Search Documents

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Tu Bao

HP-Pile foundations are the most favorable type of foundations for bridges because of their constructability, versatility with regard to subsoil conditions, and settlement controllability. For many years, bridge engineers have puzzled over the most economical way to orient HP-Piles: Should the strong axis be oriented in the longitudinal direction or in the transverse direction? The accurate design of foundations may considerably reduce construction costs. In order to answer this question, 3-D finite element models will be set up to analyze the effects of pile orientation on bridge behavior. Because seismic loading usually controls the structural design in seismic zones, it is important to investigate the effects of pile orientation under such loading. HP-Piles are designed conservatively due to the uncertainty of the dynamic soil-structure interaction during earthquakes. For the bridge substructure, the soil?s stiffness plays an important role in load distribution as the soil and piles act as a combined system to resist the seismic loading. The dynamic soil-structure interaction mechanisms of bridges in both the longitudinal and the transverse directions will be investigated through the use of 3-D finite element models. The numerical models will realistically simulate the soil-pile-abutment-wingwall-superstructure system subjected to seismic loads. Nonlinear soil springs will be employed to model the non-elastic soil behavior. The analysis will provide theoretical support to the design practice. KEYWORDS: HP driven piles, finite element, pile orientation, soil-structure interaction

By Andrew Rietz, Yu Bao, Steven Halewski

"HP-Pile foundations are the most favorable type of foundations for bridges because of their constructability, versatility with regard to subsoil conditions, and settlement controllability. For many years, bridge engineers have puzzled over the most economical way to orient HP-Piles: Should the strong axis be oriented in the longitudinal direction or in the transverse direction? The accurate design of foundations may considerably reduce construction costs. In order to answer this question, 3-D finite element models will be set up to analyze the effects of pile orientation on bridge behavior. Because seismic loading usually controls the structural design in seismic zones, it is important to investigate the effects of pile orientation under such loading. HP-Piles are designed conservatively due to the uncertainty of the dynamic soil-structure interaction during earthquakes. For the bridge substructure, the soil’s stiffness plays an important role in load distribution as the soil and piles act as a combined system to resist the seismic loading. The dynamic soil-structure interaction mechanisms of bridges in both the longitudinal and the transverse directions will be investigated through the use of 3-D finite element models. The numerical models will realistically simulate the soil-pileabutment- wingwall-superstructure system subjected to seismic loads. Nonlinear soil springs will be employed to model the non-elastic soil behavior. The analysis will provide theoretical support to the design practice.IntroductionAs sustainability has asserted itself in the public’s eye, bridge professionals have rushed to develop criteria for sustainable bridges. The three main categories that define and distinguish sustainable bridges are: lower energy input, increased durability, and simplified deconstruction. By optimizing the structural members, the engineer is able to reduce the material quantities for the bridge, effectively reducing the energy input for the bridge (Hunt; Whittemore). A deeper understanding of soilfoundation- structure mechanism will facilitate sustainable bridge design by lowering energy input and increasing the service life of bridges (Rietz et al.)."

Jan 1, 2017

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Albert Neumann, Franz-Werner Gerressen, Giancarlo Santarelli

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. In addition they are also quite often used as deep groundwater barriers, named Cut-Off-Walls (COW). Due to the requirements of each particular job site, e.g. the need for carrying high loads or as seepage barriers, there is an increasing industry demand for efficiently cutting into rock. Besides the removal of boulders, cutting through rock, is always the most difficult part of the excavation process of a diaphragm wall or COW.There are a number of influencing factors which have an impact on the rock cutting performance. Besides the influence of the rock characteristics itself, which is not always the same, there are other factors related to equipment, tooling as well as the operating staff. In addition to RQD, the most commonly available rock property found in geotechnical reports is the Unconfined Compressive Strength (UCS) value. There are however some other related properties, such as weathering, bedding, inclination, abrasiveness, etc.,which can have a major impact on the achievable cutting performance. This paper will discuss the various parameters, and how they can be considered for performance estimation. Based on experiences gained on over 100 projects, a performance estimation chart was developed to allow for a better approach to these kinds of projects. This paper also explains the general installation process in as well as some specific features related to specific site conditions. In addition, some job site references will give more detailed information about such type of site conditions and how to deal with them.Keywords: Diaphragm wall, Cut-Off-Wall, Trench Cutter, RockINTRODUCTIONDiaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits, shafts, permanent foundation walls and load bearing elements.It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions.In addition diaphragm walls can also be used as deep groundwater barriers (Cut-Off-Walls). This market has demonstrated that the demand for these types of walls is reaching ever more difficult soil conditions and greater depths which are surpassing the current industry standards. The trench cutter is the most important tool for performing this type of work."

Jan 1, 2016

By Amalia Giannakou

When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.

By Orestis Zarzouras, Amalia Giannakou, Jacob Chacko

"When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.IntroductionThe Izmit Bay bridge, a 3-km-long suspension bridge that crosses Izmit Bay in Turkey, is planned to be constructed in one of the most seismically active places in the world. The south approach structures for the Izmit Bay Bridge along the western side of the Hersek peninsula bring the bridge down from on the order of El. 60 meters at the South Anchorage to an elevated embankment approximately 1.3 km farther south (Figure 1). The south approach structures are located within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The concept design team has developed a concept design for a “viaduct” structure that consists of 10 spans with lengths varying between 136 m and 100 m and two back spans one of 125 m, attached to the main bridge and the other of 74 m attached to the south embankment."

