Search Documents

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

By Derrick Dasenbrock

Two DFI committees independently organized two complimentary panel sessions for the recent American Society of Civil Engineers' (ASCE) Geo- Risk 2023 "Advances in Theory and Innovation in Practice" Conference in Arlington, Virginia, July 23-26. The Geo- Institute (GI) specialty conference welcomed more than 200 professionals and students interested in risk from around the world to the Washington, D.C., area for three full days of plenary keynote lectures, papers and no-paper sessions. The GI Risk Assessment and Management Technical Committee organized the event, which is the third in a series planned on a 6-year cycle. The previous two events were in 2011 in Atlanta and 2017 in Denver.

Sep 1, 2023

By Nikolas Schmitz

For today’s construction industry, large-diameter piles are common practice, as they are more competitive than drilling a larger number of smaller piles. More and more piles are installed by drilling rigs, replacing the installation by hammer, vibrators or caisson. Equipment capabilities and technics with rotary drill rigs are highly developed, but very costly and time-consuming when it comes to rock drilling, large diameters and deep foundations. Pile top drill rigs (PBA), based on reverse circulation drilling (RCD) technology, overcome these challenges and are an efficient solution for large diameter drilling (0.6 m to 8.0 m/19.7 ft to 26.3 ft) and drilling depths of up to 500 m (1,640 ft.)in various geological conditions onshore and offshore. The paper will explain benefits of RCD technology and prove this with figures from the Mumbai Trans Harbour Link project.

Nov 1, 2022

By Gerald Verbeek, Erick Baziw

Dynamic soil analysis (DSA) in geotechnical practice is intimately related to the capability of measuring the necessary soil properties of shear modulus and absorption. In DSA the methods of analysis are based upon the stress-deformation response of soils due to imposed shear strains. Typically the soil profile is numerically modeled as linear visco-elastic system. This technique is referred to as the Equivalent Linear (EL) method, and it requires the specification of the input parameters of low-strain (<10-5) shear modulus, modulus reduction, and the equivalent viscous damping ratio, which is directly related to the soil absorption value. Downhole seismic testing (DST) has proven to be a very accurate tool for estimating low strain shear modulus values as long as source wave raypaths are taken into account, especially for near-surface investigations. DST has also been utilized to estimate low-strain interval absorption values. In these cases standard frequency domain absorption estimation algorithms (such as the spectral ratio technique) are utilized where it is assumed that the source waves are traveling along the same travel path, which is obviously not the case for near surface DST investigations. This paper outlines a unique DST absorption estimation methodology, which is carried out in the time domain and takes into account source wave travel paths. 1. INTRODUCTION There is considerable interest in methods of geotechnical in-situ engineering that provide accurate estimates of the shear wave velocity and the associated absorption values in the ground, since these parameters form the core of mathematical theorems to describe the elasticity/plasticity of soils and they are used to predict the soil response (settlement, liquefaction or failure) to imposed loads (whether from foundations, heavy equipment, earthquakes or explosions).

Jan 1, 2019

By Selvaganesh Selvaraju, Deepak Raj, Sandun N. Wimalasena

One of the world leading oil majors is carrying out a multi-billion-dollar expansion of its integrated manufacturing complex in Jurong Island, Singapore, the global oil trading and refining hub. Soil conditions at the site comprise 10-20m thick reclaimed sand, below which is 3-5m of soft marine clay underlain by stiff soils of the Jurong Formation. The conventional foundation solution would adopt driven precast concrete spun piles; however, precast spun piles have a high embodied carbon from the usage of steel and cement. In order to reduce the carbon footprint, an alternative solution comprising deep vibro techniques was developed. The EFFC-DFI carbon calculator was used to demonstrate the expected scope 1, 2 and 3 carbon emissions for both driven pile and vibro techniques. By using in-house, state-of-the-art fuel-efficient machines, alongside the innovative design concept and usage of natural materials such as sand and stones, actual CO2e emissions were reduced from a potential 21,000 tonnes, with the spun pile’s solution, to only 1,900 tonnes. The saved 20,100 tCO2e is equivalent to an average car driving 2,000x around the Earth’s equator. The paper discusses the application of soil improvement as a more sustainable, lower carbon alternative to conventional piled solutions.

