Search Documents

By Teemu Väyrynen, Matti Vilkko, Antti Jaatinen, Pekka Itävuo

"This paper shows that smooth and accurate feed-hopper level control is essential for consistent cone crusher operation. The objective of the paper is to define the best practices for tight control of cone crusher feed-hopper level. The paper discusses the challenges involved in a delay-dominant level control problem (specifically, dead-time-induced performance and stability issues, mass flow disturbances, process and actuator non-linearity) and proposes five corresponding control structures. The performance of the proposed control structure candidates is evaluated in a simulation study and, finally, a full-scale experiment is conducted for the best-performing candidate. The results of this study emphasize the importance of control structure selection. While the most obvious control structures failed to deliver the desired performance, the best result was achieved by using control structures that eliminate the conveyor transport delay (dead-time) from the control loop. In practice, the control loop dead-time can be eliminated by either using an actuator (variable-speed feed conveyor) that is connected directly to the feed-hopper, or by redefining the process boundaries closer to the used actuator (regulate the circuit mass balance instead of feed-hopper level). The presented control structures provide means to achieve a consistent cone crusher performance and size reduction. This facilitates efforts to improve the plant’s performance and increases the plant’s overall stability."

Jan 1, 2014

By R. V. Kononko, A. Yu. Chikin, R. N. Rakhmeev, Yu. O. Fedorov

"The focus of the study is finding a solution that can help to improve diamond recovery in diamond-bearing gravity concentrates upgrading flowsheets. The purpose of the study was to develop and prove scientifically a separation method of diamonds recovery from gravity concentrates regardless of their fluorescence ability induced by X-ray radiation. Two promising recovery methods applicable to diamonds of this type are proposed, i.e. an X-ray radiometric method based on an instantaneous analysis of a secondary X-ray spectrum of separated particles, and a triboelectric method that relies on noncontact measurements of particle charges obtained during its motion in a vibratory tray. As a part of the laboratory study, X-ray fluorescence spectra of the collection of diamond crystals and main associated minerals and rocks at a particle size of -6+3 mm were produced. The analysis of the produced secondary X-ray spectra showed a significant difference between crystals, minerals and rocks within the analytical area of Ca, Fe and Zr due to the absence of calcium, iron and zircon elements in diamonds. Additionally, the scattered X-radiation level of diamonds substantially increased under the influence of X-ray radiation. Such a difference is a physical base of a new method of diamonds recovery from mineral mixtures. The laboratory study on triboelectric characteristics showed that a significant portion of diamonds gained an electric charge of a magnitude that was much higher, compared to associated minerals and rocks. The laboratory and industrial tests and the separation indicators demonstrated a high efficiency. A proposed X-ray radiometric method provides recovery of all types of diamonds regardless of X-ray fluorescence levels, with high selectivity and recovery rate of at least 98%. This proposed separation method is protected by a patent of Russian Federation (No. 2551486, “A method of X-ray radiometric separation of diamond-bearing materials”). Triboelectric separation organized in two stages (main and control) ensures recovery of up to 98-100% of diamonds at a particle size -5+2 and -2+1 mm,. More than 10 triboelectric separators successfully operate in active diamond processing plants in the Russian Federation."

Jan 1, 2018

By Liu Xiaodong, Jiang Meifen, Kou Xiaoyan, Lu Xianjun

"Two low grade calcium bentonite (Ca-bentonite) from Hejia (HJ) and Boteng (BT), Shandong, China, mainly contain montmorillonite and quartz, and slightly feldspar, calcite, and montmorillonite content are 32.37% and 55.90%, respectively. In order to examine the feasibility to produce activated clay to meet the standard of Chinese chemical industry (HG/T2569-2007), three types of industrial production process are proposed according to the screen test. The first process is grinding the raw bentonite to -200 mesh and then activating. The second is to activate the raw bentonite directly, and then classify the production to -200 mesh. The last one is to activate the raw bentonite after purification. Three parameters, which are sulphuric acid strength, ratio of liquid to solid and treatment time, are optimized via orthogonal test for every process. The preliminary test indicates that it is feasible to produce acid bentonite of difference quality. For the sample of HJ, milling the raw to -200 mesh first and activating afterwards, the parameter is at 9% acid strength, the ratio of liquid to solid 2, the time 4 hours, temperature 90°C, the products can meet the qualified grade for animal and vegetable oils refining. For the sample of BT, milling the raw to -200 mesh first and activating afterwards, the parameter is at 15% acid strength, the ratio of liquid to solid 2.5, the time 2 hours, temperature 90°C, the products can meet the qualified grade of high decolorization for petroleum products refining. For the sample of BT, adopting purification to -325 mesh by stirring and rubbing at first, and then activating at 9% acidity, under the conditions that the ratio of liquid to solid is 2, the time is 2 hours and the temperature is 90°C, the products can meet the first grade of high activation degree for petroleum products refining."

