Search Documents

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research-(CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. 2/ No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43. the semiannual reports were resumed.

Jan 1, 1950

By M. M. Tilman

The Bureau of Mines conducted research to determine the feasibility of strengthening experimental magnesium-base sheet alloys by strain softening induced by controlled cold rolling followed by selective heat treatment. Relatively small alloying additions having potential for producing strain softening were selected from metals that are readily avail-able. Tensile properties comparable to minimum properties of the most commonly used magnesium-base sheet alloy AZ31B, in the H24 condition (strain-hardened and partially annealed), were obtained in an Mg-IMM (mischmetal)-O.5Mn alloy after strain-softening rolling followed by heat treatment. Tensile properties of the experimental alloys in certain conditions are also compared with minimum tensile properties of other standard magnesium sheet alloys. Incidental to the principal objectives, apparent superplastic behavior was observed in three experimental magnesium-base alloys containing MM, MM plus manganese, and MM plus zirconium.

Jan 1, 1985

By C. Q. Cupps

n view of increased interest in secondary recovery of oil in the Cut Bank field, Montana, a review has been made of unpublished data obtained during a 1943-44 study of reservoir oil characteristics in this field. Considerable uncertainty was attached to interpretations of subsurface oil sample analyses from six Cut Bank zone wells, one Lander sand well, and one Moulton sand well, because of adverse sampling conditions and wide range in the data. Much of this uncertainty has been removed by this review which has shown two of the Cut Bank zone samples and the Moulton sand sample to be representative of the reservoir oils. Estimates of original reservoir oil characteristics derived from differential-liberation analyses of these samples show that the oil in the Cut Bank zone was initially saturated at the gas-oil contact pres-sure, 750 psia, and the oil in the Moulton sand was undersaturated with a saturation pressure of only 380 psia. The rest of the samples were indicated to be nonrepresentative of the reservoir oils because of a disproportional vaporization of heavier components of the solution gas. The vaporization of these components is believed to be a cumulative effect of contact of the oil with bypassing, light-gravity gas which had been liberated at higher pressures from solution in oil farther back in the formation, or which had come from the gas cap, rather than from the singular effect of gas evolution caused by excessively low bottom-hole pressures. Change of oil composition caused by the latter was found to conform closely to that occurring during a differential liberation of gas in the laboratory.

Jan 1, 1967

By C. E. Arrington, A. C. Rice

"Part 1. REDUCTION AND USE OF OXIDANTSSUMMARYA study has been made of the volumetric determination of molybdenum by reduction in the Jones reductor, receiving the reduced solution in a mixture of ferric alum and phosphoric acid, and titrating with standard oxidizing agents. In addition to potassium permanganate, which has long been utilized for this titration, potassium dichromate and ceric sulphate have been found to be applicable. The latter oxidants have been found to be especially useful in the form of dilute solutions for the determination of small amounts of molybdenum. The tests revealed that certain internal indicators give excellent results in these titrations.Reason for These ExperimentsThe following study was initiated with the hope of providing the mining and metallurgical industries with an accurate and rapid technical method for the determination of molybdenum in such low-grade materials as ores, rocks, tailings, steels, and alloys containing less than 0.3 percent molybdenum. Although the experimental work was designed with this purpose in mind, many of the results are applicable to material containing a higher percentage of molybdenum.While the Bureau of Mines had an experiment station in Colorado, considerable analytical work was done on what were then (up to about 1923) classed as rare metals. One of these was molybdenum; and in Bulletin 212, Bonardi's (1) 3/ 60-page chapter covered all methods for the analysis of molybdenum."

Apr 1, 1939

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970

By W. A. Stickney, J. W. Town

Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .

Jan 1, 1964

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By R. F. Kendall

Only a limited number of mass and infrared reference spectra of high purity unsaturated hydrocarbons and oxygenates are presently available in the literature. To aid Bureau of Mines research programs requiring such references, 64 mass spectra and 70 infrared spectra were obtained and are reported. The individual compounds, acquired from commercial sources, were purified by preparatory gas chromatography. Purity determinations were made using a combination of analytical gas chromatography, microhydrogenation, and catalytic deoxygenation. These spectra will aid spectroscopists in the identification of compounds of the types reported.

