Search Documents

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Michael T. Lambert

The purpose of the this paper is to demonstrate the benefits of using additional instrumentation during load tests of auger-cast-in-place piles. Traditionally, only load and butt displacement are determined during load tests. The results from and methods used to instrument 15 auger-cast-in-place (ACEP) piles as part of six projects are included herein. By instrumenting the piles, the distribution of load along the pile length and load transfer can be determined, allowing the pile capacity to be adjusted or the length/diameter of the pile to be adjusted for the a given required load. The majority of the piles tested were designed as end bearing piles on either shale or limestone bedrock. No discussion of Geotechnical Instrumentation can be started without acknowledgement of the "Red Book." The actual title of the book is Geotechnical Instrumentation for Monitoring Field Performance, by Mr. John Dunnicliff, John Wiley and Sons, 1993. Anyone undertaking an instrumentation program should thoroughly review the Red Book, paying particular attention to Chapters 3 and 4. Instrumentation should not be done just because it can be done. There must be an unanswered question or questions that can be answered with measured data before instrumentation should be considered.

Jan 1, 2000

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Richard D. Luark, Fernanda S. Madrona

Deep foundation construction in highly developed urban settings pose unique challenges of working with deep excavations in a relatively confined area while preserving the integrity of nearby structures. For construction of the below grade parking for two, 40-story residential high-rise towers, shoring walls were required to support the maximum 70-foot-deep vertical excavation in downtown Seattle, Washington. The design of the excavation support system consisted of soil nails combined with closely spaced vertical elements to allow the top row of soil nails to be installed up to 10 feet below the ground surface avoiding conflicts with adjacent underground utilities. To limit deflections next to a seven-story building, the upper rows of soil nails were post tensioned. An instrumentation program was implemented to monitor the deflections in the shoring walls by means of vertical inclinometers and optical survey monitoring. The shoring wall performance, designed to limit deflection to less than 1-inch to meet the City of Seattle requirements, was validated by the instrumentation program. This paper provides a discussion of the design and construction of the shoring walls as well as the monitoring data collected from the instrumentation system. PROJECT INFORMATION The project consisted of two residential high-rise towers, with five levels of below grade parking, located at 707 Terry Avenue Seattle, Washington. The project site covers a half city block, approximately 120 feet by 240 feet, and is bounded by Terry Avenue to the east, Columbia Street to the north, Cherry Street to the south, and an alley to the West. Prior to the development, site was occupied by surface parking. A 7-story concrete building with two stories of below grade parking, owned by the Archdiocese of Seattle is located just west of the 16-foot-wide alley. Numerous below grade utilities consisting of electrical, telecommunications, gas, water, sanitary sewer, steam, and storm drains, surround the project. The perimeter below grade parking walls extended within inches of the property boundaries. Topographic relief across the site was on the order of 8 feet. Figure 1 illustrates the site plan view.

Jan 1, 2019

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015