Search Documents

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Matheson and Miller

Does anyone have any definitive information on vibration limits for damage to well casings near blasting? Also, are people using self-imposed limits when approaching cased wells? I can only tell you what I have personally done with success. Often in new construction in hard rock, the well is drilled before the foundation is excavated and before the ditch for the water line is excavated. These both require drilling and blasting. Under these circumstances when blasting for the ditch for the waterline we will drill right up to within 10 inches (not feet) of the well casing. We drill line holes the width of the ditch, then about a foot from this, another row of trim holes then as we move away from the casing holes for 1 1/4 inch stick powder for about three rows then as we get further still, we can load with ANFO. I do not have vibration data for this but my experience has been that as long as you are not displacing the material into the casing that no damage is done. These typically are steel casings for residential water service.

Jan 1, 2010

By Benjamín Cebrián, David Flores, María Rocha Gil

This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

Feb 1, 2020

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The emergence of electronic detonators as viable products for use in production mine blasting has enabled mining professionals to rethink the traditional blast design methodologies that pertain to timing. In many ways, electronic detonators can allow great advances in productivity, cost effectiveness, fragmentation, and safety. There are a number of commercially available systems that enable users to program delay times, usually in one-millisecond intervals, according to design decisions. While manufacturers have performed internal studies pertaining to the accuracy of these systems, an independent study quantifying the accuracy of the systems has not been completed to date. The mining industry is in the business of production and any quality control endeavors to independently confirm the accuracy studies performed by the manufacturers would only detract from their bottom lines. Furthermore, limited information is available concerning the accuracy of modern pyrotechnic delay based detonators. In 1985, the Bureau of mines completed a study of three manufacturers’ electric millisecond delay detonators (Bajpayee, 1985). This was the most recent extensive independent study performed on detonators, which unitized pyrotechnic delays, from numerous manufacturers. Advances in the manufacturing process for pyrotechnic delays may have increased the accuracy of detonators using these technologies in recent years. It is commonly accepted that electronic detonators are more accurate than both shock tube type non-electric as well as electric detonators, but the relative accuracy was not objectively and adequately quantified.

Jan 1, 2011

By Francisca Tapia, Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Manriquez, Luis Martínez, Juan Navarro

Efficient energy transmission is critical for effective rock fragmentation in open-pit blasting. However, in zones with highly fractured or soft rock, mismatches in acoustic impedance between the explosive and the rock can lead to significant energy loss. These mismatches reduce fragmentation efficiency and, when energy input is increased to compensate, can trigger unintended side effects such as NOx fume generation. This paper presents a novel methodology that integrates the Fragment Size Energy Fan model with acoustic impedance theory to dynamically optimize explosive energy delivery. A redefined impedance formulation captures volumetric energy transfer and enables the calculation of a Rock Impedance Factor (RIF), calibrated through non-linear regression. To operationalize the model, rock impedance is estimated using the X-4Traits Model—a meta-learning algorithm that interprets Measurement While Drilling (MWD) data from both autonomous and manually operated drills to produce high-resolution, spatially distributed impedance maps. The methodology was calibrated and applied at Minera Escondida Limitada (MEL), using data from over 218,447 blastholes and 526 blasts. Two case studies illustrate its application: Expansion 1 demonstrates improved fragmentation consistency and a 10.7% reduction in powder factor by aligning explosive energy with local impedance variations; Expansion 2 highlights the model’s utility in managing NOx emissions in fractured zones by optimizing energy distribution and confinement without compromising fragmentation. This impedance-based framework provides a robust tool for improving fragmentation outcomes, optimizing energy use, and enhancing control in geologically variable blasting environments.

Jan 26, 2026

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Svatopluk Zeman, Zbynek Akstein, Jiri Pachman, Ahmed Elbeih, Marcela Jungova

BCHMX (cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole or Bicyclo-HMX) was studied as an energetic component of three different plastic explosives based on three matrices: C4 matrix, semtex10 matrix and silicone matrix. The original plastic explosives, Composition C4 - based on RDX (1,3,5-trinitro-1,3,5-triazinane), Semtex 10 explosive based on PETN (pentaerythritoltetranitrate) and plastic RDX-silicone, were included for comparison. Sensitivity and performance parameters were studied.

Jan 1, 2011

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009

By Dr. Calvin J. Konya, Anthony Konya

Beginning on the Niagara Power Project, presplitting became a widely used blasting technique to obtain smooth walls in mining and construction projects reducing scaling, creating more stable pits, allowing the application of slope steepening to reduce waste removal and increase mining depths, and increasing the safety of mine and construction workers. This technique has been minimally studied in comparison to production blasting and currently two separate theories are present on the mechanics behind the presplit. The first is that shockwave collisions between boreholes cause a tension zone to develop causing the split formation. The second is that gas pressures build in the boreholes causing hoop stresses between holes leading to a presplit formation. Practical blasting methods in presplitting such as propellant presplitting and precision presplitting would not be applicable based on the shockwave theory yet are widely used and documented in the industry. Along with this, modern research using a borehole simulation device and advanced pressure gauges have allowed the authors to obtain true borehole pressures in decoupled blastholes. This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

By Anthony Konya, Calvin J. Konya

This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

Feb 1, 2020

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By Jianping Li, Ernesto Villaescusa, Kelly Fleetwood

During blasting, stress waves propagate through a rock mass, inducing stress and strain changes. This applied deformation affects intact rock, existing discontinuities, mine excavations, and engineered structures in the proximity of the blast. Traditionally in blasting, stress waves are quantified in terms of peak particle velocity (PPV) or peak particle acceleration (PPA), based on the method of measurement and the specified allowable tolerances. During analysis, the peak particle motion is coupled with an explosive source through various scaling laws to develop rock-specific attenuation relationships. Some studies have expanded this practice to the development of damage threshold values based on measured or predicted peak particle velocities. PPV-related thresholds are generally based on empirical models, where observation of overbreak, cracking, or fall-off are used to quantify damage. This method is often paired with the application of elastic plane wave equations to calculate the blast induced strain or the PPV threshold for tensile rock failure. Other factors that must be viewed critically in such models are the methods used to collect and analyse blast vibration data and the application of inappropriate vibration attenuation relationships.

Jan 1, 2009

By Sami Kara, Marsel Nabium

This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution

Feb 1, 2020

By Jacqueline Berendzen

Summer internships are a great way for students to explore different career paths in the industry and get first hand experiences with potential employers. As a junior in mining and explosive engineering, my 2009 summer internship gave me a behind the scenes view of the actual workings of an explosive company and the role they play in the mining industry.

Jan 1, 2010

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By Thomas Pallua, William C. Gates

"Two major railroad companies have identified several segments along the railroad corridor betweenTehachapi and Bakersfield, Kern County in California that require construction of a second track to improve operations in this area. The total project proposes an upgrade of five segments along the Tehachapi-Bakersfield route. The authors focused on two segments: Walong to Marcel and Cliff Siding Extension. The second track project comprised design of a through-cut adjacent to an existing tunnel and up to 120-feet-high (36m) side-hill cuts (both in granitic rock). The authors characterized the geologic ground conditions and ground behavior, including rock mass quality and strength using a combination of rock core drilling and rock slope mapping. The rock mass is generally characterized as granitic tonalite with strong core stones surrounded by a matrix of decomposed granite (DG)."

Jan 1, 2017