Search Documents

With shortage of sulfide nickel ores, laterite ore was paid more attention by scientists. Because its grade is commonly lower than sulfide nickel ores, laterite ore can not be utilized effectively be-coming the bottleneck of study. Leaching laterite ores from Yuanjing, Yunnan province, organic ac-ids show better selective than sulfide acid in nickel and cobalt recovery. Organic acid has low de-pendent on pH, keeping leaching capability even higher than 3. On the other side, when pH up to 2, sulfide acid can not leach laterite ores any more. After four kinds of organic acid leaching laterite ores, besides citrate, malate and succinate have good leaching and effectively selective capability. Especially, succinate has the best selective leaching capability of nickel and cobalt in four kinds of organic acids for latter anion purification and separation. Isolated from waste water with sugar, Aspergillus niger (zs1) has great capability to produce organic acids and vigorous growth. Laterite ores have been respectively processed by direct-leaching and indirect-leaching. Indirect-leaching gives a better result than direct-leaching. Extraction of nick-el by indirect-leaching reaches 44.3%, far more than that of direct-leaching. Moreover extraction of nickel at pulp density of 5% is higher than that at pulp density of 10%, reaching 63% in 11 days and extraction of cobalt also is 48.1% in the same period. Compared with nickel and cobalt, iron gives low extraction in solution, containing organic acids produced by Aspergillus niger .

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By A. J. Ren

The ore, dealt with in this paper, is a certain rutile in Shanxi province, China. A trunk flowsheet with gravity concentration is used, and the TiO2 grade of rutile concentrate is about 90%, but the TiO2 recovery is less than 50%. In order to increase the rutile recovery, the laboratory test, using the truck flowsheet with flotation, is carried out. The flowsheet is that firstly floatable gangue is re-moved by flotation; secondly rutile is recovered by flotation; and thirdly impurity is separated by LIMS, HIMS, gravity concentration and flotation from the rutile concentrate. In rutile flotation, BK423, a phosphonic acid, is used as rutile collector, and Na2SiF6 is used as silicates depressant. The experimental result shows that the recovery of rutile concentrate is improved obviously, and the recovery of ultimate rutile concentrate is 68.01% TiO2 and 84.88% rutile. The TiO2 grade of first concentrate is 95.98%, and the TiO2 recovery is 45.60%. The TiO2 grade of second concentrate is 80.53%, and the recovery is 22.41%. Furthermore, magnetite and ilmenite are recovered in the flowsheet.

Jan 1, 2014

By de Vaux. D.

Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis. The results obtained have demonstrated that water quality does play a significant role in flotation recovery at the experimental conditions used.

Jan 1, 2003

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By de Vaux. Deryck, Natalie J. Shackleton, Vratislav Malysiak Cyril T. O. Connor

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. This investigation aimed at reducing surface passivation of pentlandite and inadvertent activation of pyroxene, thereby improving ultimate valuable mineral recovery and selectivity. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion.The addition of diethylenetriamine (DETA) reduces the copper concentration on both minerals, predominantly on the pyroxene surfaces and polyphosphate further enhances the selectivity at pH 6.The microflotation and batch flotation data obtained has shown a significant improvement in the ultimate flotation response of valuable mineral recovery and concentrate grade compared to the standard reagent regime, while the continuous flotation results significantly improved the selectivity, however, at a similar ultimate recovery."

Jan 1, 2003

By A. S. Broesder

"With depletion of global ore deposits, there has been an increasing industry trend towards mining of lower average grade deposits in order to meet global demand, resulting in increased processing cost, energy usage and water usage. Consequently the industry is seeking pre-concentration technologies to reduce costs, increase production in existing operations and potentially enable the economic mining of previously uneconomical deposits. This pre-concentration can also advantage downstream processing and metal recovery. CSIRO has developed a large scale magnetic resonance based technology for the rapid quantitative detection of selected copper, iron and arsenic minerals in bulk ore. The technology is suited to measurement on large primary conveyors for enabling “pod” based sorting. The approach used in high tonnage sorting is to not sense and divert individual rocks, but to instead measure groups of rocks (“pods”) carried continuously on a single primary conveyor that can be diverted by conventional mechanical means. Bulk ore sorting operates by removing barren ore pods from a stream of crushed ore based on a bulk sensor measurement at a pod resolution of ~1 – 10 tonnes. The sorting process is based on the intrinsic variability of grade during the mining process that often occurs at the few tonne scale, and for instance, is common in many porphyry copper deposits. The MR technology has been proven in the laboratory for a wide range of copper, arsenic and iron minerals. A full scale prototype sensing system has been demonstrated in a trial at an Australian copper mine. Implementation trials of commercial MR based bulk sorting systems are progressing during 2018.INTRODUCTION An increasing trend in the mining industry is the exploitation of larger lower-grade deposits to meet global demand. Low-grade deposits involve increased processing cost, energy and water usage and increased tailings. There is therefore growing interest in technologies that enable more efficient extraction of low grade deposits. Water intensity of mining activities in a context of water scarcity, and the environmental and health implications of mine tailings are existing challenges, which are only made worse by the progression to lower grade orebodies. There is therefore also an interest in safer, cleaner and less wasteful extraction and production to ensure community well-being and environmental resilience."

