Search Documents

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By Markus Pötsch, Andreas Gaich

Optimization of surface blasting based on 3D models from drone imagery and a closed loop that starts with an automatic analysis of the geometry and the geological conditions and ends with an objective assessment of the blast result.

Feb 1, 2020

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Edward J. Walter

Our modern technology is provided with a unique but flexible power tool in the use of explosives. A by-product of explosives usage is vibration or elastic deformation of the earth which is annoying to the ordinary person and can be damaging to structures. The problem is not new, it is more than fifty years old. Adequate vibration standards have been developed so that blasting programs can be properly planned and safely executed. Changes in our social culture have somewhat changed the emphasis in blasting vibration from damage considerations to the much lower level of citizen annoyance. Vibration codes based on this level will be highly restrictive and prohibitively costly. Cooperation is urged between operators, community officials, agencies at all levels,and consultants to see to the development of sound realistic vibration codes.

Jan 1, 1975

By Visitor Makiyi, Chris Batten

Poor coal recovery due to coal damage or loss caused by blasting can have a significant impact on a mining operation. Increasing coal recovery by reducing blast damage can provide a significant opportunity for coal mines to maximise their revenue and reduce their operating costs. This paper provides details on advanced drilling and blasting techniques used throughout the coal industry globally to prevent coal damage and movement during blasting. Typical coal loss and damage mechanisms are explained, along with how each of the applied techniques works to minimise the impact of each mechanism. Key requirements for a coal loss reduction program are detailed with typical design parameters used for each of the methods discussed. The positives and negatives of each method are also provided to enable comparisons and help determine suitability for a particular coal mining operation.

Jan 21, 2025

By R. Sibley, K. Perry, E. McCorkle, M. Coy

Black powder has been used in fireworks since the 10 th century in China. To this day, black powder still has a variety of uses, including fireworks, and remains relatively unchanged. Black powder is used in the firework shell to help produce the effect and in the lift charge to propel the shell skyward. The performance of fireworks shells used in displays varies greatly. In fireworks shells, there are two different black powder charges that differ in construction based on the desired performance of the shell. The two charges consist of the lift charge and the break charge. The lift charge is the first to fire and propels the shell out of the mortar. The break charge is the second to fire and is initiated after a delay from the lift charge; its purpose is to burst the shells effect over the desired area of the sky. The lift charge provides the shell with its initial velocity by pressurizing the mortar below the shell body. The pressurization process is violent and occurs in fractions of a second. The purpose of these experiments are to better understand the pressures sustained in fireworks mortars during the firing process. Mortars and shells vary by size and weight. Pressures in each mortar were monitored at various heights along the mortar to provide a pressure profile during shell lift. A high-speed camera was used to measure shell exit velocity near the mortar’s muzzle. This information was correlated with the size and weight of shells and their respective lift charges

Jan 1, 2024

By R Ludeling, Klaus G. Hinzen, Ulrich Steiner, Friedrich Heinemeyer, Peter Roh

A method for hybrid modelling of blast vibrations in time domain is developed. Field seismograms of single shot experiments are combined with computer simulations. In this way firing times of blastholes in a pattern can be optimized due to diverse criteria like maximum velocity amplitude and frequency content of the vibrations.

Jan 1, 1987

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By Peter Bellairs, Anthony Bubb

The Porgera Gold Mine is located at an altitude of 3000m in the central highlands of Papua New Guinea some 600 km Northwest of Port Moresby the capital city. Access to the mine is via a five hour trip on an unsealed road from Mount Hagen the nearest regional centre or 40 minutes via air. The mine operates on a fly in - fly out basis and currently produces ore from both opencut and underground operations with the former providing the bulk of the mill feed. Opencut mining utilises conventional truck / shovel, drill and blast methods on both 10 metre and 14 metre bench heights with the larger benches being restricted to the stripping areas. This paper presents the strategy used and the results of a blast optimisation process in the opencut that was a joint effort between the mine personnel and the explosives manufacturer/supplier.

Jan 1, 1997

By H Leonard Mangum, Victor C. Bryan, Dan McCutchen

Recently there has been an unprecedented marketing effort to promote the advantages of various non-electric initiation systems. This activity has probably been influenced by a major manufacturer's decision to discontinue electric detonator production. Subsequently, distributors of explosive materials, rather than introducing new electric detonator brands, are emphasizing the use of existing non-electric systems. In many cases, such methods fill the need of explosive users in the quarry industry. However, the use of any initiation system should be based on performance, rather than the bent of the market or convenience to the supplier. This analysis is an evaluation of the performance of non-electric systems with emphasis on double trunk line and loop (redundant), as compared to precise electric detonators in use by Martin Marietta. Redundant non-electric detonators, even though more costly, offer the most reliable method of non-electric initiation. However, state-of-the-art precise electric detonators give the best overall performance, except in an environment involving extraneous electricity.

Jan 1, 1990

By Carlos Neto

Traceability is the capacity to recover background, application or localization of an item, through a single, standard and registered identification. It is the identification process necessary to follow all events, occurrences, handlings and movements of a product. Generally speaking, companies and governments in the world are seeking ways for tracing the distribution of controlled products, such as food, medicines, firearms and explosives, within the supply chain as to increase safety of its consumers and the environment (ISO 14000).

Jan 1, 2007

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed. Based on an ellipsoidal shock shape approach, the proposed model uses the quasi-one dimensional theory for the axial flow solution and combine the post-shock sonic flow criteria with some limiting conditions for the explosives’ unconfined radius determination. Due to its attractive fitting capability for unconfined detonation experimental data, the model offers the possibility to predict the non-ideal detonation state for any diameter, resulting in a full mapping of the diameter-effect curve of the explosive. Thus, the proposed engineering approach is used to model the main properties of some of the most common ammonium nitrate-based explosives used in mining and quarrying industries, including the complete axial flow solution.

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks

Feb 1, 2020

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By Paulo Couceiro

Highly non-ideal explosives usually tend to react expressively below their ideal detonation velocities. In these cases, dimensional effects and product heterogeneities become important to proper model the detonation state. Although Direct Numerical Simulation (DNS) techniques can provide a complete and exact solution for this problem, its actual computation cost is still not practical for industrial applications. In order to minimize these constrains, a simplified two-dimensional steady non-ideal detonation model for cylindrical stick explosives is developed.

Feb 1, 2020