Search Documents

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017

Jan 1, 1984

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Larry Rayburn

Augercast piles evolved in the late forties from the process of pressure grouting open holes backfilled with stone. In 1956, a patent was issued for a cast in situ pile by pumping high pressure grout through hollow-stem, continuous flight auger as the auger is gradually withdrawn from the ground. The patent rights expired in 1973 and the use of auger-cast piles greatly expanded with most large deep foundation contractors now installing augercast piles. At one time augercast piles had a bad reputation, partly because of not having a blow count to give some engineers a confidence factor and there were some quality issues. Over the years the quality issues have been eliminated and I am sure the augercast is the most installed pile in private industry and is now being used by some State Agencies.

Jan 1, 2005

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

By Andres M. Baquerizo, Jeremiah J. Filjones, Nicholas Feldt

The Estates at Acqualina located in Sunny Isles Beach, FL, is comprised of two, ocean-front, 50-story, luxury towers with podiums and villas. With city regulations now requesting that above-grade floors be limited to commercial or residential units, parking facilities for the tower structures were situated within two levels of underground basement parking. However, ensuring dry excavation through south Florida’s highly pervious limestone, immediately adjacent to the beach where the groundwater table is very shallow, can be extremely challenging and costly for developers. In recent years, significant advances have been made to overcome this challenge with the innovative use of deep soil mixing to create a “dry hole”, assisting in the construction of foundations and underground usable space for parking, storage, etc. The “dry hole” system includes a soil mix bottom seal, with soil mix secant pile walls in combination with auger cast deep foundation elements to support the future structure. This approach enables groundwater control to greater depths than can be achieved by conventional sheetpiling and dewatering. For the Estates at Acqualina, a successful turnkey, design-build joint venture between two foundation and geotechnical contractors resulted in a dry excavation to 34 ft (10.4 m) below grade and to a record- breaking auger cast pile depth of 182.3ft (55.6 m), all within an aggressive 26-week schedule to deliver the “dry hole” excavation for the first tower. This presentation will discuss the logistics, quality control, design, and safety for the different techniques involved. INTRODUCTION AND BACKGROUND The Estates of Acqualina is a pair of 50-story luxury towers located on Sunny Isles Beach in Florida with a two-level underground basement for parking. The project’s location just steps away from the Atlantic Ocean, geology, and high-water table created a challenging project. The owner, Trump Group, contracted the joint venture of HJ Foundation and Hayward Baker (HJ/HB) to design-assist-build a system to control the groundwater, allowing the 2-story underground parking structure to be constructed. In order to accomplish this task, the JV utilized an installation technique known as deep soil mixing. This technique mixes the in situ material with a cement slurry to create a very impermeable material called “soilcrete”.

Jan 1, 2019

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Chu E. Ho, Paul Napoli

This paper presents the performance of nineteen open-ended steel pipe piles driven through highly variable overburden soils into glacial till and schist bedrock. The piles were 16 inches in diameter and 0.656 inches thick, with yield strength of 50 ksi. The piles were designed for a service capacity of 250 kips and were driven to achieve an ultimate geotechnical capacity of at least 500 kips. Due to the large variation in the ground conditions, installed pile lengths ranged from 25 to 66 feet. Some piles were driven to refusal on the bedrock while others were terminated at final driving resistance of 2 to 7 blows/in. Two piles were suspected to be plugged during driving while others did not. Each pile was instrumented with strain gages and accelerometers near the pile top, and observed using a Pile Driving Analyzer (PDA) to provide preliminary guidance on pile capacity achieved at end of initial drive (EOID). The influence of plugged and unplugged pile toe conditions on the interpretation of pile capacity was investigated using Case Pile Wave Analysis Program (CAPWAP). Characteristics of driving energy, compressive and tensile stresses developed in the steel pipe piles, and the resulting pile deformation behavior are discussed. INTRODUCTION The Hunters Point South redevelopment in Long Island City, Queens is one of New York City’s major efforts to transform former manufacturing zones into mixed developments for the middle-income community. The site is located along the eastern shoreline of the East River and Newtown Creek. The development included low to high-rise residential buildings, a public school and retail structures. Open spaces were created along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community related activities. Waterfront structures included small park buildings, walkways and viewing platforms with the shoreline protected by revetments as part of the City’s flood mitigation strategy. The project was implemented in two phases, with completion of construction for Phase 1 in 2013 and Phase 2 in 2019. Based on available historical information, extensive reclamation took place between 1855 and 1898. After 1951, changes to the shoreline were made along the East River, including the removal of reclaimed land along the northern portion of the project site to allow for docking facilities. By 1977, these facilities had been demolished and backfilled to form the current shoreline configuration. The present site was temporarily used as a parking lot with stockpiles of fill mixed with construction demolition rubble, rip-rap and boulders of varying heights across the site. The existing ground surface varied significantly up to approximately 25 feet difference in elevation. The stockpiles were removed and the site was re-graded during final development of the project. This paper discusses the foundation design challenges due to the loose overburden soils and potential obstructions within the fill material, in particular, the issues relating to installation of open-ended steel pipe piles through the ground conditions encountered on site.

