Search Documents

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By P. Maltby

"Smelter Feed Preparation Falconbridge Nickel Mines Limited, Sudbury Operations, operate 4 mills and a smelter to produce Bessemer Ni-Cu matte for refining in Norway. Approximately 1400 tons of Ni-Cu concentrate are produced daily which are dried from a filter cake containing 14% moisture to 7.5% moisture pellets. Concentrate drying is done by 4 rotary dryers as shown in the 'Dryer Performance Data' at four separate locations. The dryers all form part of the feed preparation stage prior to sintering.The rate at which concentrate can be produced through the Sinter Plant largely depends on the quality of the dried product which makes up the feed. A feed consisting of mostly hardened pellets will sinter much faster than a feed which consists of broken pellets and dust. Dryer products require:1. Good green strength to survive shipment and handling.2. Correct moisture content.3. Sizing within a range ideally from 1/4"" to 10 mesh in diameter.Dryer performance data is shown in Table 1. Capital costs between the two types of dryers are comparable with the Roto-Louvre producing generally a larger better-formed pellet. Dryer feeds differ in that at both Hardy and Fecunis, Ni-Cu concentrate filter cake is the only feed while at the Falconbridge slurry plant the dryer feed can consist of up to 10% by weight of smelter flue dust resulting in a combined concentrate-dust pellet for feeding to the Sinter Plant. To the Falconbridge Sinter Plant dryer, dust and limestone are added for the smelting process in addition to Ni-Cu concentrate."

Jan 1, 1972

By T. Maruyama

Tamano Refinery started its operation in 1972 with the cathode production capacity of 84,000 tons per year. After several expansions, the production capacity increased to 228,000 tons per year in 2001. In this paper, we are introducing our next expansion projects starting October 2006. The project expands the production capacity of cathode from 228,000 tons to 260,000 tons per year. The main modification of this project is the conversion to the ISA process and the installation of additional seventy-two cells in the No.2 Tankhouse. The No.1 Tankhouse remains the same, using the conventional process. Half of our starting sheet cells are converted to commercial cells. The other expansions are to enlarge our purification plant. And the incidental facilities are enlarged, for example, circulation tanks, heat exchangers, filtration system, etc. Finally, this paper describes those improvements to our refinery performance and preparing for future expansions.

Jan 1, 2007

By J. Schmidt

Cold drawing of copper wire rod is usually combined with an in-line annealing process to adjust the ductile microstructure of the wire again. One important key factor for successful annealing is the quality of the copper itself. Rod producers can check the recrystallization behaviour of the rod by different methods: chemical analysis, Spiral Elongation Test (SEN) as well as the Rapid Elongation Test (AR) are some examples of common testing methods. The comparison of the results of these methods does not always show sufficient correlations. The paper introduces firstly the SEN and AR-Tests and their different approaches to the mentioned task. The second step is to compare some results of the SEN-Test with the results of the AR-Test and identify causes of deviations. Thirdly, the effect of pre-annealing is discussed, which is especially common for wire rod with diameters of more than 8 mm.

Jan 1, 2007

By M. Huang

Electrodeless conductivity was employed to investigate the feasibility of continuous on-line monitoring of the free acidity of sulphate and/or chloride solutions of Cu and other base metals from various hydrometallurgical processes. These solutions were measured with both commercial and experimental electrodeless conductivity sensors from 15 to 250°C. It was confirmed that hydrogen ion has the greatest impact on conductivity by carrying the bulk of the current because it is the most mobile ion. In combination with a solution speciation analysis the conductivity sensor can be calibrated to account for the contribution of Cu electrolytes as well other dissolved salts allowing fast and accurate on-line measurement of free acid. The sensor was tested at both lab and pilot scale with very good performance. The average difference between the measured and the titrated acid concentration was less than 5%, which is excellent for industrial applications.

