Search Documents

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By A. Vishwakarma, V. Himanshu, K. Dey

Underground mining is the most feasible method after extinction of shallow depth ore deposits. Longhole stoping method is the most technically advanced method for the faster excavation. In this method, the holes are drilled in the form of ring pattern and explosives are used for the rock breakage. During blasting, the explosive energy sometimes also breaks the non-ore material. The non-ore material gets included in the extracted ore and enhances the ore dilution. Few uncontrollable factors which affects the ore dilution are ore body characteristics, rock quality, insitu stress condition etc. Apart from uncontrollable factors, explosive energy and blast design also plays an immense role in ore dilution. In the blasting practice, the purpose is to effectively utilise the explosive energy for rock breakage. The optimum delay is required so that the blast holes attain adequate free face before the blasting. This paper deals with the optimisation of blast design parameters to reduce ore dilution in underground hard rock mining having narrow vein. The study was carried out using numerical simulation. The explicit dynamics based modeller of Ansys was used for this purpose. The parametric variations in the models were done to optimise the parameters. The burden has been optimised first by varying the width of the narrow vein. The blasts of a ring consisting of single hole were conducted in the model by varying the width of the narrow vein. The damage contour under different parametric variations were analysed. The experimental trial has been also carried out at Zawar Group of Mine, Rajasthan, India. The optimum parameter was decided based on the result of experimental trial and numerical simulation model. The output of the model shows that optimum burden for 3.5 m narrow vein width is 1.12 m and for 1.0 m, it is 1.54 m. This shows that the optimised burden is higher in the vein having lesser width as compared to the greater width. The presence of joints/changed media/interface (between the sidewall and narrow vein) is the major reason behind this. The wave gets reflected back very fast on coming in contact with joints in a 1.0 m narrow vein as compared to a 4.0 m narrow vein. This will quickly convert the compressive wave into tensile wave giving rise to tensile slabbing. Hence proper utilisation of explosive energy will take place for the breakage of rock mass when the width of the narrow vein is smaller. The burden obtained from the experimental trial and numerical simulation models is less than 2.0 %. Hence the numerical simulation based approach can be used for the assessment of the optimum burden for ring blasting in narrow vein under different geomining conditions. This helped in reducing ore dilution and maximization of ore recovery. In the future, empirical relationships may be developed by considering different geological discontinuity, the strength of the rock mass and explosive parameters.

Jan 1, 2024

By David Porter, Nathan Rouse

The implementation of presplit perimeter control in underground mining as a method to decrease dilution yields positive benefits throughout the current and future mining cycles. A case study to understand the benefits of reducing overbreak and underbreak in a cut and fill mining cycle was performed to quantify the reduction in backbreak. The study was performed in a control section of the mine where a presplit perimeter control design was utilized for a length of heading. This control heading was then compared to the existing standard blasting design within the same mining zone. The comparison included multiple aspects of the mining advance including overbreak, dilution of waste, dilution of Cemented Rock Fill, bolt counts, and cycle times. Once mining in the control section was completed and mining commenced in adjacent headings, blast damage due to blast design could be quantified.

Feb 6, 2023

By Stephen G. Rieben

Almost everyone has at least heard of the two one-call systems which serve New England. They are "Call Before You Dig", which covers Connecticut, and "Dig Safe", which covers the remaining five New England states. Those of you who are more familiar with these programs know that it is our job to help guard against the accidental dig-ups of buried plant and to prevent facility service disruptions. We cover all types of buried facilities, from cable television to high pressure gas transmissions lines, telephone cables, electric facilities, fiber optics and everything in between

Jan 1, 1990

By Claudio Lechuga, Carlos Scherpenisse, Juan Rafael Otaiza

From the analysis of drilling process, Block Model information, drilling pattern data and expected fragmentation targets; GBlast® software optimizes the explosive charge design in order to standardize the particle size of each blast.

Feb 1, 2020

By Martin Reed, John Wright

Blasters with the United States Antarctic Program (USAP) have developed techniques for opening access holes in floating sea-ice where the use of conventional drilling equipment is impractical. The blasting techniques have proven successful in sea-ice ranging from 8 to 15 feet thick. Previous published work has treated in detail blasting holes in floating ice from 2 to 6 feet thick.

Jan 1, 2001

By Rick Lamkie

When investigating citizen complaints about blast vibration and airblast, it is important to be able to establish the spatial relationships between blasts, blasting seismographs monitoring the events, and complainant structures to assess any directional impacts. The Pennsylvania Department of Environmental Protection (DEP) routinely uses hand-held GPS receivers to document these relationships. The waypoint (structures and seismograph monitoring locations) and tracking (blasting and permit areas) features are used to map a site. These data are imported into the software for editing and conversion to GPS Exchange (.gpx) format.

Jan 1, 2008

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By E. Vilaescusa, J. Eloranta

The work presented in this paper investigates the influence of non-ideal detonation characteristics related to the blasthole diameter, base emulsion sensitivity (micro-balloon sensitised versus unsensitised) and percent emulsion on the explosive shock energy available to break rock using ANFOemulsion blends. A series of theoretical equal powder factor bench blasting patterns with hole diameters of 127mm (5”), 140mm (5.5”), 152mm (6”) and 165mm (6.5”) are compared to assess the non-ideal confined shock-state work energies. The Non-Ideal Shock Energy Factor (NSEF), which is the available shock energy per cubic meter of blasted material (MJ/m3) or kilocalories per cubic yard (kcal/yd3), is used to compare the different blasting patterns charged with a range of ANFO-emulsion blends from zero to 50% emulsion.

Jan 1, 2012

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Neal Lee, Braden T. Lusk, Brendan McCray

"Selection of a blasting agent for optimum performance is based on many variables. Often, a decision is made with regard to product cost and field testing. Defining optimum performance can be difficult, since downstream effects of fragmentation on loading, haulage, processing, and energy consumption are not immediately clear. Many operations are beginning to optimize their blasting programs “on the bench,” by utilizing information generated downstream at the loader and/or crusher. During the evaluation of a blasting agent, factors such as velocity of detonation, gas production, and sensitivity are typicallyconsidered. Alternatively, brisance (“the shattering power of an explosive material distinguished from its total work capacity”1) is not. Brisance affects the immediate area surrounding a borehole. Fractures produced here during the shock phase of detonation are believed to have an important effect on rock movement and fragmentation. "

Jan 1, 2017

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By Jorge Cárdenas, Gustavo Huerta, Regina Rocha Oriundo, Miguel Angel Humpire, Johan Salas Flores

Currently a critical activity for slopes stability and safety in mining is pre-split blasting to reduce damage from trim blast. Most common explosive used are based on packaged explosives, with 1 ½ in diameter cartridges initiated by detonating cord. Traditional loading process requires a significant amount of trained personnel, which in our application context could take up to 20 blasters. When pre-split blast is scheduled, it usually reduces the availability of the blasters on the total loading services at site which are also demanded to have production blasting ready at same 12-hour shift daylight time.

Feb 6, 2023

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023