Search Documents

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By David Schlain

IN 1942 the Bureau of Mines began to develop the Kroll process for use in the large-scale production of titanium. Titanium and titanium alloys are now commercial metals. These metals are relatively expensive, but It is now evident that they will have important industrial uses and that in many instances these will be related to their remarkable corrosion resistance. This bulletin presents the known corrosion properties of titanium and its alloys in useful form. In marine environments titanium is highly resistant to corrosion and does not pit, or undergo crevice corrosion, stress corrosion, or corrosion fatigue. Titanium is also highly resistant in many salt solutions, including most chlorides. It is very resistant to corrosion in nitric acid solutions. It is also resistant to white fuming nitric acid. However, it may react violently with red fuming nitric acid. In phosphoric acid solutions titanium has rela¬tively good resistance to corrosion, but it has less resistance to sulfuric acid and still less to hydrochloric acid solutions. Titanium corrodes very rapidly in hydrofluoric acid Solutions. It is very resistant to corrosion in many organic chemicals. However, it has only moderate resistance to formic acid solutions and poor resistance inn oxalic acid solutions. Titanium does not corrode in dichloroaretic acid but, corrodes rapidly in 100 percent trichloroacetic acid at 100° C. Titanium is resistant to barium, calcium, magnesium, ammonium, and sodium hydroxides. Titanium is inert in wet chlorine, bromine, or iodine gases. However, in dry chlorine gas titanium reacts rapidly enough to ignite. It also reacts rapidly with dry bromine gas, but, it is resistant to dry iodine gas. When titanium is exposed to red fuming nitric acid solutions with high nitrogen dioxide content and low water content, it corrodes, undergoes stress-corrosion cracking, and becomes pyrophoric. This occurs more readily with some titanium alleys, such as titanium-8 percent manganese. A fresh titanium surface immersed in water or in an aqueous solution and in contact with an oxygen-rich atmosphere under sufficientt pressure is unstable and will ignite spontaneously. Inherently an active metal, titanium has a tendency to become less active in environments containing oxidizing agents such as air, oxygen, chlorine, or ferric, cupric, or platinic ions. Titanium is more noble than most structural metals in roost, environments and its excellent corrosion resistance is generally not, affected by contact with these metals. However, some of the other metals corrode faster because of contact with titanium. Titanium undergoes anodic polarization readily, so that even when it is the less noble member of a galvanic couple it may corrode less because of the contact. Titanium alloys often have corrosion properties and electrochemical characteristics similar to those of commercially pure titanium. Titanium alloys containing noble metals, zirconium, molybdenum, vanadium, tantalum, or copper sometimes have better corrosion resistance than pure titanium.

Jan 1, 1964

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930

The mineral chromate is the sole current source of commercial chromium Chromite varies compositionally within limits permitted by the formula ((Mg,Fe,Zn,Mn)(A1,Cr)2O4) No chromate has been mined in the United States since 1961 In the past, almost all the chromate mined in the United States came from Alaska, California, Maryland, Montana, Oregon, and Pennsylvania, with about one-half of all production coming from Montana Primary chromate deposits occur only in certain kinds of ultramafic or closely related anorthositic rocks The two major types are stratiform (layered) and pod-shaped The Stillwater Complex of Montana is the largest known United States resource It is a stratiform deposit where several exposed zones of high-iron chromiferous material extend in length Since there is no commercial chromate mining in the United States, there are no environmental problems related to underground mining

Jan 1, 1975

By H. R. Wells

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. However, the comparatively low grade and small size of the known ore bodies, the small demand for cobalt, and. the lack of adequate roads throughout the region precluded extensive exploration of the early discoveries in the area. Recent advances in alloy metallurgy, accentuated by wartime activities, greatly increased the demand for sources of domestic cobalt. Beginning In 1941, engineers of the Bureau of Mines conducted an examination and exploration program in the Blackbird district. This work was supplemented by an exploration program by engineers of the Howe Sound Mining Co., 730 Fifth Ave., New York 19, N.Y.