Jan 1, 2007

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By R. D. Livingstone

"THE LETHBRIDGE COAL FIELD lies mainly .to the north and west of the city of Lethbridge. Mining carried on in this area for over eighty years until 1965. Before the building of a railway the coal was carried by bullock wagon to Montana for use in smelting, and for a while by river boat to Medicine Hat for railway use. The single, almost flat, worked seam is designated the ""Galt"" seam and is about 1.5 metres thick. It belongs to the Belly River formation and is under cover of 80 to 180 metres of weakly stratified sediments. A complex system of cross faults adds to the mining difficulties. Close timbering required in the entries and rooms reflected in a high timber cost and lower output per man shift. The coal is High Volatile"" C"" bituminous in rank with maximum gross calorific value of 11,200 Btu per pound and with a well defined cleavage. Roof conditions in the field range from very tender and very heavy on the south end of the field and west of the Oldman River to a more stable character to the north. Relatively speaking, the whole field would earn a rather tender rating and definitely so in relation to many U.S. fields. Floor conditions are characterized by a bentonitic type heaving in the south end of the field west of the Oldman river to a more stable situation in the north, which can tolerate shuttle car operation if kept drained. Water problems are minimal, except paralleling the Oldman River, where the seam dips below the river level. While vigilance is necessary to prevent accumulations of gas, the volume is rather limited. The seam was entered by shafts, except where small mines were located along the Oldman river banks and gained access by drifts. The coal seam was developed by driving either 3 or 4 Face entries 2 1/2 metres (8 ft) wide on 18-metre ( 60-ft) centres. Sets of dual butt entries driven at right angles to the Face entries completed development work. Normally rooms up to 8 metres wide were turned off the butt entries on up to 11 - metre centres. These were worked in groups of three to five, depending on the roof conditions, and normally advanced 60 m (200 ft). In some areas rooms had to be abandoned short of their objectives due to roof pressure, heaving floor and intermittent work."

Jan 1, 1985

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By S McQuitty

The metallurgical treatment of Falconbridge ore re-quires an extremely fine grind of the pyrrhotite portion ? for maximum liberation and recovery of nickel. This paper describes the operation of a grate discharge pebble mill in closed circuit with cyclones regrinding 25 to 30 tons per hour of sulphides to approximately 90 per cent minus 325 mesh. The consumption of the screened ore grinding medium is of the order of 2.5 pounds per kw.-hour, or less than 1 per cent of the tonnage of re-ground sulphides. IN RECENT years, there has been a considerable interest in pebble grinding in the uranium industry, and a number of installations have appeared. However, the use of sulphide ore pebbles as a grinding medium has so far been relatively limited. There has also been some question as to their suitability for the very fine grinding of sulphide concentrates. This paper describes the preliminary results of a commercial operation involving the

Jan 1, 1964

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

By Hani Henein

Most metals and alloys processed undergo a solidification processing step. Increasingly, there is a growing number of solidification processing routes that involve rapid solidification of the alloy. These include strip casting, high pressure die casting, 3D printing, and atomization for the production of powders or spray formed parts. By contrast, there are few experimental techniques developed to study the solidification path of alloys during rapid solidification. Amongst these laser melting and solidification, Electromagnetic Levitation (EML) and Impulse Atomization (IA) are the most prominent. Of relevance is the formulation of the solidification path of an alloy and the resultant identification and quantification of metastable phases and their relationship to processing conditions. This typically involves the understanding of the interplay between undercooling and cooling rate for the various phases that form. This presentation will outline some of the methodologies developed to quantify phase fractions and their solidification path as a function of processing conditions using EML and IA.

