Search Documents

By Z. Sun

The hydrogen embrittlement and stress-corrosion cracking (SCC) behavior of an a -titanium alloy and its two kinds of welding samples have been investigated. The results show that this alloy has very low susceptibility to SCC, and the values of Kiscc for the alloy are 46.4 MPa ? m' 65.86 MPa ? mu2 in the direction of T-L and L-T, respectively. The scanning electron fractographs show transgranular and quasi-cleavage fracture. The hydrogen embrittlement results show that the notch sample of the alloy is not sensitive to hydrogen, but the electro-beam welding and diving-arc welding samples are sensitive.

Jan 1, 2005

By J. R. Smith

"The Lake Dufault orebodies were discovered by deep surface diamond drilling. When a reasonable amount of outline drilling had been completed, the decision to go into production was made. The fact that shaft sinking, lateral development, the detailing of the orebodies and stope preparation were to be carried out as rapidly as possible necessitated very close scheduling.After a study of varions possible mining methods, an open-stoping system using long-hole blasting was chosen. Diesel-powered Transloaders were selected for the mucking and transportation of ore from the drawpoints to the orepass.At the time of writing, the choice of mining method appears to have been fully justified, although more time will be required to arrive at true operating costs and efficiencies."

Jan 1, 1966

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By K. Wongpreedee

Recovery and recrystallization of Au wire can degrade strength and alter conductivity properties during exposure to elevated temperature. Au Deformation Processed Metal Metal Composites (Au DMMC's) are being developed for electronic applications requiring high conductivity and high strength. This paper discusses the relationships between microstructure, strength, and resistivity of Au DMMC's. It also presents the results of a recent study on the elevated temperature stability of Au DMMC's of several compositions. Au-7 vol %Ag, Au-14 vol %Ag, and Au-vol 7%Pt DMMC samples were prepared by a powder metallurgy technique. All specimens were processed into wire by extrusion, swaging, and drawing. The smallest final diameter of these wires was 120 ?m. Thermal stability was analyzed by electrical resistivity measurements to determine the relation between transformation rates and time at elevated temperature. The extensive deformation used to produce these composites reshaped the initially equi-axed powder into filaments that are 30 to 100 nm in diameter and 16 to 180 mm in length. The small filament diameter confers high strength on the composite. The high conductivity can be explained by electrons flowing parallel to the filamentary microstructure aligned with the wire axis. Using the Avrami and Arrhenius equation relationships, it is possible to predict the times and temperatures needed to achieve various degrees of homogenization. The Au DMMC's were found to have good thermal stability compared to conventional coldworked Au interconnection wires. Although these composites will revert to solid solutions if exposed to high temperatures for prolonged time periods, their relative stability is sufficient to allow them to maintain their twophase microstructure during the anticipated lifetime temperature profiles of many products.

Oct 1, 2003

By R. Siwik, N. K. Davé

"The national reactive tailings (RATS) program is a co-operative industry-government effort to develop practical techniques for closure of reactive tailings areas. This paper summarizes the RATS program objectives and areas of research, and details the Noranda/CANMET project on the Waite Amulet tailings.Geophysical and biohydrogeochemical investigations were carried out at an inactive copper-zinc mine tailings site, Waite Amulet, in Noranda, Quebec. Geophysical investigations consisted of seismic, electromagnetic conductivity and electrical resistivity surveys to determine the thickness of the layers above bedrock and to map conductivity variations within the tailings and the immediate outlying area. Biohydrogeochemical investigations consisted of installing multilevel piezometer nests to determine groundwater flow patterns and porewater chemistry, obtaining solid core samples and characterizing for physical, chemical and mineralogical parameters, and iron oxidizing and sulphate reducing bacterial counts.The geophysical survey indicated a bedrock ridge extending under the tailings from the northeastern outcrop which may act as a porewater boundary layer. The survey also indicated a 2 to 20 m clay layer underlying the main tailings dam. Preliminary results of the saturated zone porewater chemistry have indicated three major zones of high electrical conductivity varying between 1,000 to 12,000 µs and pH between 3.4 to 8. Lower pH and high metal and sulphate concentrations were obtained in a shallow zone near the water table. With depth, the concentration of metal and sulphate ions decreased and pH increased below the water table. The underlying clay layer is relatively impervious -and most of the seepage from the tailings is probably exiting from the sides of the impoundment dam."

