Search Documents

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By W. H. Craig

Techniques have been developed for installing model piles into beds of soil under high sustained acceleration levels aboard a centrifuge. These piles have been subjected to static and/or cyclic lateral loading in order to assess their performance and provide a data base for assessment of various design techniques for laterally-loaded single piles. From measured bending moment profiles the so-called 'p-y' curves have been deduced using fifth order splines for curve fitting, followed by subsequent differentiation and integration. The results show some divergence from the predictions of the semi-empirical designs, but these latter are generally found to be acceptable.

Jan 1, 2010

By Z. C. Chen

Based on the analysis of load test data of long floating piles in soft soil regions, the expressions of load-transfer function of pile shaft and tip for soft soils are presented in this paper, and the data of cone penetration test are suggested to use for calculating the parameters of load-transfer functions. For the loads of pile within the range of the working load of pile, the estimated pile stiffness by the suggested method in this paper are in satisfactory agreement with the results of load tests. The current Vijayvergiya's method and Satowa's method also are used to calculate pile stiffness in soft soil for comparison.

Jan 1, 2010

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By P. Davies

The Hillside Smelter presently under construction at Richards Bay, Republic of South Africa, will be, on completion, the fifth largest aluminium smelter in the world. The site selected for this plant is underlain by sandy soils of variable density to depths of 30m or greater. In order to firmly establish pile founding depths required for alternative pile types in the variable subsurface conditions prevailing across the site, a pre-construction test piling programme was conducted incorporating piles instrumented with resistance strain gauges. The results allowed analysis of the relative contributions of end-bearing and shaft friction to the overall bearing capacity of each pile type and permitted comparison with the predictions of conventional static bearing capacity analyses. Conformance with acceptance criteria in respect of allowable pile head movements for single piles was also examined.

Jan 1, 1996

By Willie M. NeSmith

The use of drilled (screwed) displacement piles is an emerging sector of the United States deep foundation industry. During installation of these systems, a Ko to Kp environment is created in the materials surrounding the pile immediately prior to casting, and this condition results in increased shaft and toe resistance in soils where displacement leads to densification. Current continuous flight auger and drilled shaft design methodologies in the United States assume a Ko to Ka condition in the vicinity of the pile, and are thus an inappropriate starting point for static capacity analysis of drilled displacement piles. This paper examines constructability issues, and the sensitivity of performance to installation, and offers an empirical design methodology for drilled displacement piles. The proposed design process has been based on evaluation of 40 load tests, primarily in granular materials, and in a variety of geologic settings, and includes modification for soil types within the coarse-grained range.

Jan 1, 2002

By K. Fujita

In order to deal properly with the fundamental aspects of pile construction, the following problems and their solutions are introduced: For driven piles - stresses, damage, movements of surroundings, compaction of ground, deviation of pile direction and location, selection of pile hammers and penetrability of piles are important factors. For drilled piles -loosening of the ground, supports for boreholes, minimizing ground loosening and defects are critical items. Attention should be given to changing soil characteristics. Also, supervision by experienced engineers and good workmanship by skilled laborers are recommended to ensure the quality of the piles.

Jan 1, 2010

By Serge Borel

An efficient design method is proposed for "piled-footing" and "piled-raft" foundation under lateral loads. It combines the methods used for the displacement design of shallow and deep foundations and takes into account the interactions between the piles and the cap or raft. This method has been applied to previous full-scale tests carried out in the United States. Two groups of six instrumented driven piles were laterally loaded several times: first with the concrete pile cap in direct contact with the soil, and then, after a thin layer of soil had been removed beneath the cap. The proposed method models well the real behavior of piled-raft foundations. It highlights the positive effect of the cap in contact with the soil, which reduces significantly the displacements and the maximum pile bending moments. These are divided by two for the analyzed case histories.

Jan 1, 2002

By Martina Balic

Dynamic properties of the drilled shaft foundations supporting Doremus Avenue Bridge were determined by forced vibration testing. The main objectives of the substructure testing at Doremus Avenue Bridge were: (1) site evaluation with respect to the dynamic soil properties, and, (2) shaft evaluation for the purpose of definition of their dynamic stiffness. The site characterization entailed crosshole testing for the purpose of evaluation of the shear modulus profile. The drilled shaft impedance evaluation was done through forced excitation using an electromagnetic shaker. The responses of the tested shaft, as well as the response of adjacent shafts, were measured for the purpose of evaluation of the shaft interaction. To gain a better insight into the shaft dynamics, one of the shafts was instrumented with five triaxial geophones distributed along the full length of the shaft. The scope and results of the site characterization, shaft impedance and shaft interaction evaluation are presented.

Jan 1, 2004

By Gary M. Weinstein

Micropiles have seen increasing use for foundation support and slope stabilization applications over the past half century. Most often designed and installed in groups of vertical or battered elements or combinations thereof, continued applied research conducted through partnerships established between academia, government and industry has led to the recent development of practical engineering and design guidelines for such micropile systems. In contrast to a group of directly loaded micropiles, the micropile network relies on a three-dimensional array of reticulated elements to encompass and internally reinforce the soil, resulting in a network or "knot" effect. The potential for enhanced engineering behaviour of reticulated micropile network systems compared to that of a group of micropiles has been continually revealed by numerous researchers in the past. The concept is elementary - the roots of a tree interact with the soil to form a composite foundation capable of performance superior to that of the individual parts. However, given the large number of parameters which must be modelled and studied, experimental assessment and rational analysis of the soil-structure system has been difficult and therefore, in contrast to above, reliable design methods have not yet been forthcoming.

Jan 1, 2003

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By John R. Davie

This paper describes the design and construction of two 5.6 MN capacity drilled piers installed to support the main loading elements of a large cantilevered gantry crane. The critical crane columns were located within and at the edge of an existing sheet-pile cofferdam, which had been filled with loose coal slag when it was originally constructed Due to the presence of the slag and the age and questionable condition of the sheet-piles, the drilled piers were installed to provide vertical and lateral supports for these columns. The lateral capacity of the piers was supplemented by two smaller drilled piers and two large spread footings that were linked by a system of grade beams.

Jan 1, 2006

By M. Y. Xia

In this paper, based on the Theological tests of the interface between clay and concrete, an interface Theological model is proposed and is used in the finite element analysis which takes soil as viscoelastic mass and Theological effect of the interface between diaphram wall and ground into consideration. Its results are compared with those without an interface element, without considering the relative creep displacement. Close attention is paid to the variation of wall with time under the condition of various interface shear stiffness and viscous sliding coefficient, and their effects on the wall bending moment are primarily verified in the paper. The change of wall bending moment with time, trench heave and wall displacement in different excavation depth, bracing position, parameters for soil are also studied.

Jan 1, 2010

By James D. Hussin

The Florida limestone is a relatively soft rock which presents many challenges to engineers when designing deep foundations. One alternative is micropiles which have grown significantly from their early days as very small diameter, light capacity elements. Also known as minipiles, pin piles, needle piles or root piles, micropiles offer an attractive deep foundation alternative for sites with tight access, low headroom, and where difficult subsurface conditions or obstructions necessitate a small diameter, high capacity deep foundation. The ability to confirm the competence of the limestone bearing formation by drilling in a rock socket has made micropiles a growing deep foundation selection in Florida.

Jan 1, 2003

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002