Search Documents

By Sarkis G. Ampian

Extraction of alumina was correlated with the sinter and leach products from the lime soda sinter process for anorthosite. The effect of composition and grain size of reactants, time and temperature of sintering, and techniques of sample preparation were investigated. Greater than 90 percent Al2O3 extractions were obtained from dry-mixed minus 200-mesh anorthosite sinter mixes having mole ratios of CaO/SiO2 = 1.8 and Na2O/Al2O3 = 0.8. These sinter mixes were briquetted at 15,000 psi and fired between 1,200° C and 1,320° C for 20 to 60 minutes. The sinter phases that contribute to low alumina recovery were determined by X-ray diffractometry, optical microscopy, and electron probe X-ray spectrography. The mechanism of the sintering reaction was investigated by high-temperature X-ray diffractometry. The contrast in the lime soda sinter process for clays and for anorthosites are discussed. Explanations and suggested solutions are presented for problems such as gelation and variable alumina recovery encountered by previous investigations.

Jan 1, 1967

By S. H. Ash

The Pennsylvania anthracite region is composed of four fields, namely, the Northern, Eastern Middle, Western Middle, and Southern. It is in the eastern part of Pennsylvania and is shown on figure 1. The anthracite industry is confronted with a crucial problem of inundation by water impounded in underground pools in many mines and by infiltration of water from streams and pools on the surface (3). The deposits of anthracite in the United States are limited virtually to Pennsylvania, and the difficulties of this industry have been commonly considered as a State problem rather than a national one (1, 4, 6, 7). Anthracite was discovered in Pennsylvania in 1762, and the first mining company was formed in 1793. It was not until 1812 that anthracite began to receive recognition in the Philadelphia market as a domestic fuel, and by 1838 the annual production was nearly 1 million net tons. Since anthracite mining began, mine water has become progressively more difficult and costly to handle because of the extraction of anthracite both underground and along the outcrops of the beds, until at the present time mine drainage is a major anthracite-mining problem. Mine water is handled at the anthracite mines as follows: (a) by pumping, (b) by drainage tunnels, (c) by combination of pumping and drainage tunnels, and (d) by water hoists (hoisting water by means of large buckets) (4, 5,6, 7). This paper covers removal of the water from mines by means of pumping plants. Pumping is indispensable in the production of anthracite (5). The cost of pumping mine water has increased progressively since anthracite mining began. Some collieries have been forced to discontinue mining because of the high cost of pumping.

Jan 1, 1950

By Charles Vaught, Henry J. Kellner, Michael J. Brnich, Henry P. Cole, William J. Wiehagen

In 1985, U.S. Bureau of Mines and University of Kentucky researchers began a series of studies relating to self-contained self-rescuer (SCSR) donning proficiency. During the next 5 years investigators examined a number of factors that have a bearing upon miners' ability to put on and use the apparatus in an emergency: the procedure being taught; availability and utilization of training models; opportunities to practice; hygiene; and on-the-job training. This report presents an overview of that research. It is concluded that companies should adopt a hands-on training protocol that allows them to integrate SCSR donning practice into other workplace routines such as fire drills.

Jan 1, 1993

Note: This is a progress report and therefore not necessarily conclusive. Further data may result in conclusions somewhat different from those reported here. Crop Growing Season The monthly average temperatures, total precipitation, and evaporation for the demonstration mine are shown in Table 1. [ ]

Jan 1, 1980

By Charles W. Perdue

This U.S. Bureau of Mines report considers, from a psychological perspective, the perceptual process by which miners recognize and respond to mining hazards. It proposes that if the hazard recognition skills of miners can be improved, mining accidents may be reduced to a significant degree. Prior studies of hazard perception in mining are considered, as are relevant studies from investigations of military target identification, pilot and gunnery officer training, transportation safety, automobile operator behavior, research into sensory functioning and visual information processing. A general model of perception is introduced, and selected concepts from the psychology of perception that are applicable to the detection of mining hazards are reviewed. Hazard recognition is discussed as a function of the perceptual cues available to the miner as well as the cognitive resources and strategies employed by the miner. The development of expertise in responding to hazards is related to individual differences in the experience, aptitude, and personality of the worker. Potential applications to miner safety and training are presented.

Jan 1, 1995

By William J. Campbell

This study was a part of two programs: The first, to develop and evaluate high-temperature refractories; the second, to investigate reaction-rate kinetics and phase equilibria in the sinter step of the lime-soda process for the recovery of alumina. High-temperature X-ray diffractometer techniques are to be used extensively in both programs. This paper summarizes developments in the field of high-temperature X-ray diffractometers through 1959, evaluates various furnace designs, and describes briefly the X-ray diffraction facilities of the Federal Bureau of Mines. A more detailed description of the equipment and its calibration is planned in a future paper on thermal expansion and phase inversion of rare-earth oxides.