Jan 1, 2014

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012

By V. M. Mankov, O. V. Zamyatin

"Fine free gold at a size of minus 250-100 µm can be effectively recovered from mineral materials (buried clay placers, saprolites, gold-bearing aggregates, technogenic sands etc.), or MM, using some developed and implemented in practice cost-effective basic technological schemes of MM processing at every stage: exploration, main concentration processes, upgrading of gravity concentrates etc. Such technologies are based on mineral materials composition, different content of fine gold mass fractions, and include improved two-stage sluicing technology, jigging technology, advanced technology and integrated technology. The main operation principle of the given technologies is gravity concentration. They provide recovery of fine gold of any size from MM, including gold finer than 100 µm, using concentration systems and plants with a capacity of 1-2 and up to 100-200 m3 per hour. Selection of a cost-effective technology depends on its technical and economic viability regarding to mineral material composition, optimum performance and concentration rate. The developed technologies of mineral materials concentration establish a balance between technological, technical and economic factors, and ensure profitable development of deposits containing free gold and characterized by a complex composition of concentrating material. Free gold recovery with these systems increases by 2.0-2.5 times for gold particles at a size of minus 250+100 µm and 10-30 times for gold particles of minus 100 µm, compared to conventional sluicing systems. The Irgiredmet Institute has developed and supplies primary concentrate washing machines for upgrading gravity concentrates of up to 100 mm in size, with a capacity of 1.0-5.0 m3/h, fitted with various production equipment including pyro- and hydrometallurgical systems. Additionally, the Irgiredmet Institute develops and manufactures systems of mechanized processing of geological and technological samples (UOMP; registered design certificate No.27505, Russia) designed for complete recovery of free gold in the process of geological samples handling and decreasing of a human factor influence. A system includes a package of technologically associated disintegration, classification and concentration equipment with some “know-how” elements that provide effective recovery of fine gold at the exploration stage. A number of Irgiredmet’s patented technologies and systems (patents of the Russian Federation) have no equivalents in the field of mineral processing and provide designing of technologically practical and cost-effective flowsheets that offer higher recovery of gold of different sizes (fine gold), at every stage of processing of mineral materials including basic concentration processes, upgrading and exploration etc."

Jan 1, 2018

By Dave Deglon

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The WCMPF was established in 1989 with the aim of improving mineral processing education in the Western Cape. Since its inception the WCMPF has had a number of successes in this area, especially in improving the quality of mineral processing practical training. In addition, the WCMPF has played an important role in promoting liaison and interaction between tertiary educational institutions teaching mineral processing in the Western Cape. Over the past decade the WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. This paper presents an overview of the activities of the WCMPF and attempts to encapsulate the ‘lessons learned’ from over a decade of successful functioning as a collaborative educational initiative in mineral processing.

Jan 1, 2003

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By S. Safak

Europe retains a modest position in world mining activity in terms of scale of production and mineral reserves but maintains a non-negligible role in the world mining industry. The concept of sustainable development resting on three pillars of economics, environment and social development has become an increasingly important factor in the European mining sector and a major influence on the related policies of the European Commission. Members of European mining industry shall conduct their activities according to the principles which promote sustainable development. A successful minerals planning policy should create the legal administrative environment that is necessary to ensure the sustainable supply of minerals to society within the framework of sustainable development. Members of the European mining industry shall conduct their activities according to principles which promote sustainable development. The challenge for sustainability is to find a balance between securing minerals supply, protecting the environment and achieving social progress. The point of balance depends on the range of policies adopted by governments. In this paper the development of the sustainability of the mining sector in EU and the social component of sustainability in the mineral industry is discussed.

Jan 1, 2014

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By A. Güney

Currently, recycling technologies use relatively homogeneous plastics because hand-sorting waste feed is too expensive. Many promising technologies for separating mixed thermoplastics are being investigated, but they are still uneconomical and unreliable. Burning plastics for recycling is not used because of poisonous gases released when their burning. PET and PVC cannot be separated using conventional gravity separation techniques because their specific gravities overlap; PET density changes from 1.33 g/cc to 1.37 g/cc and PVC density is between 1.32 g/cc and 1.37 g/cc. For this reason, plastic recycling needs new techniques. Among these techniques froth flotation, also used in mineral processing, can be useful for its cost and simplicity. In this method, a plastic is selected from mixture, tried to regain its natural property, hydrophobicity. In this study the experiments were applied by using plasticizer reagents to make the selected plastics hydrophobic and us-ing NaOH to render the other hydrophilic. Post-consumed PET and PVC are evaluated by concerning the effects of selected parameters (particle size, concentration of plasticizer reagent, amount of NaOH, conditioning time and the effect of conditioning temperature). At the end of the experiments, optimum parameters for selective flotation of PET from PVC was found as particle size of -4.76 + 3.36 mm, NaOH amount of 30 kg/t, conditioning temperature of 75°C, conditioning time of 30 minutes, reagent amount of 300 mg/L. Consequently, PET was re-covered with 99.7% purity and 57% efficiency.

Jan 1, 2014

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

In view of the shortage of soft water all over the Middle East countries, seawater may be used to replace the fresh water in flotation beneficiation. The flotation process required about 7 m3 of fresh water/ ton ore. This article aimed to study the effect of seawater cations and anions on the flotation process of four important mineral commodities. The adsorption of collector, zeta-potential, zero point of charge and floatability of pure minerals were studied. The individual effects of different cations and anions that are predominant in seawater, within their more or less actual concentrations were studied on individual mineral and on groups of them. The troublesome Ca2+ and Mg2+ ions, in the anionic circuit could be controlled by soda ash addition to the pulp before the anionic collector. The addition of sodium silicate improved the floatation selectivity of mineral mixtures and natural ore. At the optimum conditions the calcareous phosphate ore yielded a concentrate recovery of 83% with a grade of 34% P2O5, with 0.61%MgO, which from an ore assaying (25.3% P2O5 and 9.4% MgO).

Jan 1, 2003

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018