Search Documents

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Benjamin Cebrian

Metallurgical testing at Cobre Las Cruces prior to production at the mill was done with overburden gossan. Some of that test gossan was a very fine material, wet by the water conditions at the bottom of the pit. When processed and stored wet at the fines material 3000 tonne (3307 tons) silo, this material cemented in a very unusual manner.

Jan 1, 2010

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By R W. Givens

Comparison tests were performed on 6 emulsion concentrates, 3 microballoon sensitized emulsion concentrates, and 2 water gel concentrates from 8 different sources with ANFO used as a control standard. Variables measured include density, detonation, velocity, detonation pressure, calculated borehole pressure, viscosity, and lead cylinder deformation for blends of 15%, 30%, and 45% concentrate and AN/ANFO blends. Comparative results are presented for detonation velocity vs. deformation, and percentage of inherent air vs. deformation for these blends. It was hoped that these tests would serve as a tool to facilitate the comparison of different manufacturer's concentrates in AN/ANFO blends for equivalent performance characteristics and to help evaluate these products on an equal basis for bid solicitation purposes.

Jan 1, 1990

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Savas Gorgun

The principal disturbances created by blasting in open pit mines are vibrations, air blast and fly rock. All of them, under some circumstances, caused damage to structures nearby and apart from this can be the source of permanent conflict with the inhabitations who live close to the operation. Therefore, prediction of ground vibration components is of great importance for the minimisation of the environmental complaints. This paper presents the result of ground vibration measurements induced by bench blasting realised at Can Open Pit Coal Mine located close to the residential area of Can town. Within the scope of this study, in order to predict peak particle velocity and determine the slope of the attenuation curve for this site, ground vibration components were measured for blast events during bench blast optimisation studies over a long period. During the study, while the parameters of scaled distance were recorded carefully, the ground vibration components were measured by means of two different types vibration monitors (White Mini-Seis and Instantel Minimate Plus Model) for 54 blast events. At the end of evaluation an empirical relationship with reasonable correlation was established between peak particle velocity and scaled distance for this site.

Jan 1, 2001

By Andrew F. McKown

This paper will discuss the mechanisms of potential damage from close-in construction blasting, concentrating on two mechanisms: elastic ground vibrations and non-elastic (permanent) ground deformations. The latter will be shown to be the most dangerous for close-in blasting. With respect to elastic ground vibrations, discussion will center on the differences in vibration frequencies and impacts between typical close-in construction blasting and typical mine and quarry blasts, and how using vibration criteria derived for residential structures near mines can lead to very conservative criteria for close-in construction blasting. The effects of high frequency vibrations seen in close-in blasting will be commented on. Factors affecting the magnitude of ground motions will be discussed. Simple, practical techniques will be presented to minimize the potential for damage from close-in blasting, by minimizing the potential for rock block movement or ground heave. Case histories will be presented to illustrate some of the techniques discussed, and give examples of successful close-in blasting projects.

Jan 1, 1991

By Catherine T. Aimone-Martin, Elena Oana Jacobs, Brent Meins

Accurate pressure measurements during underwater detonations are critical for the protection of structures and mitigating impacts to fish and marine mammals. Current guidelines that limit underwater pressures are based on past studies, many of which used sample rates of 48 and 65 kS/s (48,000 and 65,000 samples per second). These sample rates may be insufficient to accurately record high frequency, sharp rise time blast pressures. As such, pressure thresholds associated with fish and marine mammal injury or mortality may be underestimated, calling into question the pressure and sound pressure level guidelines that govern underwater blasting today.