Jan 1, 1966

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

By Rexford D. Singer

The purpose of this study was to evaluate the current literature on the use of calcium chloride and ligninsulfonates as dust suppressants with respect to potential adverse effects on health or the environment. Calcium chloride poses little internal hazard to man and animals, but toxicity to vegetation in and around the area of application should be expected. The effects, however, should be considerably less than those observed from using calcium chloride as a road deicer. Except for trout, ligninsulfonates seem to pose little direct systemic toxicity problems in aquatic organisms, animals and man or any problem with local vegetation. Because of a greater volume of information on its use and effects, calcium chloride is recommended over ligninsulfonates.

Jan 1, 1982

By W. H. Frederic, F. H. Gibson, R. F. Abernethy

This publication contains the quantitative values for phosphorus , chlorine , sodium , and potassium in United States coals . The samples tested were taken from commercial shipments and have been selected to represent the principal coal producing areas of the country . Due to combining the analytical results from two separate surveys , values for the four elements are not available for all samples .

Jan 1, 1965

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements on solutions and isolated powders provide direct evidence for the involvement of Cr(V) species in the reduction of Cr(VI) by NAD(P)H. ESR analysis of an isolated Cr(V)NAD( P)H solid yields 6 11 = 1.9831 and 6.i. = 1.9772, indicating that the unpaired electron occupies the d22 orbital of the Cr(V) ion, with square-pyramidal geometry. Addition of hydrogen peroxide (H2 0 2 ) to the N AD(P)HCr( VI) reaction mixtures suppresses the Cr(V) species and generates hydroxyl (""OH) radicals. The ""OH radicals were detected via ESR spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide and a-(4-pyridyl-1- oxide)-N-tert-butylnitrone as spin traps. The dependence of Cr(V) and ""OH radical formation on the H20 2 and Cr(VI) concentrations indicates that the Cr(V) species react with H20 2 to generate the ""OH radicals. Similar results were obtained by using various diols (arabinose, cellobiose, FAD, fructose, glyceraldehyde, ribose, and tartaric acid), a-hydroxycarboxylic acids, and glutathione. Investigations with superoxide dismutase showed no significant participation of 02 in the generation of OH radicals. These results thus indicate that the Cr(V) complexes, produced in the reduction of Cr(VI) by cellular reductants, react with H20 2 to generate ""OH radicals, which might be the initiators of the primary events in the Cr(VI) cytotoxicity.In this paper we report an electron spin resonance (ESR)3 spectroscopic detection of Cr(V) species in the reduction of potassium dichromate, henceforth called Cr(VI), by NAD(P)H and other diols. Also reported here is the detection of the hydroxyl (""OH) radical in the reaction between hydrogen peroxide (H2O 2) and a variety of Cr(V) complexes. This work was undertaken because while the reduction of Cr(VI) to lower oxidation states has been suggested as a key step m the mechanism of Cr(VI) toxicity, mutagenicity, and DNA alteration, the details are not yet clear (1-5).Earlier studies on the mechanism of Cr(VI) reduction in cellular systems include those on the reduction of chromate by microsomes (6-8), rat liver DT-diaphorase (9), and aldehyde oxidase (10). All these studies imply that Cr(VI) can be reduced to Cr(Ill) by cellular constituents. Regarding the mechanism of Cr(Vl) carcinogenicity, Jennette postulated that Cr(V) is the ultimate carcinogenic form of chromium compounds (8). This conclusion has led to many further investigations of the formation of Cr(V) in the reduction of Cr(VI) under biologically relevant conditions (11-33). More recently, however, Kawanishi and co-workers (34) have investigated the mechanism of DNA cleavage induced by Cr(VI) in the presence of H20 2 and have argued that it is not Cr(V) itself that is carcinogenic, but it is the reactive oxygenated species (02, 10 2 , ""OH) (produced by the decomposition of the Crv(02) ¾ - ion) that cause the DNA alteration."

Jan 1, 1990

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988