Jan 1, 2018

By G. X. Du

Reaction kinetics of serpentine and hydrochloric acid is theoretical basis for optimizing reaction process conditions of serpentine and hydrochloric acid. Kinetics of serpentine and hydrochloric acid was studied in this paper. The results indicated that apparent reaction order to hydrochloric acid was two and reaction kinetic equation could be expressed as: 2HClHCl,ddtckct-=·. The diffusion rates of hydrogen ions in liquid film on surface of serpentine particle and in amorphous silica layer generated in the reaction and chemical reaction velocity during the reaction had important effects on to-tal reaction velocity. And chemical reaction velocity had the most significant influence. The relation of conversion rate of magnesia xMgO with reaction time could be expressed as: 1(1)xkt--=·.

Jan 1, 2014

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation behavior are just a few of the parameters that are largely due to the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the inherent impact of surface wettability in nearly all industries, fields, and multi-phase interactions, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In this study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Z. A. Zhou

In Canadian oil sands processing, flotation is used to recover liberated bitumen droplets from oil sands slurries. Similar to conventional mineral flotation practice, a fundamental limitation of recovering bitumen from low grade oil sand ores is its slow and ineffective aeration of the liberated small bitumen droplets. Gas nucleation and cavitation could provide better mechanisms for accelerating bitumen-bubble attachment. A research program was undertaken to examine factors affecting spontaneous bubble nucleation on bitumen surfaces. The results demonstrate that surface hydrophobicity and existence of gas nuclei in process water play a critical role for bubble nucleation. While there are more bubbles nucleated on highly hydrophobic silanated glass surfaces than on moderately hydrophobic bitumen, bubble nucleation on clean hydrophilic glass surfaces is negligible. Heating process water up to 85 ~ 95oC (as used in commercial operation) or boiling tap water prior to gas nucleation tests is shown to remove sufficient amount of gas nuclei existing in the water, thereby drastically reducing the number of bubbles nucleated on bitumen. Enhancing gas nuclei formation in hot process water is identified as a promising strategy to improve bitumen-bubble attachment during oil sands conditioning, and hence to increase bitumen recovery from low grade ores.

Jan 1, 2014

By J. Yianatos, C. Matamoros, F. Díaz

The non-selective entrainment of fine solids in flotation equipment has a detrimental effect on the concentrate grade. Reduction of solids entrainment (upgrading) is typically related with a loss in recovery of valuable minerals. For improving the froth transport characteristics and flotation cells design, a better understanding and quantification of the actual solids drainage and entrainment processes are required. In this work, the study of solids transport in the froth of a two-dimensional flotation cell was performed. The prototype cell represents a radial section of an industrial flotation cell (130m3) and was operated at steady state. Experimental tests consisted of adding a small amount of radioactive solid tracer (0.3g) near the top-of-froth or near the bottom of froth (close to the interface). The solid was selected as a non-floatable mineral (gangue) in order to evaluate both the solid entrainment into the concentrate as well as the solid drainage into the collection zone. Solid tracer consisted of fine or coarse gangue particles, P80 of 35 and 120 µm, respectively. Twelve collimated sensors located along the froth and collection zones allowed the evaluation of the solid transport in the froth, and the solid drainage from the froth to the collection zone, after tracer addition at different distances from the discharge lip. Results showed that longer distances to the froth discharge lip, as well as higher particle sizes, promotes higher solid drainage from the froth to the pulp zone, while decreasing the solids entrainment into the concentrate. The same result was observed for the solid located near the top-of-froth as well as near the bottom of froth. This information was complemented by the froth surface velocity measurements, using the Visiofroth system, showing a good agreement between the froth bubbles velocity and the solid transport velocity, measured near the discharge lip.