Jan 1, 2016

By J. E. Nesset

The past 50 years have been a golden era, not just for the CMP but also for the development and success of Canadian technologies in the field of mineral processing. The CMP has played a critical role of technology transfer agent, and the success of these technologies is also linked to the success of the CMP itself. The presentation will cover, in brief, the growth of the CMP from its origins as the Canadian Gold Metallurgists in 1964, with some 39 attendees, to the present day when the annual meeting sees 500 and more from a dozen countries. Also covered will be selected technology success stories from the 50th anniversary volume to be given to all delegates ‘Canadian Contributions to Mineral Processing Technology 1968-2018’. The volume itself highlights some 40 technologies that have been divided into five categories; process water treatment and minesite environment, technology innovations, innovations in operations, technology providers and university contributions. Some international perspectives will also be shared.

Jan 1, 2018

By Louise Grondin

Laronde Mine has been working for a number of years to identify substances that could contribute to process water toxicity and to find an effective way of removing these contaminants from the water. Initial studies have identified ammonia, nitrite, cyanide, thiocyanate, cyanate, dissolved organic carbon, copper and zinc as potential toxicants. Bench-scale tests were carried out with Lakefield Research to find a water treatment process that could effectively remove the suspected toxicants. Nine treatment processes were evaluated: 1) granular activated carbon (GAC) filtration followed by zeolite, 2) zeolite filtration followed by GAC filtration, 3) aeration followed by GAC filtration, 4) multi-stage GAC filtration, 5) chlorination followed by dechlorination, 6) addition of clay based polymer, 7) treatment with peroxide and ultra-violet light, 8) bulk addition of GAC and zeolite powder, 9) treatment with bacteria. This article presents a summary of the test results and of the problems associated with the evaluation of technologies for the treatment of toxicity.

Nov 1, 2002

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By R. A. L. Drew, J. P. Immarigeon, F. Jalilian, M. Jahazi

In the present work TLP bonding of Inconel 617 is investigated. The influence of the main processing parameters i.e. time and thickness of the interlayer were studied with optical and scanning electron microscopy. Boron containing interlayers with two different thicknesses were used and the influence of various holding times from 5 min to 24 hours on the microstructure of the bond region was investigated. The results indicated that, for the testing temperature of 1065°C and holding times above 2 hours with an interlayer of 25.4 microns thick no liquid phase was observed. The same phenomenon occurred only after 6 hours for a 76.2 microns thick interlayer. Precipitate growth started at grain boundaries and continued inside the grains. The composition, size and morphology of the precipitates were studied using electron microprobe analysis. No noticeable changes were observed in the grain size of the base metal with increasing holding times.

Jan 1, 2004

By W. Beres, Li. J.

The finite element method (FEM) has been applied to investigate the stress fields and deformation of a TiN/Ti-6A1-4V coating/substrate system subjected to nanoindentation. MSC Patran and MSC Marc were used to prepare the three-dimensional finite element models and to perform the simulations of the Vickers nanoindentation experiments. Pure silicon and TiN/Ti-6A1-4V coating/substrate system were analyzed. The properties of the materials were assumed to be homogeneous and isotropic with a linear hardening behavior. The reverse method was used to extract material properties, such as the yield stress and strain hardening coefficient, from the numerical results by comparing the simulated indentation load vs. penetration depth (P-h) curves with those obtained experimentally. Both non-linear elastic and non-linear elastic-plastic analyses were carried out for the coating/substrate system. The results are given for four different coating thicknesses.

Jan 1, 2004

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By J. Moyes

The Intec Copper Process is an internationally patented hydrometallurgical process for the extraction of pure copper and precious metals from sulfide concentrates. Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The Intec Copper Process has several notable advantages over both smelting and other hydrometallurgical processes. Starting from a base of substantially lower capital and operating costs than any other conventional or developing process, the Intec Copper Process is economically viable at capacity levels as low as 15,000tpa-Cu, and capable of accepting low grade and metallurgically complex concentrates. Precious metals are recovered within the Intec Copper Process circuit, without the need to re-treatment of the environmentally stable solid residues. The Intec Copper Process offers the lowest energy consumption of the available technologies, with no liquid emissions or production of noxious gases. Unlike smelting, sulfur is recovered in the solid residues in elemental form.

May 1, 2002