May 1, 2022

By Dario Libano, Luis Carlos Tenuta, Juliano Penteado

"Subway Line Number 4 is one of the newest additions to the Rio de Janeiro subway network. Built for the 2016 Olympic Games, the 16 km (10 mi) subway line connects the south of the city, with the famous beaches Copacabana and Ipanema, to Barra da Tijuca, west of the city, where the Olympic Village and Park are located. This new line, which is estimated to cost USD 2.2 billion, is composed of six new stations: Jardim Oceanico, São Conrado, Gavea, Antero de Quintal, Jardim de Alah (JA) and Nossa Senhora da Paz Station.Brasfond participated in the construction of foundations and retaining structures for all the stations, and each presented unique challenges. This is not surprising considering the difficulties present in a highly-dense urban environment including utilities, nearby buildings, traffic limitations and noise.Of all the stations, JA Station was the most challenging to construct. It was located in the middle of an avenue between residential high rises supported on shallow foundations as well as below sea level in sands with high groundwater. The other five stations were located in small parks and squares, with no buildings in the immediate proximity.The interaction between designer, owner, and the general and foundation contractors during execution was key in safely reducing the construction schedule. This was significant given the unforeseen construction delays the client, Linha 4 Sul JV, faced due to permitting, utility and traffic relocation so that the owner could fulfill their final goal: making the line operational by the Olympic Games. The GeologyGeologically, the state of Rio de Janeiro is formed by Pre- Cambrian crystalline basement rock. Its geological formation is very old and comprises two major orogenic cycles, a Mid-Precambrian formation, called “Transamazonian” (Proterozoic Era), and an Upper-Precambrian to Cambrian called “Brasiliano” (Proterozoic-Paleozoic). The soil structure of the city of Rio de Janeiro is represented by a core of crystalline rocks, usually granite-gneiss, covered with a layer of residual soil and/or partially weathered rock.JA Station is located in a Rio de Janeiro neighborhood called Ipanema, between the Atlantic Ocean and Lagoon Rodrigo de Freitas. Local geology is composed of a superficial soil, consisting of medium to coarse grained sands. Top of rock varied significantly from 20 m (66 ft) deep on one side of the station to 33 m (108 ft) on the other. Water is at a depth of 3 m (10 ft)."

Jan 1, 2016

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By David H. Sanders, Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Large-diameter drilled shafts (DS) are a critical part of a seismic-resistant system, and therefore it is important to be able to accurately model lateral resistance. To undertake the lateral load analysis of largediameter DS, a finite-difference p-y analysis program, NVShaft, is being developed at the University of Nevada Reno. Validation of the new program involved numerous p-y analyses using commercially available programs. Subsequent comparisons suggested the program's ability to yield reasonable predictions for typical diameter DS. Based on the I-15/US 95 load test program carried out in Las Vegas, NV, this study presents the evaluation of NVShaft in Nevada’s subsurface condition. Lateral load analyses of a 2 ft and an 8 ft diameter DS were attempted using NVShaft. The location of the applied lateral loads and the presence of cemented soil-layers were incorporated in the modeling. A good agreement between NVShaft prediction and the measured response was found for the 2 ft diameter DS. For the 8 ft diameter DS, a stiffer response was predicted. The inspections of the moment-curvature characteristics at different load levels suggested cracked response of the concrete due to prior axial load testing may be one of the reasons behind the deviation.

By Alexander Filotti, Richard Kalson

"In the last decade, the construction industry has witnessed significant changes in the project delivery systems and contractual relationships between the general contractors (GC) and Deep Foundation Specialty Contractors. The Deep Foundation industry, especially including industry specialty subcontractors, have experienced a significant increase in requests that project risks be transferred through contract documents to subcontractors and suppliers with a decrease in margins for the industry. GCs regularly revise their form subcontracts to take into account recent experiences/contractual trends and newly issued judicial precedent, an exercise that is less frequently undertaken by subcontractors and suppliers. These contradictory trends are at the base of the ethical analysis of subcontracts that comprises the subject matter of this paper. Using contracts as a risk management tool in order to mitigate the general contractor’s risks in the context of dynamic changes in the legislative environment will also be addressed. Furthermore, another possibility for risk mitigation for the industry is to actively promote the introduction of the latest technical developments into the contract documents.CONTRACTS’ ETHICSFor thousands of years, ethics have been a constant presence in our lives and have been debated by different branches of philosophy. In modern times, ethics in business started to be an imperative for the success of a globalized economy.“Ethics are standards by which one should act based on values. Values are code beliefs such as duty, honor, and integrity that motivate attitudes and actions.” (Rumbaugh 2004). Some of these values and actions have been carved in legislation in general and in business legislation in particular. More and more, unethical business practices (e.g., corruption) are identified as the root cause of poverty, underdevelopment, and war around the world. In the context of contract ethics, three aspects are of interest:•,Ethics of contract construction•,Ethics of contracting processes•,Ethics of risk allocation in contracts"