Jan 1, 2018

By Gülay Bulut, Ferihan Göktepe

Pyrite is the most abundant and widespread sulphide mineral and its flotation has been investigated by many researchers. It is well known that, pyrite is floatable under acidic conditions and recovery drops with increase in alkalinity due to changes in solubility of iron hydroxides on the pyrite surface. Most of the works also revealed out that pyrite displays variable behaviour in flotation circuits. This behaviour mainly related with origin and mineralogical composition of ore, liberation size, electrochemical behavior of minerals constituting ore, the trace and minor element content of the mineral, texture, application variables belonging to flotation circuits. In this study, copper activation effect was examined on different origin of pyrites. The experiments were performed with five high grade samples of pyrite from the different mining districts of Turkey. The pyrite samples were different from each other with respect to either their physical or chemical properties; they were different physical appearances and contained different associated minerals. In the micro-flotation tests, 1x10-4 mole/L copper sulphate and 1x10-4 potassium ethyl xanthate were used as flotation reagents. First of all pyrite samples were floated using only xanthate at different pH. Results showed that best floatation results obtained at acidic pH range for all pyrite samples. When copper ions were used to activate, all pyrite samples floated at neutral and basic pH values, too but depending on the samples, recovery and pH ranges were slightly changed.

Jan 1, 2014

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

Different hydro-metallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2. An innovative acid reductive leaching carried out in mild experimental conditions was here considered using agricultural and industrial wastes containing carbohydrates as reducing agents. The leaching process was investigated from a kinetic and equilibrium point of view in order to optimise the experimental conditions, develop a kinetic model and obtain high purity concentrated MnSO4 solutions. To study the leaching kinetic a Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis before and after leaching. Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydro-alcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions.

Jan 1, 2003

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

By S. S. Lu

In sodium oleate and salicylhydroxamic acid systems, sequence of floatability of three sulfate minerals is: barite>celestite>gypsum, in lauryl amine system is: gypsum>celestite>barite. XPS and infrared spectrum analysis are used to find that it is chemical reaction between sodium oleate and three minerals, physical adsorption on the surface of minerals for lauryl amine, and it is chelating reaction between salicylhydroxamic acid and three minerals possibly. Theoretical calculation on chemical bonds in crystal structures of three minerals is carried out, finding that breaking degree of Mn+?O2- in crystal structures of three sulfate minerals is closed related with floatability.

Jan 1, 2014

By S. Z. Khan, Veerendra Singh, Y. Rama Murthy, S. Prasad, Sunil Kumar Tripathy, Gajanan Kapure

"In this study, a low-grade ferruginous low-grade chromite ore was subjected to reduction roasting by using conventional heating as well as microwave heating. Sukinda chromite ore deposit contains majorly iron-bearing minerals as gangue phase. The magnetic susceptibility of these minerals enhances effectively after reduction roasting. Alteration of crystalline structure and magnetic property of these metals enables separation of low-grade ore by using magnetic separation. Conventional roasting studies by varying the temperature, time of reduction and reductant dosage were changed for low-grade ferruginous chromite ore. Similarly, microwave power, retention/exposure time and reductant dosage varied for reduction roasting studies under microwave environment. It is found that low-grade ferruginous chromite ore can be upgraded by reduction roasting and 61.2% Cr2O3 was recovered with a chromium-to-iron ratio of 1.93 from feed chromium-to-iron ratio of 1. Microwave reduction roasting studies resulted in upgradation of chromium-to-iron ratio to 1.73 with a recovery of 21% Cr2O3.INTRODUCTION The chromite ore occurs as a spinel containing oxides of chromium, iron, magnesium and aluminium. Most of the Indian chromite deposits are of ferruginous (rich in iron content) which indicates the abundance of ferruginous gangue minerals along with chromite. The primary use of chromite ore is towards the production of ferrochrome alloys. Chromite ores with less than 40% Cr2O3 and the chromium-to-iron ratio (Cr-to-Fe ratio) <1.8 is considered to be unsuitable for the smelting process (Tripathy et al. 2012, Tripathy et al. 2012a). A considerable amount of low-grade chromite ore and overburden excavated during chromite mining is getting accumulated every year, causing a threat to the environment. Its disposal poses a significant challenge and, hence, the beneficiation of low-grade chromite ore and its utilisation has been attracting a lot of attention. Different physical method of beneficiation methods is generally employed for the improvement of the Cr-to-Fe ratio (Tripathy et al. 2012, Murthy et al. 2011, Tripathy et al. 2012a, Tripathy et al. 2013, Tripathy et al. 2016, Tripathy et al. 2017, Tripathy et al. 2017a). It is observed that the enrichment of the chromite ore is carried out by using gravity and in some places by magnetic separation. However, the enrichment of Cr-to-Fe ratio from low-grade ferruginous chromite ore is difficult by using the above-mentioned beneficiation methods due to the presence of near gravity and near-magnetic susceptibility minerals along with chromite. However, an alternative beneficiation method is needed to explore for the beneficiation of such mineral deposits. Reduction roasting followed by magnetic separation is an alternative option for the separation of these types of ores which is widely reported for the iron and manganese ore (Li, et al., 2010; Chun, et al., 2014, Rath et al., 2018). These processes are majorly focussed on differentiating the magnetic susceptibility between minerals and subsequent separation by using magnetic field. The main advantage of such method is dry process option along with the pre-processed product for the costly smelting process. Also, the roasting of minerals in a microwave environment is also an active research topic in the recent time. So, the amenability of the separation feature of the roasting process by using conventional heating as well as microwave heating can be can be studied for the low grade ferruginous chromite ores."