Jan 1, 2019

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By Peter Cali, David Yang, Rakshya Shrestha, Ralph Griffin, Sushil Kafle, Motoji Watanabe

"As a part of the ‘US Army Corps of Engineers - New Orleans to Venice, Louisiana Hurricane Protection Project’, deep mixing ground improvement was designed to reinforce the soft ground for the emergency repair of a 7297-foot (2,224 m) long section of the Mississippi River West Bank levee in Buras Levee District under the contract ‘Emergency Levee Repairs – Contract P-17A, Plaquemines Parish, Louisiana’. The ground improvement utilizes a series of soil-cement panels oriented in the transverse direction of the levee. Each soil-cement panel consists of overlapped columns installed by the deep mixing method (DMM). DMM is performed from the existing top of levee and extended to competent stratum at depths varying from 26 feet (7.9 m) to 47 feet (14.3 m) below the working platform. The main purpose of the DMM panels is to provide shear resistance to the levee against lateral loads at high flood water condition. The DMM panels support the additional vertical load created by the increased height of the levee for hurricane protection and control the long-term settlement of the remediated levee, which might otherwise occur due to the compression of soft foundation soils. The total amount of DMM treatment is approximately 54,000 cubic yards (41,500 cubic meters). This paper reviews the project background, subsurface soil conditions and presents the design, construction and quality control of the deep mixing work for this levee repair project.INTRODUCTIONIn August 2005, Hurricane Katrina caused major damage to the federal and non-federal flood control projects in southeast Louisiana. In September 2005, Hurricane Rita caused further damage to this flood protection system. In an effort to minimize further damage and to enhance the protection level, certain non-federal levees located on the west bank of the Mississippi river in Plaquemines Parish, Louisiana were incorporated into the New Orleans to Venice Hurricane Protection project by the US Army Corps of Engineers (USACE). DMM techniques were then utilized by the USACE in several of these emergency projects and in many medium sized projects between 2006 and 2010 (Bruce et al. 2012). This project (called P-17A hereafter) which forms a part of this protection system is executed under the contract Emergency Levee Repairs, Contract P-17A. This is one of the largest projects of the USACE after LPV- 111. The huge LPV-111 project (5.5 miles (8.9 km) of levee) treated by DMM), the largest DMM project ever conducted outside Japan, began in 2010 and was completed in 2012 (Cali et al. 2012, Bruce et al. 2012).DMM is utilized at P-17A to construct a series of soil-cement panels oriented in the transverse direction of the existing levee to provide shear resistance to the levee against the lateral load during high flood water condition. The project extends 7297-foot (2,224 m) along the West Bank Levee of the Mississippi River in the Buras district of Louisiana, parallel to Louisiana Highway 23 (LA-23) as shown in Figure 1. It is located approximately 60 miles (96 km) south-east of downtown New Orleans."

Jan 1, 2015

By Sushant Upadhyaya, Deniz Karadeniz, Ahmed Mohamed

Soil setup analysis provides opportunities for efficiencies in pile foundation design and installation. Soil setup gain with time was evaluated as part of the foundation design and installation for twelve bridges along the Interstate 64 corridor between York County and Newport News in Virginia. The substructure elements of the bridges consist of driven precast prestressed concrete piles or H-piles. This case study describes lessons learned to understand the soil setup phenomenon during the installation of the piles in coastal plain. We were able to make expedited decisions during construction by analyzing previously performed pile dynamic analyzer (PDA) test results within the project alignment. Data evaluation included analyses of PDA data obtained from initial driving and restrike after a few hours to 5 weeks. The test data showed pile resistance increase up to twice in most cases and as high as four times in some cases. Foundation design and acceptance based on soil setup can provide opportunities for cost savings and advanced scheduling during construction.

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By Kazunori Matsushita, Masaru Sakakibara, Kenji Harada, Naotoshi Shinkawa, Mitsuo Nozu

The Sand Compaction Pile (SCP) method has been widely used as a typical countermeasure against liquefaction in Japan, and its effectiveness has been confirmed in many case histories of damages caused by the past large-scale earthquakes. A series of studies were conducted to evaluate the effectiveness of the compaction method and other factors, if any, in sustaining a seismic force that is greater than the assumed one and caused no damage. Based on the results of these studies, the Architectural Institute of Japan (AIJ) has indicated in its “Recommendations for Design of Ground Improvement for Building Foundations” published in 2006 that the liquefaction resistance ratio (tl/sz) of the composite ground, which consists of sand piles and surrounding compacted ground, is higher than the RL calculated by using the SPT N-values of the ground in-between the sand piles. In this paper, statistical analysis of safety factor against liquefaction, FL, was performed by using the SPT N-values of ground in Port Island and Rokko Island which were both fully reclaimed islands in Kobe city during the 1995 Hyogo-ken Nambu Earthquake (classified as intense shaking) and, together with the consideration of relative settlement, resulted in tl/sz of the composite ground being 1.5~2.5 times of tl/sz of the soil in-between piles after improvement. Furthermore, the liquefaction resistance curve of SCP-improved sites obtained from the relationship between SPT N-values and cyclic shear stress ratio during the 2011 off the Pacific Coast of Tohoku Earthquake, which was regarded as long-duration earthquake, was plotted to the left side of the curve originally proposed by Japan Road Association. Thus, the liquefaction resistance of the improved ground was found to be higher than that of the natural ground, even for the same SPT N-values, verifying the validity of the AIJ recommendation.

Jan 1, 2017