Jan 1, 2016

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

Jan 1, 1990

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By Antonio Marinucci, Robin Mao

The new Hangzhou West Railway Station, which is currently in the early stages of construction, will be located in the city of Hangzhou, China. To accomplish the ambitious goals of the project, the construction work and station building was divided into three project areas. The original design utilizes 1,580 drilled shafts with diameters of either 800 mm or 1000 mm (32 or 40 inch) to support the new Station and its various ancillary structures. The drilled shafts will be tipped into the moderately weathered argillaceous siltstone a distance between 5 and 15 m (16.5 and 49 ft), resulting in an effective pile length ranging from 35 to 43 m (115 to 141 ft), respectively. For the first phase, approximately 550 production drilled shafts will be installed. Eight (8) sacrificial drilled shafts each with a diameter of 1000 mm (40 inch) were installed to a depth ranging from 50 to 57 m (164 to 187 ft), and were tested to confirm the design parameters used for the first phase, to evaluate the contractor’s installation means-and-methods, and to provide guidance whether redesign is warranted for the subsequent two phases. Bi-directional static load testing was performed using a donut-shaped Super Cell to apply unidirectional axial loads up to 13,200 kN (2,970 kip). This paper will describe the bi-directional testing and select results obtained therefrom. The axial compressive and uplift resistances determined from the testing verified that the available axial resistance of a single drilled shaft exceeded the minimum design requirements.

By José Carlos do Amaral, Marcelo Groszownik, Jorge Beim

"Initiated in 2008, the project of this 1800 km long Electrical Transmission Line is a job of extreme technical complexity, crossing regions of major forests and rivers. When ready, it will allow the large Brazilian states of Amazonas, Amapá and Pará to use the energy from hydroelectric plants, thus eliminating the need for the use of diesel fuel thermal plants, with their much larger environmental footprint. Due to its extraordinary characteristics, the Green Peace and the Discovery Channel constantly visited the job. The part between the Amazon and the Xingu rivers started in 2012, and encompassed about 100 transmission towers with up to 150 m height, through a region known as “Alagados”. This region exhibits a 1.5 m water level during the rainy season, and soaked ground the rest of the year. Navigation of regular vessels is impossible during the flood season, when a dense vegetation called “bulhado” fills the riverbed, and vehicle traffic is impossible during the dry season, due to the extremely low surface soil resistance. Great logistical and technical difficulties were encountered for driving and determining the capacity of the piles. New systems had to be developed for driving the piles, with the simultaneous use of 15 small piling rigs. The final penetration, total number of hammer blows during driving, plus Dynamic and Static Load Tests were used for determining the driving and acceptance criteria.The geographical challenge and initial conditionsThis paper describes the execution of foundations for a 500 kV Electrical Transmission Line in a region that becomes flooded during the rainy season and heavily muddy during the dry season. This is the monsoon climate, typical of the equatorial region of Brazil, where there is a rainy season lasting for about half the year, followed by a very dry season. The temperature varies very little throughout the year, due to the proximity to the equator. The locals call the rainy season “winter” and the dry season “summer”.The most important part of the so-called “Alagados” region is situated inside an Environmental Extractive Reserve (RESEX) called “Verde para Sempre” (Forever Green), created in 2003. This is one of the largest environmental reserves in Brazil. It is an area controlled by the Brazilian Environmental Control Department, the Chico Mendes Institute (ICMBio). The environment control parameters are very strict.No deep foundation had ever been executed before along the “Alagados” region. The main challenge faced on this job, however, was working in a place where self-propelling vessels or land vehicles and equipment cannot be used. During the rainy season there is a dense and intricate vegetation called “bulhado”, which prevents the movement of outboard motor boats with propellers going deeper than 50 cm. In the dry season, the heavy mud prevents the movement of foundation equipment, excavators, trucks and other machinery."

Jan 1, 2015

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010