Search Documents

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even where possible, equilibrium data with a suitable Henry.s law constant are seldom available.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, KGa values can be calculated for the pilot plant and then scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance."

Jan 1, 2003

By J. X. Zhang, F. S. Niu

"In order to accurately detect whether the collision occurs between particle and bubble in flotation process, a collision detection method of particle and bubble, which based on morphological image processing and Otsu method, is presented. First of all, it utilizes image pre-processing to optimize images, the target area and the background area are segmented by Otsu method. Then, particle and bubble are fitted to a circle combined with the least-square method. It’s convenient to obtain the coordinate information and radius. Finally, the position of all particles is extracted to an image, which achieves the particle tracking and avoids the complexity of the continuous frame image tracking.Experimental analysis shows that the relationship between the two ordinate difference d and the bubble radius r has a certain influence on the collision detection when the dripping particles are close to the bubble, when d>r, the detection accuracy is 92%;When d=1/2r, the detection accuracy is 97%;When d=0, the detection accuracy is 100%. The result indicates that this algorithm can detect the collision between particle and bubble quickly, and the working hours of manual test are saved effectively ,the best position of dripping particles close to the bubble which is taken with a CCD camera should be in the range of the particle and bubble’s ordinate difference less than half of the bubble radius.INTRODUCTIONFlotation is an important technical means to separate useful minerals from ores. The flotation process of ores and materials in the world is treated by flotation technology up to billions of tons every year, so the study of flotation process is particularly important. Raising the collision probability between mineral particles and bubbles in flotation process is one of the key factors to improve flotation separation efficiency[1]. The study indicates that[2-4] the collision probability between particles and bubbles is influenced by many factors, such as particle density, particle size bubble size, etc. The analysis of these influential factors requires a lot of experiments. Therefore, it is of great significance to design an accurate collision detection method for the research of this field."

Jan 1, 2018

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By K. Sasaki, H. Miki, Y. Muta, T. Hirajima, G. P. W. Suyantara

"Selective flotation of chalcopyrite and molybdenite is continuing problem since its selectivity is not perfect and current NaHS process needs closed system flotation plant because of hydrogen sulfide emission on acidic condition. Some alternative additives investigated as chalcopyrite became hydrophilic and molybdenite kept hydrophobic. XPS analysis indicated chalcopyrite became hydrophilic since iron and copper sulphate, hydroxide was covered on the surface whereas molybdenite kept hydrophobic since only molybdenite can be seen. Flotation experiments of chalcopyrite and molybdenite mixture sample indicated excellent separation that 95% of molybdenite can be recovered as froth and 93% of chalcopyrite can be recovered as sink. Flotation experiments with real bulk flotation concentration indicated similar separation result compared with current NaHS additive system. Possible mechanisms and detailed phenomenon were investigated based on the surface analysis and thermodynamic calculation etc. this alternative additive is easy to handle compared with NaHS since it does not emit effluent gas and commercially preferable.INTRODUCTIONMany copper mine often associates molybdenite (MoS2) as trace mineral. It is important to separate molybdenite and copper mineral efficiently since molybdenite is valuable mineral and also contamination of molybdenite into copper concentrate decrease concentrate value. Conventional separation of copper sulfide and molybdenite has been achieved with sulfide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulfide (Bulatovic, 2010; Ansari and Pawlik, 2007b). However, this current process shows imperfect molybdenite recovery (Liu et al., 2012, Zanin et al., 2009) and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant (Ansari and Pawlik, 2007a). there are still unknown on the effect of depressant NaHS, but one of the theory is NaHS reductant effect. It is worth to investigate the effect of other reductant as depressant on chalcopyrite. On this research, typical reductant, Na2SO3 are added to utilize for selective flotation of chalcopyrite and molybdenite."

Jan 1, 2018

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By S. Kelebek, A. Khan, J. Caceres, D. Beckett

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance (Figure 1). The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents (Figure 2)."

