Search Documents

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind's eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929

By K. Tada

A surface of a magnesium slab (hereinafter, referred to as Mg slab) or magnesium alloy slab (hereinafter, referred to as Mg alloy slab) becomes black with the use of conventional manufacturing methods. The methods also involve a danger that an explosion of the molten magnesium occurs through contact with cooling water. Thus, it has been impossible to produce a slab having a smooth surface. In the present method, a molten magnesium alloy is supplied into a mold, which is sheltered from the surroundings, from a pool in tundish, which is shielded from the surroundings. AZ31B slab formed in the mold is drawn horizontally out to the outside from an outlet of the mold by revolving of the pinch rolls. A cooling water is jetted at an acute angle onto the slab on the outer side of the mold outlet. Further, an inert gas is sprayed at the inner side of the mold outlet in order to seal in a gap between a free surface of the molten magnesium alloy and a sheltered board surrounding an upper surface of the mold. As a result, oxygen and droplets of the cooling water are prevented from running back to the mold side through the gap. AZ31B slab has a smooth surface condition and high quality without a gas porosity, a segregation or the like. Further, the slab has a size of a width of 100 to 120 mm, a thickness of 5 to 20 mm and a span of 10 m or more.

Jan 1, 2006

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By A. Zarei-Hanzaki, O. Golmahalleh, S. M. H. Hosseini, H. Azizi-Alizamini

The main importance of acicular ferrite microstructures arises from their desired combination of mechanical properties in comparison with the bainite and ferrite-pearlite microstructures. Several factors affect the microstructural transition from bainite microstructure into the acicular ferrite one. As is well established any factor corrupting the prior austenitc grain boundaries nucleation potential, such as the thin layer of allotriomorph ferrite and the austenitc deformation inhomogenities may promote the acicular ferrite formation instead of bainite. Accordingly, this study deals with the effects of the aforementioned features on the acicular ferrite formation in low carbon microalloyed steel. The results indicate that the formation of strain-induced ferrite at the prior austenite grain boundaries accompanied by deformation inhomogenities in the austenite grains change the effectiveness of allotriomorph ferrite on acicular ferrite formation from active to inert one.

Jan 1, 2004

By J. L. Bowlby

TWO years ago, at the annual meeting of this Society, the writer presented a paper dealing with various aspects of the water problems existing in the Cape Breton coal-mining area. Much of that paper was of a theoretical nature, in that an attempt was made to get at the fundamental principles underlying the problems, in order to establish a sort of background against which future results could be laid. Up to that time, only Central power plant in Glace Bay had been under observation, and, since the work had been in progress only a year, it was recognized that there were strong possibilities that certain variations in procedure might have to be introduced as w; became better acquainted with our problem. We were by no means certain that we had covered all the facts of the case. The present paper will therefore be of the nature of a progress report, rather than a formal contribution to the Society. Subjects of a theoretical or academic nature will be avoided as far as possible, attention being confined chiefly to the results obtained during the past two years. In looking over the work with low-pressure boilers, there are certain general conclusions that can apparently be safely drawn. Wherever possible, proper operating conditions will be expressed in terms of appropriate units. Absence of corrosion in boilers where the alkalinity has been maintained within the pH range 11.0 to 11.4 forces one to the conclusion that these are safe working limits. Previous experience had shown that corrosion would occur if the alkalinity were much reduced. Higher alkalinities are un-necessary, more expensive, and are said to introduce the possibility of pitting. We made no attempt to obtain quantitative data in respect to pitting. It is said to occur at pH 12.0. Consequently, conditions of alkalinity were main-tained well below this figure. In the above paragraph, the pH range 11.0 to 11.4 applies to boiler waters which have received the lime and soda treatment. The general practice, when this treatment is employed, is to use 1.0 lb. lime to 7.0 lb. washing soda. At Central power plant, soda-ash is at present substituted for washing soda, the equivalent proportions being kept the same. But not all the plants are on the lime and soda treatment. At Waterford Lake, a 1: 1 mixture of soda-ash and trisodium phosphate is satisfactorily employed, and in Sydney Mines and at No. 3 power plant in Sydney, good results are being obtained at a somewhat greater cost with a commercial phosphate treatment.

Jan 1, 1936

By C. A. Lorenson

THE Marmoraton mine is located a mile southeast of Marmora, a village in Hastings county, Ontario, 130 miles east from Toronto and 143 miles west of Ottawa. Highway No. 14 from Belleville intersects Highway No. 7 at Marmora and the branch line of the Canadian National railway between Trenton and Bancroft passes through the property just east of the open pit. HISTORY AND GEOLOGY The Marmora orebody appears as the whorls of a thumb print on the aeromagnetic survey map released by the Ontario Department of Min.es early in 1950, the survey of the district having been made in 1948 and 1949, under the joint auspices of the Department of Mines and the Geological Survey of Canada. The 'anomaly' appeared to have interesting possibilities, so Bethlehem representatives carried out a ground survey and began drilling the property in June, 1950. A total of 40 holes, aggregating 37,000 feet, were drilled to delineate the ore-body. The Marmora orebody is a re-placement of Precambrian limesto.ne with zones or bands of magnetite interlaid with metamorpl1ic rocks and cut by later intrusives. The ore and associated Precambrian rocks are overlain by 100 to 150 feet of flat-lying Palaeozoic limestone. It is a low-grade deposit averaging 33 per cent iron and requires concentration to raise it to 65 per cent iron grade.

