Search Documents

By Dale Preece, Stephen Chung, Richard Jensen

DMCBLAST_3D is a three-dimensional extension of the proven two-dimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2001

The use of angled shot holes can be extremely effective in blasting faces that either have a great deal of toe burden or where it is difficult to give a drill access to a face due to backbreak and face erosion. However many quarry operators are wary of using angled holes because of the perceived possibility of increased flyrock and uncertainty of the driller's abilities to drill at the designed angle.

Jan 1, 1994

By J S. Kuszmaul

The economic development of modified in situ oil shale retorting will benefit from the ability to design a blasting scheme that creates a rubble bed of uniform permeability. Preparing such a design depends upon successfully predicting how a given explosive will break rock. Numerical models are used to make predictions of the extent of damage caused by an explosion.

Jan 1, 1985

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Lyall Workman, Jack Eloranta

In this paper results of drill to mill research are examined. It is found that several descriptors of blasting results change when the powder factor is increased. Fragmentation shifts toward a finer distribution. The Bond work index decreases and the product of the t10 model breakage parameters increases. Both of these indicate more softening of fragments. There is research that found large differences in bond work index and other studies that find a much smaller decrease. Even at the lower decrease, however, some savings in energy cost can accrue in hard ores ground to small size.

Jan 1, 2009

By Mark S. Stagg, Steven V. Crum

The Bureau of Mines is conducting research to develop methods to control fragmentation and improve productivity in surface mine blasting. As part of this research, PRONT02D, a two-dimensional finite element computer program developed at Sandia National Laboratories, was employed to model the fragmentation produced from RS-50, a single hole, reduced scale bench blast in a massive dolomite. The fragment size distribution obtained from the computer simulation was calculated using a submodel that utilizes the crack density and nominal flaw size values computed by PRONT02D.

Jan 1, 1989

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

This paper examines the hypothesis that the fragment size distribution of blasted rock contains information about the changes in fragment sizes with distance from the borehole, and that this information can be interpreted and used to predict the effect of powder factor on fragmentation. A set of simple relationships between the fragment size distribution curve and the dependence of fragmentation on powder factor is proposed. The equations derived are compared with published data on fragmentation in small scale blasting. Two data sets were analyzed, and the results confirm the hypothesis.

Jan 1, 1997

By Robert B. Hopler

This paper reviews, from the historical standpoint, the development of the commonly-used terms such as "No. 6 and No. 8" with regard to detonator strengths. The origin of the strength terminology is reviewed, and the many methods developed to compare the strength of one detonator to another are described, with the good and bad points of each method outlined. The "miniature cartridge test," very highly regarded by both the U.S. Bureau of Mines and Institute of Makers of Explosives in the 1930's and early 1940's, is described in detail, as is a test developed and used by IRECO.

Jan 1, 1992

By G Alan Foster

The presence of approximately 600,000 attorneys in the U.S.A. and the determination by the courts that blasting is considered an 'ultra hazardous' activity makes every practical blaster aware that at some time during his working life he will probably be faced with defending himself in court.

Jan 1, 1982

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

This paper describes experience in designing and implementing casting blasts over the past fifteen years. Important design parameters such as powder factor, burden and spacing, blast pattern geometry, front row burden and toe distance, pit width versus height, blast length, explosive selection, millisecond delay timing and tie-in types are discussed.

Jan 1, 1995

By Terry Graf, Bill Thompson, John Guenther

SYNCRUDE CANADA LTD.. operates the largest synthetic crude oil production facility in the world. Over 60,000,000 Bank Cubic Metres of oil sand is mined each year from their open pit located in Fort McMurray, Alberta. Despite the extremely cold temperatures encountered during the winter months and the problems associated with frost buildup, SYNCRUDE has continued to operate on a 12 month per year basis. In 1989 SYNCRUDE mine management embarked on a comprehensive Frost Blasting program to improve mine production of their oil sand moving equipment. The following paper will discuss the development of their frost blasting program to its current status.

Jan 1, 1993

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By J R. "Dick" Daniel

In the fall of 1988, The Cannon mine decided to investigate a central blasting system based on conventional electric blasting detonators being used to initiate rounds primed with Nonel detonators. The advantages of this hybrid detonator system were viewed as being safety and cost effectiveness. A study was done reviewing the safety aspects of utilizing a permanent blasting line installed throughout the main haulage drifts to a central blasting station located at the mine portal. The study addressed the following potential safety hazards: radio frequency induced current, stray current from both electrical utilities and transmission lines, galvanic and electrostatic sources of extraneous current.

Jan 1, 1989

By Raymond V. Adolphson

Use of explosives effectively and safely has come a long way since its discovery and early stages of development. The need to objectively and functionally train personnel in the safe and effective use of explosives became forcefully apparent in the early 1930's in Forest Service work at the start of the Civilian Conservation corps program.

Jan 1, 1978

By Sushil Bhandari

Presented here is the simplified process of fragmentation of homogeneous rocks by blasting based on experimental studies. Small scale single hole blasting experiments on jointed limestone are described. Results show that directions of joints overshadow the degree of fragmentation and also influence the remaining rock. The possible influence of joints on the process of fragmentation of non-homogeneous rock by blasting is also discussed.

Jan 1, 1983

By M Lemieux, R Mason

The SABREX blast modeling program was introduced to I.O.C.C.'s Carol Lake Iron Ore Project in December 1987. As part of CIL's Technical Services, SABREX was used to implement an optimization program designed to analyze and introduce various grades of MAGNAFRAC at a constant pattern while maintaining acceptable blast results.

Jan 1, 1989

By Charles E. Joachim, Christo V. Lunderman, Charles R. Wdch

The U.S. Army Engineer Waterways Experiment Station (WES) recently conducted a series of precision-scale water shock experiments which consisted of the detonation of several 8-gram, 10-gram, and 12-gram spherical explosive charges. The charges were fabricated from NAX 2000 Primasheet explosive and were center-detonated. Commercial tourmaline crystal water shock sensors were used to measure the induced pressure fields in the water. The measured water shock waveforms and related parameters from the precision-scale experiments were in general agreement with data from larger-scale experiments.

Jan 1, 1998