Jan 1, 2017

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By Lori A. Simpson

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the three-level basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tied-back soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

By Rahul Wankhade, Sunil S. Baswankar, Aditya S. Kharatkar

Despite advances in pile design methodologies and piling techniques at site, difficulties and uncertainties still exists for design of piles particularly in coralline deposits and weak carbonate rocks. Such deposits are known to be heterogenous in nature, and occupy major stretches of earth, where piling experiences are probably very scanty. Such deposits are associated with low unit weights and usually consist of weakly cemented calcareous and carbonate soils interbedded with coral rocks containing cavities, which are completely void or filled with coral debris. Many of the studies indicate that conventional parametric relationships are may not apply to such sediments and rock formations. This paper intends to provide an appraisal of the available information that cautions against risks involved in conventional design practice and also serve as a guideline for pile design in such formations despite being a grey area of research. Contents of the paper is expected to provide a basis for the pile design and likely to serve as an eye-opener for research into this important soil-pile structure interaction problem.

Sep 1, 2022

By Gilbert R. Tallard

"Pouring deep foundations by the tremie pipe method is nowadays such a common process that it has becomes an unspecified practice. Means and methods are almost entirely at the contactor’s discretion. A variety of practices are permitted and seldom associated with the discovery of abnormalities and areas of random defects in concrete. This writer wishes to call the attention of stakeholders to the initiation details of the tremie pour operation.KEYWORDSINTRODUCTIONThe advent of slurry as a means of shoring an excavation of relatively small cross section but of possibly great depth has become part of state of the art in foundations construction, with the substitution of said slurry by concrete to provide the structural end product element through the use of tremie pipes. In appearance, there is nothing more simple than pouring concrete into a tremie pipe through a hopper after the basic work has been done i.e. the excavation or drilling, the cleaning of the slurry, the placement of the reinforcing cage, then the tremie concrete pour is almost a reward for a successful achievement. Force of habit has removed the awareness on the process fundamentals for initiating the pour; a variety of practices used call for a review and a reassessment as a means of reducing construction defects that may result from flawed practices, and and especially we are pouring deeper holes. This writer intends to address this issue focusing both on the drilled shaft and the diaphragm wall industries.TREMIE PIPES AND HOPPERSA tremie pipe diameter needs to be sufficiently large to allow the rapid descent of concrete with a minimum of friction loss and avoiding possible bridging in relation to aggregate size. Impervious joints between pipe sections are essential to prevent slurry “raining” over the concrete which can cause concrete segregation pockets and possibly plug the pipe with damaging consequences. That tremie pipes be long enough to reach the bottom may be self-evident but poorly written specifications can be erratic on that subject and seldom specific in terms of inches. A standard pipe of 10 inches is well accepted throughout the foundations industry; double O rings and spline joints are common and function well if properly maintained. However the practice to cover the joint with the ineffable duct tape indicates that all is not always well with this detail. Also, spline cables may shear in case of very long tremie pipes causing the separation of the tremie pipe requiring a restart in midstream with another probable source of inter mixing of concrete and slurry with subsequent defects."

Jan 1, 2017

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By Theodore W. Vogelpohl

Augered cast-in-place piles have proven to be effective, adaptable and economical for projects throughout the Ohio River Valley. Specifically, they have been used extensively for high-rise structures, sports stadia and large commercial developments along the Cincinnati, Ohio and Northern Kentucky Riverfront. They have been designed and utilized as relatively short toe resistance piles in bedrock, and intermediate to long toe and shaft resistance piles in granular outwash deposits above the bedrock. They have been designed for large axial compression loads as well as moderate axial tension loads and lateral loads. This paper presents a few load test results that demonstrate the range of capabilities of augered cast-in-place piles in the variable subsurface profile along the Cincinnati, Ohio/Northern Kentucky Riverfront.

Jan 1, 2005

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By Ed Kase

Cross-hole sonic logging (CSL) has become the universal standard, nondestructive testing (NDT) method used in evaluating the integrity of foundation structures to maintain quality assurance and quality control (QA/QC) of transportation facilities and infrastructures. Tomography, based on three-dimensional cross-hole sonic logging data processing technology, offers an improvement over the techniques currently used to characterize the interior structure of drilled shafts. The underlying concept for seismic tomography is based on the principle that acoustic waves propagate at different velocities through different types of material or the same material with different physical properties. Three-dimensional velocity tomographic images provide greater detail of the interior structure, making defects easier to classify with respect to size and location within the foundation structure. By accurately classifying these defects, an engineer has the information necessary to accurately assess whether these structures meet the applicable design requirements, allowing them to repair or replace inadequate foundation structures. The end result is that the foundation structures will meet the safety and service life requirements for their project. This paper will present applications of seismic tomography, illustrating how seismic imaging can provide accurate information regarding the integrity of foundation structures.

Jan 1, 2003

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000