Jan 1, 1987

By A. E. Dyment

In formulating an explosive for any specific set of conditions, various factors must be taken into consideration. Is it to be subjected to water or moisture? .If so, it must be designed to have an inherent ability to resist water. Is it to be used in confined spaces underground, where ventilation is limited? If it is, it must possess qualities enabling it to form, upon explosion, the minimum quantity of noxious gases, such as carbon monoxide or oxides of nitrogen. Is it for use where low temperatures may possibly prevail? If so, it must be capable of resisting such temperatures without freezing. Is it for use where dust or inflammable gases may be present? If it is, then it must be so formulated as to produce, upon detonation, a flame of the lowest possible temperature and the shortest possible duration, in order to lessen the chance of ignition of such gas or dust. This is actually the essential property of a permitted explosive, and it is undoubtedly the most important characteristic of an explosive which is to be used in gassy or closed-light mines. This being the quality that distinguishes permitted explosives from other types, it is interesting to investigate the ways and means by which the low-flame-temperature characteristic is obtained . Generally speaking, such explosives are so designed as to contain comparatively small quantities of nitroglycerin and relatively large quantities of the strength-producing salt, ammonium nitrate. This ingredient does not develop as high a temperature upon explosion as does nitroglycerin, so its presence, in large measure, in place of nitroglycerin results in an explosive which has an inherent low-flame-temperature characteristic, as opposed to one which is .made up largely of nitroglycerin, which would ordinarily be in the high-flame-temperature class. Additions are also made of flame-quenching salts such as sodium chloride, ammonium chloride, and up to a certain limiting percentage of sodium nitrate. These salts, with the exception of the last, do not ordinarily take an active part in the explosive reaction, being present primarily to absorb heat liberated by the reacting ingredients.

Jan 1, 1947

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By G. H. K. Pearse

Sulphur is derived from both 'voluntary' and 'involuntary' production. The former category includes sulphur obtained from elemental sulphur deposits and from pyrite and gypsumanhydrite deposits. Sulphur in the latter category is produced by pollution abatement at fossil Juel plants and from treatment of metallic sulphides. Canada is the world's largest sulphur exporter and third largest producer. Main resources of Canadian sulphur are sulphurous fossil fuels, metallic sulphides and native sulphur. Only the first two sources have produced sulphur in Canada 10 date; the first source accounts for over 85% of total Canadian production. Future sulphur sources will be derived increasingly through pollution abatement and decreasingly through voluntary production.

Jan 1, 1984

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By I. Yarita

Magnesium alloys have the lowest density among the metals in practical use, and have properties such high specific strength, electromagnetic interference shielding and good vibration damping. Thus, there are many applications of these materials in automotive and electric parts. However, there is a little use of the products of metal forming of these materials because of poor plastic deformability in the normal temperature range and their high cost of production. To expand the range of application of products manufactured by metal forming, rolling technology for producing thin sheets having good mechanical and surface qualities is required. In this study, hot-rolled Mg-alloy sheets are experimentally rolled with or without lubrication in the temperature range from 293 K to 523 K. Rolling force, plastic deformability and surface quality are investigated, and the grain structures and their uniformity are observed. The effect of friction between the roll and the deforming material on the uniformity of the grain structure is discussed. Moreover, rolled materials are annealed and their mechanical properties are investigated by the tensile test and compared with those of as-rolled materials. The effects of the rolling conditions on the mechanical properties are discussed.

Jan 1, 2006

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the present study, the dynamic response of AZ and AE cast magnesium alloys to shock loading, are compared for strain rates ranging between 900 and 1200 s-1. Texture measurements showed that after shock loading, the (00.2) basal texture component of both alloys was strengthened. However, the strengthening magnitude was higher for AE samples. Also, it was observed that the twinning fraction decreased in both alloys with increase in the amount of alloying elements. In addition, cracks are formed at the interface between matrix and second phase particles in the AZ alloys. However, crack nucleation and fracture in AE alloys occurred at the sites where twins accumulated. Furthermore, analysis of the dynamic mechanical behaviors showed that the ductility of AE grade is higher than that of AZ alloy for all strain rates used in this research. This difference was explained by differences in deformation mechanisms of these alloys.

Jan 1, 2014

By Rodrigo A. Marinho

Erratic high grade values are as common in Nature as they are a source of problems for resource estimators. In some highly erratic metal deposits, less than 2% of the drilling samples can represent more than 10% of the total metal in the blocks and they are associated with a high risk level. There is a risk of local overestimation but also of global overestimation, with the high grades being projected over too large a volume. Capping or restriction of these outliers control is being widely used in the industry and commonly applied in resource estimation for the last three decades. The primary purpose of this paper is to present and describe the most applied methodologies for restricting the extrapolation of high grade samples and discuss the results based on a theoretical simulated model. Additionally, this paper demonstrates the economical impact associated with the high-grade and the project risk profile associated with each method.

Oct 1, 2009