Jan 1, 1958

By Irvine J. Berscheid

This paper describes a rock drill bit which, although conventional in the processes of manufacture and use on the job, has incorporated into the outer wall or periphery of the insert, where wear is always the greatest, a variable amount of extra metal, distributed in units of height of insert to withstand this excessive wear. Explained are variations of construction, how the extra metal enables the bit to drill more footage, prevent antitaper and the need to gauge grind, increase penetration rate and the length of run per regrind, reduce shank breakage and ma-chine costs, and permit increased production per man-shift, without requiring any change in equipment already on the job. F OR purposes of clarity, reference to bits here means integral rods or multi-winged bits which have their inserts sharpened to a conventional shape. When dull, the insert has worn, on its face, a flat which increases in width as we progress from near the center of the bit toward the outer edge. Very

Jan 1, 1965

By D. Sbarbaro

In many modem concentrators the use of supervisory systems in their grinding circuits has meant more consistent operations and increases in capacity. These systems rely on a series of specific algorithms that uses different pieces of information and drives actions over the process. One of these algorithms is the ball mill overload detection, which plays an important role in any supervisory strategy designed to maximize ore feed rate in wet grinding circuits. This paper introduces different overload detection algorithms, and compares them in terms of the time taken to detect the overload condition. This comparative analysis is based on highly noisy power draw measurements obtained in an industrial plant.

Jan 1, 2007

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By W. F. James

"The property of Siscoe Gold Mines, Limited, comprises about 1,600 acres, including Siscoe island and adjacent claims under water in Montigny lake, in Dubuisson and Vassan townships, Quebec.For many years the property was reached by way of Harricana river and its chain of lakes from Amos, Quebec, about 45 miles distant. In later years a highway has been built from Noranda east through Val d'Or, about 5 miles distant.Gold was discovered on one of the claims on the north shore of Montigny lake as early as 1911, but these gold discoveries have never been economically important. Several years later gold was discovered on Siscoe island and considerable surface work was carried out. Still later, iscoe Gold Mines, Limited, was formed and carried out further work, some of it through shallow shafts. In 1928, larger scale operations were undertaken and a 100-ton mill was constructed. In the years following, production· was on a larger scale with lower grade, until finally a milling rate of over 1,000 tons a day was attained. Approximately 1,500,000 tons were treated between the end of 1940 and mid-year 1945. At present the milling rate is down to about 200 tons a day and work is confined chiefly to some of the less important veins that have been recently developed.The following is a summary of production up to December 31st, 1946:"

Jan 1, 1954

By Mahmoud Shakeri1

Various types of thin-walled structures have been frequently used as energy absorbers to mitigate the adverse effects of impact and hence protect the vehicle structure under consideration when subjected to different loading conditions. Compression tubular structures that buckle in a progressive manner, can be used to advantage, providing inexpensive and versatile, but nevertheless weight and stroke efficient energy absorbers. In this paper quasi-static nonlinear finite element simulations are performed to study the effects of number of corners of the cross-section, wall thickness, plastic hardening rate of material, foam-filler and load angle on deformation mode and mean crushing force of tube. Crush strength increases as the number of corners of the cross-section increases, though it almost saturates for the number of corners beyond 11. Higher plastic hardening rate stabilizes the collapse pattern. Foam-filled tubes seem to have higher critical load angles in oblique loading and display a more stable and gradual decrease in mean load over the transition region. Substantial decrease in the initial peak load and dynamic load at any a given deflection was observed as the load angle increases. The investigation of bitubal arrangements and Multi-cell tubes reveals that these may be preferable to monotubal specimens due to the presence of the inner profiles. In addition, a comparison is conducted between the numerical and experimental results of the mean forces of some special angle elements. Good agreement is obtained.

Oct 1, 2011

By J. B. De Hart

In the September issue of the Bulletin, 1923, there is a paper by J. A. H. Church on "The Spontaneous Combustion of Coal in Mines", which is more or less a general discussion of the subject. Mr. Church gives a list of mine fires which have occurred in Alberta. Of the total of thirteen fires, six are attributed to spontaneous combustion. Of these six fires, it will be noted that five are in thick pitching seams. These fires occurred in the following mines during the years shown, at Frank in 1909; at Lovett in 1916; at Cadomin in 1920; at Yellowhead in 1922, and at Cadomin in 1923. Every one of these fires has occurred, as Mr. Church points out, in a seam of over 12 feet in thickness, and furthermore not one of these fires has been extinguished, although in every case large sums of money were expended and considerable risks . taken in fire fighting. Now it is quite evident from these facts that mines working seams of this nature are faced with a very grave danger and it behooves us to study the matter and endeavor to arrive at some practical method of preventing the loss of our coal mines from this cause.