Jan 1, 2018

By Pamela Castillo, Marcia Muñoz, Rodrigo Luca, Brian Townley, Fernando López

In the present study we discuss the value of multi-element geochemistry as a tool for semi-quantitative to quantitative bulk mineral characterization in geological and geo-metallurgical modeling of porphyry copper type deposits, with an emphasis on hydrothermal alteration associations, types and intensities. In mine production of porphyry copper deposits much effort is placed on ore grade and geological modeling, applied for predictive mineral processing behavior, from blasting, grinding, leaching or flotation, down to waste disposal and environmental management. High confidence geological models are commonly based on geological mapping of drill core and surface/ underground exposures, combined with discrete mineral characterization (e.g., petrography, QEMSCAN®, spectroscopy, etc.). Unfortunately these are expensive and applied to limited numbers of samples, thus lacking sufficient representation and not suitable for geo-statistical modeling. In addition, geological mapping always presents uncertainty, based mostly on qualitative estimates. The combination of information usually provides geological models that are hard to combine with geo-metallurgical data, much less with mineral processing predictive behavior models. The advent of multi-element geochemistry, at low cost, has allowed employment of such tools massively, yet little use is given to the data, usually focused on elements of economic interest (main ore and credits) and elements of negative impact to concentrates and/or process. Geochemistry reflects the mineral composition of rocks, thus allowing characterization of lithology, alteration types and intensities, and mineralization. As examples of such applications we present generic classification techniques which were developed on various porphyry copper deposits of northern Chile, these based on multi-element geochemistry, allowing for semi-quantitative to quantitative high resolution modeling of key aspects of lithology, hydrothermal alteration and mineralization, and which may be cross-referenced to metallurgical test samples and by that, to geo-metallurgical properties of rocks and modeling. In addition, as data is quantitative and continuous, modelling of gangue can benefit from geo-statistical modeling.

Jan 1, 2018

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By E. D. Gálvez, L. A. Cisternas, R. Acosta-Flores, F. A. Lucay

The optimal design of flotation circuits is a complex task as the mathematical model is nonconvex and includes binary variables, making it difficult to obtain the global optimum solution. Furthermore, there are epistemic uncertainties in the evaluation of the performance of flotation and grinding units. This epistemic uncertainty is generated because semi-empirical models are used with parameters that are a function of the circuit design. Therefore, it is not possible to adjust these models based on experimental data as the experimental conditions are not known at the design stage. This paper analyzed the effect of the uncertainties in flotation units, grinding units, and both units simultaneously. As a result, this paper demonstrated that, for a specific mineral, few structures exist that are optimal for a wide range of values in flotation stage recoveries and liberation fractions in the grinding units. A remarkable aspect of this work is that it introduces grinding, one of the operations that most influences energy consumption in mining and has not been studied in depth in the design of flotation circuits. To demonstrate that there are few optimal structures for a specific mineral when there is high uncertainty in the process units, an a priori approach or first principles was used. Two methods of proof were used: proof by construction and proof by exhaustion. Proof by construction is the construction of a concrete example with a property to demonstrate that something having that property exists. In this work, two examples were considered in the proof by construction. In proof by exhaustion, the conclusion was established by dividing it into a finite number of cases and proving each one separately. Here, 30,000 cases were included for each example. This knowledge can be useful in circuit design including grinding, e.g., after selecting the circuit (or the most promising circuits), and the equipment design parameters and operating conditions can be defined based on simulation and laboratory tests.

Jan 1, 2018