Jan 1, 1961

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By D. A. Reynolds

THIS REPORT gives results of an investigation of the carbonizing properties of two Tennessee coals, one from the Jellico bed in Campbell County and the other from the Sewanee bed in Marion County. Jellico coal and blends with 20 and 30 percent Pocahontas No. 3 coal were carbonized at 800° and 900° C. by the BM-AGA method. Sewanee coal was carbonized by the same method at 800°, 900°, and 1,000° C.; blends with coals of similar and different ranks were carbonized at 800° and 900° C. The coals were subjected to various physical and chemical tests, including complete chemical analyses, low-temperature assays, and agglutinating, free-swelling, friability, plasticity, and expansion tests. The Tennessee coal field is a part of the Appalachian field, which extends from northern Pennsylvania to central Alabama. The Jelico bed, one of the most important in the State, is part of the Jellico formation, which is above the Lee formation of the Lower Pottsville. Sewanee coal bed belongs to the Sewanee conglomerate and is stratigraphically lower than the Jellico bed.

Jan 1, 1953

By D. S. Kingery

Experiments initiated by the Bureau of Mines on August 26. 1969, and recent work of others, have demonstrated the effectiveness of ventilation for controlling concentrations of respirable coal mine dust. Substantial reductions in dust concentrations have been attained by increasing the volume and rate of air movement across the face and by controlling the airflow pattern. Ventilation experiments conducted by the Bureau using high-pressure fans as auxiliary ventilation units showed that lace-generated dust could he effectively controlled in five mines employing continuous mining machines. Additional data was obtained on industry installations in two mines using similar ventilation systems. By maintaining an airflow approaching 100 fpm across the entry, the experimental system reduced the concentration of respirable dust by factors as great as 6.4. In all mines where the system was used the face-generated dust concentrations were reduced to below 3 mg/m3. Total respirable dust in two cases was above the 3 mg/m value because of the dust content of the intake air. In some mines. depending upon the type of coal being mined and other dust control factors in use, it was possible to Obtain concentrations of less than 2 mg/m Although the technology for the application of the dust control system investigated is readily available, it is evident that additional engineering studies should he made in each mine where the system is to be applied.

Jan 1, 1969

By E. J. Gleim

In the mining of coal the trend is toward more and more mechanization. This increased use of machinery to replace hand labor is assuming many new forms and presents a constantly changing aspect. Safety engineers must be alert if the many electrical problems resulting from these new installations are to be handled safely. Some of these problems present possible electrical hazards that may be overlooked by the safety engineer unless they are called to his attention by one who has made a special study of the conditions. The foregoing is especially true of conveyor systems of mining. The terms "conveyor systems" and "conveyor mining" as used in this paper refer to those systems in which various types of conveyors are employed to transport coal away from the working place. In some mines this means complete elimination of track, cars, and locomotives. In others it means that conveyors take the coal from the working place to a convenient loading point, from which transportation is completed by cars and locomotives.

Jan 1, 1941

By Walter E. Lewis

The Cuyuna iron range in Crow Wing County, Minn., is the principal producer of manganiferous iron ore in the United States. The ore is mined from a manganiferous iron formation in the bedrock of the Cuyuna district. This iron formation is divided into two general lithologic types-thin-bedded and thick-bedded. The unoxidized, thin-bedded iron formation is composed of iron silicate with associated fine-grained carbonates of iron and manganese. The thick-bedded iron formation carries iron and manganese oxides with intimately associated silica. Oxidation and leaching of the original iron formation have been the most influential factors in producing manganiferous iron-ore concentrations in quantities large enough to exploit on a commercial basis. The unoxidized and the partly oxidized and enriched iron-formation materials are suitable as a source of ferrograde manganese ore. These materials have been classified according to their amenability to mineral dressing and degree of oxidation and leaching.