Jan 1, 2003

By Vincent C. Smith, Agit Singh, Daniel de V. van der Spuy, Bernard Muller

"Process control in the minerals industry is made difficult by factors such as the multivariable nature of the processes, noise, many disturbances, the changing nature of the processes, nonlinearities, process constraints, slow responses and large deadtimes. A good example of such a process is a milling circuit, where all these problems are experienced. Since model predictive control (MPC) effectively handles most of these difficulties, Mintek decided to develop, customise and test an MPC controller for milling control.Conventional MPC uses a dynamic model of the plant to calculate the future (predicted) plant outputs based on the movements of the manipulated variables in the past. The future moves of the manipulated variables can then be calculated using an optimisation algorithm that will minimise the difference between the setpoints and the predicted outputs. The least squares optimisation method is the quickest, but it does not cater for process constraints. Constraints can, however, be handled explicitly by using a quadratic programming optimisation method. This method ensures that the variables stay within the constraints at all times, but the calculation procedure is much more computationally intensive.• modifying MPC for the Minerals Processing IndustryIt was found that in order to obtain good, robust control using MPC in the minerals processing industry, the conventional MPC algorithm had to be adapted. The MPC controller was first tested on an extensive milling simulator, which was specifically developed for that purpose. Problem areas were identified and the MPC controller was specially adapted to accommodate for these difficulties. Some of the adaptations to the conventional MPC algorithm and special features added were as follows:Since milling plants contain many integrating processes (e.g. sumps), and integrating errors can cause offsets and poor control, it was essential that integrators be handled explicitly. This problem was solved by adapting the algorithm and also using an integrating error portion to compensate for integrating errors.Constraints on the inputs and outputs adversely affected the control. The controller using simple least squares optimisation was tuned with the constraints in place, while the maximum expected setpoint changes were made. This ensured that the process would be able to handle most setpoint changes up to these expected values without violating the constraints. A later improvement on this method was the incorporation of a quadratic programming algorithm to perform the optimisation. This method handles limits explicitly and was shown to perform better than the least squares methods (at the expense of a much higher computational cost)"

Jan 1, 2003

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

"The effect of operational conditions, such as air flow rate, impeller speed and solid concentration, as well as the effect of solids concentration and frother dosage, on the bubble size distribution produced in a lab scale flotation cell, were investigated. The cell was operated under batch conditions. The measurement of bubble size was accomplished using an automated photographic technique. The technique enabled fine and coarse bubble distributions to be measured in two-phase (liquid-gas) and three-phase systems (solid-liquid-gas). In each experiment, around ten thousand bubbles were characterized.This paper discusses the main results obtained using the new photographic technique and compares these with previous findings available in the literature. The results indicate that photographic techniques combined with digital imaging processing might become a standard technique for measuring bubble size distribution in flotation machines.HUT BUBBLE SIZE ANALYSERThe importance of having precise and reliable equipment for measuring bubble size distribution in industrial flotation machines has been widely recognized. The measurement of bubble size, particularly in three-phase systems, is rather complex due to the opaque nature of the pulp. However photographic techniques combined with ingenious sampling techniques are utilized for overcoming this difficulty. The technique named HUT, combines previously developed visualization methods with digital image processing procedures. In this technique bubbles and aggregates are exposed to a monochrome progressive scan camera. The acquired images are directly stored in a computer connected to the camera for post-processing. The sampling apparatus consists essentially of a vertical tube for collecting bubbles, a viewing chamber and a collection chamber, where particles carried by the bubbles are released. The function of the collection chamber is to maintain the viewing chamber clear for imaging purposes. Each image is automatically processed off-line, using digital image tools. In this paper the advantages and limitations of this new technique are described."

Jan 1, 2003

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By C. Raghu Kumar

Hydraulic or teetered bed separators (TBS) are finding new avenues for application in the field of mineral processing. Floatex Density Separator (FDS) is a hydraulic/teetered bed separator capable of operating at high tonnage due to its advanced instrumentation. FDS/TBS is being used in Indian mineral sand industry for classification and segregation of different minerals. The purpose of this paper is to provide details on the performance of the plant scale FDS in recovering the chromite from feed (below 1mm size). Historically this feed has been processed using hydrocyclones and spiral classifiers; however, there is a strong trend now to employ teetered bed separators, thus allowing significant changes to be made in the plant for improving process efficiency. In the present work, the performance of the plant scale FDS is described in terms of partition curve (yield, cut size, classification efficiency/Ep) for different combination of process variables and also in terms of metallurgical grade and recovery. It is found that, efficient classification can be achieved at a maximum cut size of 380 µm with and the imperfection is also reported as low as 0.16. The grade of the underflow product is enriched as maximum as 52.2% Cr2O3 from a feed assaying 40.4% Cr2O3.