Jan 1, 1924

By M. K. Senicie

IN July, 1937, Asbestos Corporation, Limited, installed an automatic conveyor-belt scale at their King mine, Thetford Mines. The equipment was purchased 'on trial' and its performance has proved entirely satisfactory to the staff. The scale was manufactured by the Toledo Scale Company, of Toledo (Ohio) and Windsor (Ont.) and was installed by one of the Scale Company's engineers. The electrical recording equipment was installed by Keith Mercer, Reg'd, of Montreal, Canadian agents for the manufacturers, the Builders Iron Foundry, of Providence, Rhode Island. The recording equipment consists of a duplex weight-transmitter attached to the scale-head, a duplex totalizer with differential relays, a belt-speed compensator, a rate-of-delivery recorder, and a rate-of-delivery indicator. As it was desired to run the mill at maximum capacity, it was necessary to know the rate of feed at all times, so that any lessening of rate of feed or delays would be recorded and could be corrected. After having determined the rate of feed to the mill (100 per cent capacity), it was required to have weighing and recording instruments which would show: (1) The rate of feed per hour. (2) Any variations .in the load. (3) Any delays and the duration and time of the delays. Rate of tonnage recorders in the mill superintendent's office and at the point of feedi.ng were necessary, as was automatic control between the mill superintendent and the feed man. It was desired to have a permanent record of total tonnage fed per shift or day; weighing and recording mechanism had to have sensitivity to record all previously mentioned conditions. Mechanism had to be of rugged construction, and be so built that it would stay in good operating condition, with the minimum amount of adjustment and supervision.

Jan 1, 1938

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By A P. Powell

This paper deals with the power plant at Cassiar Asbestos Corporation Ltd., Cassiar, B.C. It discusses the units installed in the plant, the distribution of power and the costs involved. The efficiencies and economics of this power plant are considered to be somewhat better than average. Introduction C ASSIAR Asbestos Corporation's power plant had its inception in 1952 with a 15-by 15-ft. log cabin containing two International Harvester diesel generator sets of 50 kw. total generating capacity. Over the years, it has grown to its present size -an 80 by 82 ft. by 35-ft.-high rigid-frame Butler building housing eight 2,300-volt diesel generating sets, a 2,300-volt distributing switchboard, a 550-volt auxiliary panel, three air compressors, six heat exchangers and other related equipment. The units in the power plant, numbered according to their order of placement, are rated as shown in Table I. The total generating capacity of the plant is 3,673 kw. All of the generators are of the open vertical design except that on No. 7 engine,

Jan 1, 1965

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By A. B. Luz, A. Middea

Kaolin clay is heavily used in the paper industry as a coating and a filler, however to attend the specifications required by the industry it has to be processed. Kaolin is also used as a filler and pigment in various materials, such as paint, plastic, rubber etc. Some crude kaolins as mined in Northern Brazil, contain colored impurities such as iron oxide and rutile/anatase. These minerals normally are stained by iron and as a result vary from yellow to dark brown in color. The kaolin beneficiation process used in that region consists mainly of degritting, fractionation by centrifuge, high gradient magnetic separation, bleaching with sodium dithionite, filtering and drying. In some kaolin clays from that region, titanium oxide mineral occurs in fine fraction, lower than 2 µm, and so making the industrial process more difficult. The conventional method of classification and bleaching with sodium dithionite, markedly improves kaolin brightness, but has little effect on anatase removal. In fact, the fine fractions resulting from centrifugation, in many cases contain more TiO2 minerals than the original whole clay or the coarse fraction. The present work is related to purification of Brasilian kaolin clay using selective flocculation for removing its colored impurities such as rutile and anatase. This study was conducted in bench scale and it consisted of: blunging, screening, conditioning and decantation. Overflow and underflow resulting from settling of the flocculated material were then dried and submitted to TiO2 and brightness analyses. Sodium polyacrylate and sodium silicate were added to kaolin clay suspension as dispersant and ammonium hydroxide was also added to adjust pH. After degritting, the minus 44 µm fraction was conditioned with hydroxamate surfactant and then polymers of different anionic charge were added. The influence of pH and type of polymer on efficiency of TiO2 removal, as well as kaolin mass recovery were studied. The results obtained in the present study are quite promising. It was possible to diminish TiO2 content and increase kaolin brightness (ISO) from 82 to 88%.

Jan 1, 2004