Jan 1, 1958

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Alton B. Cook

In the Scurry Reef field, Scurry County, Tex., a study was made to determine the physical properties of the oil in all parts of the reservoir by a new method developed for this study. The method involved correlation of data from a survey 1 of the gravity of the produced oil, from measurements of gas-oil ratios on key wells selected to give representative data for the entire reservoir, and from laboratory analyses of reservoir oil samples. A field survey was made of the API gravities of the produced oil by testing oil samples from 107 key wells. Precise gas-oil-ratio tests were made on 45 key wells that were producing under comparable separator-operating conditions. Subsurface-oil samples were obtained from seven wells, selected to provide reservoir oils ranging approximately from a minimum to a maximum in saturation pressure. The physical properties of the subsurface-oil samples were determined, and correlations were made of these laboratory data with the field gas-oil-ratio test data. These correlations were then used to estimate physical properties of the oil throughout the reservoir. A logical procedure of determining the variations in physical properties of reservoir oils in most fields is to obtain and analyze subsurface-oil samples from enough key wells to provide an ample coverage of the field. Under this procedure, data from a large number of samples would be needed to provide the desired information on the Scurry Reef field, as it is one of the largest known in the United States.

Jan 1, 1955

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated an ammoniacal sulfate leach process for recovering nickel and cobalt from low-grade domestic laterites. Solvent extraction of cobalt, one of the process steps, requires the reduction of hexammine complexes of C03+ to C02+ in an ammo-niacal leach solution. Previously, reduction was accomplished using cobalt metal shot in a column. This report presents experimental results and an economic evaluation comparing two alternate techniques with the shot column: (1) an electrolytic reduction cell with an extended surface area cathode and (2) direct electrowinning from purified leach solution using a cell with a fluid bed cathode. The second alternative eliminates the conventional solvent extraction-electrowinning steps. The costs of the three methods, based on the requirements of a pro-posed commercial-sized plant, including all unit operations, were deter-mined by the Bureau's process evaluation group. The operating costs for the shot column, $1.19/kg Co, and for electrolytic reduction, $1.20/kg, are essentially the same, but the cost of direct electrowinning, $3.77/ kg Co, would eliminate this method as a practical alternative. The cap-ital cost of approximately $14.4 million for reduction in a shot column is much higher than the approximately $4.4 million for electroreduction.

Jan 1, 1985

By W. M. Mark

This investigation was undertaken to develop methods to improve the quality of titanium sponge produced by the Bureau of Mines modification of the Kroll magnesium reduction process. Research revealed that by systematic elimination of detrimental impurities introduced with the raw materials and by improved handling and processing techniques, high-quality ductile titanium with a hardness of less than 110 B.h.n. (Brinell hardness number) can be produced consistently. This improvement was accomplished by helium (or argon) stripping of residual atmospheric and other dissolved gases from the titanic chloride, preliminary dehydration of crude titanium sponge, and careful regulation of the titanium tetrachloride (TiC14) feed rate to the reactors.

Jan 1, 1960

By R. Y. Williams

In this report an attempt is made to discuss the first cost of each of several types of mine-ventilation stoppings, as well as the total annual expense of maintaining a stopping during its required period of service. Such data furnish a basis for comparison of the efficiency of the different types, and are of great importance to an engineer planning the development of a mine. The data given were obtained through an investigation conducted under a cooperative agreement between the Bureau of Mines, the Illinois State Geological Survey, and the department of mining engineering of the University of Illinois. The report itself is published by the Bureau of Mines as a contribution to the literature on safety and efficiency in coal mining.

Jan 1, 1915

By John B. Goodman

A LOW-TEMPERATURE carbonization assay test is described, and factual data derived from this test are presented. The test procedure outlined in this report incorporates a mild-steel retort of improved design, an accurately controlled method of heating, and a complete collection and condensation system for the solid, liquid, and gaseous products of carbonization. The test described establishes, under closely controlled conditions, the relationship of temperature to yields of products on carbonization. Noncoking or weakly coking coals and other carbonaceous material are particularly amenable to testing by the assay. Mass balances of 100 percent± 0.3 are obtainable by this test. It is believed that the efficiency of the test and the accuracy of the type data obtained have been materially increased.

Jan 1, 1953

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By J. J. deBarbadillo

This Bureau of Mines report describes a process for recovering chromium and other metals from superalloy scrap. Laboratory-scale experiments were conducted to test a complex flowsheet utilizing a wide range of extractive metallurgical operations. The novel basis for the process is the fonnation of a sulfide matte in which chromium is concentrated in a discrete chromium sulfide phase. Mineral processing and hydrometallurgical procedures are used to separate chromium sulfide from the other matte constituents. The products of the process are a chromium-nickel alloy suitable for reuse in the superalloy industry, electrolytic nickel, electrolytic cobalt, and iron-molybdenum residue. Recovery of the principal elements contained in the scrap is chromium--93 percent, nickel--99 percent, cobalt--96 percent, and molybdenum--92 percent.

Jan 1, 1981