Jan 1, 1948

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

By S. H. Ash

A CLAY, sand, and gravel deposit known as the "buried valley" of the Susquehanna River is situated in the Northern field of the anthracite region of Pennsylvania near Wilkes-Barre. The presence of this buried valley and the uncertainty regarding the extent and physical condition of the water-bearing valley-fill deposits have made great care necessary in mining operations to avoid breaking the strata between the mine workings and the valley-fill deposits to the extent that inundation of the mine workings would follow. The principal factor that threatens to cut short the life of the anthracite industry, to curtail production, and to affect the economic structure of the people and business dependent on anthracite for their livelihood is inundation of anthracite mines (6,7).3

Jan 1, 1950

By L. C. Brichta

The Melrose zinc-lead. deposit is in an area of structural disturbance of sedimentary rocks in the Melrose mining district in Cherokee County, Kans., 25 miles west of Joplin, Mo., adjacent to the northwest limits of the Tri-State district. Mining and milling in the Melrose district has been sporadic and. very limited, largely due to the high cost of exploration through great thicknesses of barren rock, 350 to 440 feet overlying the ore deposits. No mining has ever been done on the Melrose zinc-lead tract, but it has been drilled extensively. The drill-hole logy indicate extensive structural deformation, silicification, and zinc-lead deposits in the Boone limestone-chert formations of the Mississippian series, which is overlain by thick-bedded Pennsylvanian shale and sandstone. Analyses of samples from Bureau of Mines drilling indicate the ore minerals are sphalerite and galena with no evident oxidation. During the period from November 2, 1949, to March 13, 1950, the Bureau of Mines investigated the deposit by churn drilling and sampling 23 holes aggregating 10,405 feet of bore. Factual data on the investigation and logs of holes drilled by private parties and the Bureau of Mines are presented in this report.

Jan 1, 1951

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines' studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this con¬dition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

By H. D. Jacobs

A process for recovering both iron and manganese from four manganiferous ores of the Cuyuna Range was evaluated. It comprised: (1) Low-temperature gaseous reduction to convert nonmagnetic iron minerals to magnetite and manganic minerals to manganous oxide, (2) acid leaching to extract manganese, and (3) magnetic separation to reclaim iron from the leach residue. Iron recoveries from the magnetic products ranged from 70 percent to 90 percent; manganese recoveries from leach filtrates ranged from 75 percent to 95 percent. Two ores, from the Hillcrest and South Alstead properties, yielded magnetic products considered adequate for use as blast furnace feed. Although good yields of manganese were attained on all ores, appreciable iron accompanied the manganese into solution. Previous work, however, has shown that this iron can be precipitated almost quantitatively under autoclave oxygen pressure with very little loss of manganese.

Jan 1, 1970

By S. H. Ash

THE MAGNITUDE of the anthracite industry's drainage problem in the Northern field of Pennsylvania is realized when it is known that, for the 8-year period 1944-51, all pumping plants in this region pumped an average volume of 112.5 billion gallons of water from the mines to the surface each year. This is over 214,000 gallons per minute pumped against an average hydrostatic head of 400 feet each year for that period (12).4 By comparison, Lake Wallenpaupack, the largest artificial body of water lying wholly in Pennsylvania, contains 71 billion gallons of water in its 24-square-mile area; the average volume of water pumped from the mines in the Northern field each year during the 8-year period was 58 percent more than the volume impounded in Lake Wallenpaupack. The natural configuration of the drainage area overlying the Northern field subdivides the total area into two major drainage areas-the Lackawanna River drainage area and the Susquehanna River drainage area overlying the Wyoming Basin. Although the 169-square-mile drainage area overlying the Wyoming Basin is slightly less than half that of the Lackawanna River drainage area (10), the total volume of water pumped to the surface from mines in the Wyoming Basin is 21 percent more than the total volume pumped to the surface from mines in the Lackawanna Basin. From this, it is apparent that the Susquehanna River and the pervious deposits in the buried valley over which it flows in its course across the coal measures of Wyoming Valley is the greatest single source of mine water affecting mines in this area. Because of its relatively flat terrain, the wide flood plain of Wyoming Valley does not facilitate rapid runoff; consequently, much of the surface water seeps directly into the buried-valley deposits and eventually into the mine workings.

Jan 1, 1953