Sep 1, 2012

By W. Z. Zu

In proved reserves of vanadium-containing titanomagnetite in Panxi, China, iron grades of ores were 50% ~ 15%. China?s metallurgical industry departments defined the iron ores containing 50% ~ 20% TFe as exploitable resources and the extreme lean iron ores containing 20% ~ 15% TFe as temporary unexploitable resources, the extreme lean ores were as waste rejected into waste dump in mining process. This paper researched process mineralogy of the extreme lean ores, adopted mineral processing technology responded to the properties of the ores to treat the ores and obtained quality vanadium-iron concentrate, titanium concentrate and sulfur concentrate, therefore successfully utilized the extreme lean ores, changed the ores from waste resources to exploitable resources.

Jan 1, 2014

By V. Sovmen

The gold-ore Olympiada deposit is located within the Yenissei range (Krasnoyarsk Region, Russia). Primary sulphides ores are metasomatic changed rocks, mica-calcite-quartz structure with impurity amphiboles, chlorites, carbon, the rare thin grains of sulfides (up to 3%~5%) and native gold. The structures of ores are fine-grained, prevailing texture of ores - interspersed, vein-interspersed, band-interspersed, veinlet. The most important minerals in the deposit are: gold, arsenopyrite, pyrrhotite, antimonite, Sb-sulphosalt, quartz, muscovite, calcite, siderite, titanium minerals, chlorite and minor sulfides like chalcopyrite, galena, sphalerite, etc. A common problem in mineralogical studies applied to mineral processing (concentration, cyanidation, etc.) is the characterization of gold in ores and technological products. This paper discusses the behavior of minerals during technological process at operating factory in Olympiada Mine and gold distribution in the ores and products. For the mineralogical characterization of minerals ? combination of analytical techniques was used. Gold is encountered in the primary ores as free grains among rocks, growth with sulfides and nonmetallic minerals, inclusions in sulfides, sulphosalt, and nonmetallic minerals. The gold-sulphide ores of Olympiada deposit can be quite complicated for enrichment. With the purpose to increase the extraction of metal from concentrates by liberating the dispersed gold, forming inclusions in sul-fides, there is used technology of biooxidation of flotation concentrates in Olympiada Mine. Gold and the basic ore-forming minerals in the ores feed, sulphidic concentrates, biocakes, tailings of concentrates of flotation and products of hydrometallurgical leaching have been studied in the mineralogical research. During researches it is established that pyrrhotite was completely oxidized while arsenopyrite was oxidized almost completely in the bacterial oxidation process. Pyrite and antimony minerals behave similarly and were oxidized only partially. The main oxyhydroxides in the bacterial oxida-tion process are goethite, limonite and jarosite. The results of mineralogical researches showed reasons of losses of gold during hydrometallurgical enrichment.

Jan 1, 2014

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By P. Knüpfer, B. Babel, M. Rudolph, F. Perez Maldonado, U. A. Peuker, L. Ditscherlein

"In heterocoagulation processes for the separation of mineral particles, the most famous being froth flotation, the main characteristic of separation is a differing wettability of the constituents to be separated. This most crucial property in the economically important process of flotation is often only and incompletely, quantitatively described in terms of contact angles against water. A water contact angle larger than 90° is referred to as hydrophobic and hydrophilic vice versa. Looking at Young’s equation shows that it is actually the surface energy of the solid in interaction with the surrounding phases and their surface energies (or surface tensions for liquids) which describes whether there will be hydrophobic/hydrophilic hydration interactions leading to attraction or repulsion. This, we have previously published for various more or less hydrophobic minerals in correlation to their flotation response, i.e. flotability (c.f. Rudolph & Hartmann, Coll.Surf.A 513, 380-388). In the same paper we also discussed the heterogeneity of wettabilities as assessed with the novel method of inverse gas chromatography. Furthermore we have also reported on hydrophobic force distributions as assessed with atomic force microscopy which are as well due to wettability heterogeneities (c.f. Fritzsche et al., Coll.Surf.A 459, 166-171).In this paper we present wettability distributions of different substrates and particles with various surface roughnesses/shapes and degrees of hydrophobization as assessed with iGC, AFM and dynamic sessile drop analyses. We are putting the results in context in unifying models and present methodologies helpful to make use of the fundamental information and their impact on the actual industrial separation process in fundamental process models. Besides froth flotation we also emphasize the impact on selective hydrophobic flocculation process."

Jan 1, 2018