remained in solution as ammonium fluoride. Silicon was also separated from synthetic fluosilicic acids, having F-to-Si weight ratios ranging from 3.50 to 14.3. The solutions below a ratio of 4.06, the F-to-Si ratio of H2SiF6, containing dissolved silicon were desiliconized as completely as those containing less than the stoichiometric quantity of silicon. An electrolytic-grade cryolite was recovered from the ammonium fluoride solution by reacting with either sodium aluminate or alumina trihydrate and sodium hydroxide. A product containing 97 to 100 percent of the fluorine, represented by Na3A1F6, was recovered, and 94 to 99 percent of the theoretical yield was realized.

Jan 1, 1963

By Oliver Bowles

"Score of the Bureau's Investigations.There has been outlined in a previous report* the results obtained regarding the adaptability of pulverized waste slate as a filler in road asphalt mixtures. As pointed out in that report the percentage of waste at slate quarries is very high, and the Bureau of Mines has undertaken the problem of discovering new and enlarged outlets for the waste material.Many products such as paper, rubber, road asphalt, floor coverings, paints, etc., require as one of their important constituents a considerable percentage of finely pulverized inert mineral matter to give ""body"", to obtain the desired consistency, or to supply the necessary wearing or other qualities demanded. Such materials are known as ""fillers"". The possibility that slate flour might be used as a filler with advantage in several products other than road asphalt led the Bureau to undertake further investigation.The Importance of Discovering Advantageous UsesIt has been found that in some products slate may be substituted for materials now in use without any marked effect on the quality of the products. A wider use of slate in such products could result only from a definite price advantage as compared with other fillers. Mile it is probable that waste slate may be placed on the market at prices which will encourage its wider use, it is evident that a waste slate utilization industry can never attain sufficient magnitude to definitely assist the slate producers unless it is demonstrated that some definite advantage in quality may be gained when slate is substituted for fillers now in use. The main purpose kept in view throughout the inquiry has been, therefore, to find advantageous uses for waste slate in order that both producer and consumer may be benefited."

Sep 1, 1921

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The tactual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the twelfth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate halt-township map. The description of each half township is followed by a description of each deposit developed in that halt township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) spin trapping experiments have been carried out to investigate the mechanism of sulfite oxidation em¬ploying 5,5-dimethyl-l-pyrroline-1-oxide (DMPO) as a spin trap. The results show that sulfite autoxidation, catalyzed by Mn(II), involves not only the SO-3 radicals but also the •OH radicals. An addition of H2 02 to the sulfite aqueous medium significantly increases the •OH radical formation. This result provides new clues to the chemical mechanism of the sulfite oxidation and the sulfite toxicity.INTRODUCTIONStudies of the oxidation of the sulfite (SO 2-/3) ions under various conditions are of high current interest because excessive exposure to sulfite is toxic and the origin of this toxicity seems to involve sulfite oxidative pathways [1]. An important fact is that human exposure to sulfite is on the increase [1,2]. Some of the increase in the sulfite exposure is linked to the fact that SO2 is a major air pollutant [2] and in aqueous media SO2 exists in equilibrium with SO2-/3. In addition, beverages and foods are common sources of sulfite intake. For example, sulfite is used extensively in the wine industry as an inhibitor of yeasts and bacteria and is present in finished wines in concentrations up to 6 mM [1]. Sulfite is also often added to dehydrated fruits, vegetables and soups, as well as fruit juices and beer [1,3,4]. Because of these, the mean daily intake of sulfite from diet (in the United States) has been estimated to be between 0.0014 and 0.14 mM/kg body weight [1]. At such high levels, sulfite exposure can have toxic effects, such as the induction of an acute asthmatic state [5,6]. Sulfite also appears to have adverse genetic effects [7] and can act as a mutagen or comutagen [8] and a cocarcinogen [5,7-9]."

Jan 1, 1990

By C. B. Barmore, B. W. Gandrud, B. M. Bird

"The Bradford mine of the Alabama By-Products Corporation is located in the Warrior coal field of Alabama, in the northern part of Jefferson County, about 25 miles north of Birmingham. The coal mined from the Black Creek bed at this point is not considered to be ideal for coke making by itself but because of its exceptionally low ash content is mixed with the higher-ash coking coals from other beds of the district to control the ash content of coking mixtures. Further reasons for using this coal only as a diluent of the higher-ash opals are that the thinness of the bed renders the production costs relatively high and the reserves are somewhat limited.This paper, which is the fourth of a series on the washability of Alabama coals, Like its predecessors dealing with the Mary Lee beds and the Clark bed,6 contains screen-sizing and float-and-sink tests of a representative sample of the raw coal, and flakiness tests showing the proportions of flaky particles in certain selected sizes. However, inasmuch as the float-and-sink tests of the coarse sizes showed excellent liberation of coal from impurities, crushing tests have not been considered necessary.The data on which this report is based have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods."

Apr 1, 1931

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By IRENE AITKENS

The emerald is the most costly of all gems , due to the scarcity of flawless stones . This fact gave rise to the ancient axiom , " As rare as an emerald without a flaw . The finer gems not only command the highest prices at all times , but when flawless are considered the most highly prized of all gem stones . George F. Kunz divides emeralds into two distinct classes : " Exceptional specimens , " which bring as much as $ 6,000 a carat ; and " fine- quality specimens , " which bring about $ 1,000 a carat .

Jul 1, 1931

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By J. N. Greaves

Investigations were conducted by the U.S. Bureau of Mines to develop flowsheets for the recovery of tungsten and gold from four Alaskan scheelite-bearing ores. Basic gravity concentration and cyanide leach tests were performed on all samples. About 46 pct of the tungsten and 30 pct of the gold from one sample were recovered in a gravity concentrate containing 24 pet W03 (tungstic oxide) and 119 troy ounces per short ton (tr oz/st) Au. Froth flotation of the gravity concentrate resulted in separate tungsten and gold products with grades of 38 pct W03 and 2,720 tr oz/st Au and recoveries of 60 and 97 pet, respectively. Additional gold was recovered from the gravity and flotation tailings by cyanidation. Overall recoveries of tungsten and gold from this sample were 28 and 94 pet, respeetively. A flowsheet with mill design parameters was developed that consisted of (1) free gold and scheelite recovery by gravity methods and froth flotation and (2) fme-grained gold recovery by cyanide leaching of reground gravity and flotation tailings, followed by a carbon-in-pulp (CIP) circuit. Data were developed from the Bond mill work index, gold and tungsten flotation, conventional and high-rate thickening, cyanide leaching, and CIP adsorption tests.

Jan 1, 1989