Search Documents

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By E. J. HOFFMAN, J. c. W. FRAZER

The apparatus and methods described in the following pages were devised and used by the writers in connection with certain investiga- tions of the technologic branch of the United States Geological Sur- vey, especially those bearing on the improvement of furnace condi- tions and on efficiency in the use of fuel. The Bureau of Mines, which has charge of such analyses and tests of fuels as were formerly made by the technologic branch of the Sur- vey, is using the same apparatus and methods in connection with similar investigations that are being carried on at the testing plant of the bureau at Pittsburg, Pa. The furnace conditions prevailing both in small plants and in large industrial establishments in this country are frequently far from satisfactory. If such conditions are to be improved, they must be more thoroughly understood, and means must be found to insure complete combustion of the fuel, and yet to permit operation with such an excess of air as will result in the greatest efficiency. In this work the services of the chemist are indispensable. A very important problem is the determination of the small percentage of unburned combustible matter that escapes from the furnace in the flue gases. Under ordinary circumstances so little as 0.1 per cent of unburned combustible matter in a furnace gas is equivalent to about 1 per cent of the fuel used; and for the determination of such small percentages of gas more accurate and refined methods are required than have ordinarily been available heretofore. It is the purpose of this paper to describe some apparatus and methods which have proved satisfactory to those engaged in the chemical work of the investigations mentioned. While these methods and apparatus have been designed more particularly with regard to analysis of furnace gases, their use is by no means limited to that purpose. The reader will readily see their applicability to other uses in which the sampling and analysis of gases are involved.

Jan 1, 1911

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By L. H. McGuire, L. B. Berger

"During the period October 31 to November 4, 1944, tests were conducted by the Bureau of Mines in the Cascade Tunnel of the Great Northern Railway Cc. to determine the effects upon the tunnel atmosphere of the use of a Diesel freight locomotive through the tunnel. These tests were conducted at the request of the company to ascertain whether undesirable conditions might be caused by the discharge of Diesel engine exhaust gas in the tunnel, which was constructed for an electric haulage system and is not provided with equipment for mechanical ventilation. The use of Diesel locomotives on the division that includes the Cascade Tunnel was under consideration as a means of augmenting haulage facilities for the abnormal freight tonnage that must be handled during wartime.As the Bureau of Mines has received requests for information on the extent of contamination of the air of railroad tunnels by Diesel locomotives, this report was prepared to make available for general information the data obtained during the tests in the Cascade Tunnel. As the test locomotive is of a type used on other railroads, and as the bore and grade of the tunnel and the tonnages moved are comparable to such factors on other roads, the data should be sufficiently representative to be of general interest. The exceptional length of the Cascade Tunnel made it an excellent location for obtaining information on the composition of the tunnel air and on the movement of air induced in the tunnel by the passage of trains.The writers are indebted to C. O. Jenks, vice president of the Great Northern Railway Co., who arranged for the tests, and to the following personnel of the railroad who cooperated in the conduct of the tests: I. E. Clary, superintendent, Spokane Division, J. L. Robson, superintendent of motive power, oil and gas equipment, J. F. N. Gaynor, superintendent of electric operations, William Lowney, master mechanic, Spokane Division, and D. F. Marston and Verne Nelson, assistant superintendents of electric operations.The Cascade Tunnel is on the Spokane Division of the Great Northern Railway and pierces the Cascade Mountains some 49 miles west of Wenatchee, Wash. The west end of this division is electrified from Appleyard Station, 2 miles east of Wenatchee, to Skykomish, Wash., a distance of 73 miles. Until the described tests, only electric haulage had been employed through the tunnel since it was first opened to traffic in January 1929.The Cascade is the longest railroad tunnel in the United States - 7.79 miles. The tunnel is single-track, perfectly straight, concrete-lined, and is on an essentially uniform grade of 1.56 percent, ascending from west to east. The cross-sectional area of the tunnel is 314 square feet, the dimensions being shown in figure 1. Elevation of the east portal is 2,880 feet and of the west portal, 2,240 feet."

Jun 1, 1946

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough so that realistic rate determinations could be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1988

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By D. Harrington

The occurrence of dust in mines has always been a source of trouble, but for any years, and virtually up to the beginning of the present century, relatively little of a definite nature was known as to the numerous ill effects of dust in mining operations. Even today, with the west amount of time given and attention paid (for at least 40 years in various, countries) to research and observation en dust in mining, and in spite of the experience with it, much information remains to be obtained, before definite, well-authenticated statements can be made as to numerous features connected with the occurrence of dust in Dines an of its effect upon the health and safety of the worker. One statement that can be made with relatively good assurance of being uncontradicted in that dust is a real menace to the well-being of mine workers, and this includes both health and safety. In addition, dust in and around mines and mining plants is one cause of large financial losses to mine owners and operators. FORMATION OF DUST IN COAL MINES IN THE UNITED STATES One definition of mining is "the processes by which useful materials are obtained from the earth's crust; " since virtually all of the useful materials of or in the earth's crust either are solids or must be reached by penetrating through solids, the materials that are moved in mining must necessarily be broken or disrupted, so that almost every phase of the work of loosening the material and transporting it is likely to produce dust.

Jan 1, 1939

By W. J. Kroll

This report on the bibliography of zirconium has been confined to those publications and patents that appear to be useful in the commercial development of the metal, both the malleable and the nonmalleable. The methods of production have been stressed and special attention has been given to the alloys. Compounds of importance, like the oxide and chloride, for the manufacture of the metal or of the alloys have been considered. The use of the oxide in refractories anal in the glass and porcelain industries has been omitted. The present survey is critical; that is to say, an attempt has been made to evaluate the effectiveness of suggestions made in the literature. The exhaustive work of Marden and Richy, Bureau of Mines Bulletin 186, published in 1921, has been taken as a base to start from with the intention of bringing the subject up to date with material published in the last 24 years. During this time there was considerable 'advance in the preparation of the metal and Its alloys, and in the development of new uses. On the other hand, there was little progress in the methods of decomposing the ores, so that the chapter on this latter phase is necessarily short.

Jan 1, 1946

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929