Jan 1, 2019

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Tyler Rockley, Greg Bailey

This paper is an engineering case study of a blast performed on a highly weathered sandstone isthmus in an area sensitive to vibration and airblast, the challenges associated with such a blast, the methods used to understand rock characteristics, the blast design considerations and a discussion of the blast results. The purpose of the blast was to remove approximately 12 feet (3.7 m) of surface material in order to install a pumping station. The isthmus provided several challenges due to the weathering of the rock and multiple open faces with surrounding water. The highly fractured and weathered rock was subject to about ten years of freeze thaw cycles, influx of water and seasonal submersion. As such, all actual rock conditions were indefinite, including fracturing, rock properties, degradation and competency. The isthmus also had immediate neighbors who were unused to the environmental effects of blasting. To help continue to keep the social license to operate in the area, it was important to reduce the ground vibration, blast duration, dust and airblast. These factors required a better understanding of how the rock would respond to blasting. In order to do this, test blasts were performed on the same geologic formation in a different location of the quarry that was less sensitive to vibration and airblast effects, allowing the blast parameters and design to be verified and refined. The test blasts were performed while monitoring vibration, air blast, material movement and overall shot performance, and the blasting parameters were adjusted accordingly. The isthmus blast was performed based on the final design from these test blasts. The drilling and loading of the shot all met acceptable criteria and were comparable to the test blasts. The blast performance, however, was not as expected; the depth impacted by the blast was substantially more than expected. Since the test blasts were performed in the same formation, but in material that was significantly less weathered than the isthmus, the actual effect of this weathering was the only difference between test blasting and the isthmus blast. Thus, these results can be used for future reference to highlight the effects of blasting such highly weathered rock and help instruct the blast design in similarly complex conditions.

By Finn Ouchterlony

"Recently detailed fragmentation data from blasts fired with electronic delay detonators (EDDs) in the Red Dog mine in Alaska were presented. They include a comparison with pyrotechnic detonators fordifferent in-­-row delays in a standard pattern and EDDs in an expanded pattern. Fragmentation was measured on the belt after the primary crusher. The Rosin-­-Rammler function (RR, two parameters) was used to describe the crusher product. This was combined with the JK SimMet crusher model and the CZM blast model (Crushed Zone Model, three to five parameters) to estimate a reasonable crusher feed (muck pile fragmentation or run of mine, ROM) for each fitted product. In this way the effect of delay timing and electronic detonators on the median fragment size x50 and uniformity coefficient n for both crusher product and the blasted rock was determined. "

Jan 1, 2012

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Pavel A. Torres, Darwin Torres, Sandro Huaman

Given the limited efficiency of blast-induced ground vibrations prediction empirical models, due to the complex geological system from a Peruvian mine. An artificial neural network was built in order to get better results. More accurate and precise predictions allowed the generation of blasting domains for future designs and decision making.

Feb 1, 2020

By Owen Collins

In surface mining, designing patterns to reduce the probability of flyrock and optimizing fragmentation through powder factor calculations are important for safe, efficient blasts. The designed powder factor is established for the blast once parameters such as burden, spacing, stemming, and powder column height are determined. In practice, these parameters are usually constant throughout a production blast with row-to-row burden and spacing. However, challenges can arise with the introduction of an open face. Many variables could necessitate the adjustment of the face row to optimize blast results. Variables include drill accessibility, challenges with toes, overhangs, and geology. The approach is often, but not exclusively, determining how to keep a consistent powder factor from the open face through the body of the blast. However, the solutions used vary case-by-case and rarely are two blasts the same. Technology has improved the ability to deal with challenging face conditions. 3D modeling with the aid of drones allows the application of angled holes to be more effective and simpler. This is just one instance where technology has improved blast results. This paper will present solutions to challenging face conditions. Thoroughly analyzing instances where challenging open-face variables were met with an effective blast solution could help provide insight as to what yields consistent blast results.

Jan 26, 2026

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

By Michael A. Peltier, Dennis V. D'Andreal, Larry R. Fletcher

Accident data obtained from the Mine Safety and Health Administration (MSHA) were analyzed by the Bureau of Mines to determine the most frequent causes of blasting accidents in U.S. mining and to examine trends in blasting accidents. This accident analysis is an update of a similar blasting accident study conducted by the Bureau and published in 1983. The analysis shows that there has been a recent reduction in mine blasting accidents: The annual average number of nonfatal injuries has decreased from 107 for 1978-81 to 46 for 1982-85. The annual average number of fatal injuries was reduced from 11.3 to 5.0 during that time.

Jan 1, 1987