Search Documents

By F. W. Wellmer

"I would like to comment on the classification scheme of ore reserves based on geestatistical and economic parameters as proposed by Wober and Morgan in the CIM Bulletin, January 1993.In principle, a classification system that combines quantitative data for levels of confidence and errors with economic expectations must be welcomed. I would like to point out, however, two aspects of the proposed classification system which might create ambiguities, and therefore problems, by working with two levels of confidence and two kinds of block sizes. A normal classification scheme reflects the information density, the highest reserve category such as class A, or proven, or measured reserves having the highest density. This is not necessarily the case in the scheme of Wober and Morgan (1993), unless the definitions are amended.I. Assuming, as the authors do, that the estimation errors show an approximately normal clistribution, at the 95% confidence level, the standard deviation has to be multiplied by about 2 for the error and, at the 84% confidence level by about 104. Reserves (or resources) with the same or even higher information density than class A reserves, which at the 95% confidence level would not fulfill the required economic criteria at the threshold level, i.e. not qualify as ""ore"" at all, could be retained ""on paper"" to class B reserves by just multiplying the standard deviation by the factor 104 instead of 2, thereby narrowing the error.This statistical ambiguity was partly inherent in the old German classification scheme which used varying confidence levels and errors (GDMB 1956; Jahns 1959). In the new German scheme, which was later adopted in Austria in a moclified version, the level of confidence was therefore fixed at 90070 for all reserve categories (Wellmer 1983; ONORM 1989)."

Jan 1, 1993

By Paul Delottinville, Maynard Hall, Henry Hillier

"An expert system application for supervisory control and optimization of the indurating process at the Iron Ore Company of Canada (IOCC) has been developed and installed in closed-loop. Prior to the installation of the expert system, the indurating machine was rebuilt and the instrumentation revamped. A Foxboro I/A Distributed Control System (DCS) was installed for regulatory control, and a new control strategy configured. The modernization of the regulatory control has resulted in significant improvement in both production rate and product quality. Expert system control was implemented in September 1996. Preliminary indications are that the expert system has further improved the consistency of product quality, enhanced fuel efficiency and increased productivity. The expert system considers both wet and dry sections of the circuit, and its optimization scheme is driven by pellet tumble index and compression strength. Statistical Process Control (SPC) rules were implemented in the expert system as part of the quality analysis and control scheme. The expert system application was developed and delivered using the Comdale Expert Optimizer (CEO), and has been in continuous closed-loop control since its installation. The system development and implementation is described, and preliminary benefits are presented..... IntroductionIn early 1996 the Iron Ore Company of Canada (IOCC) contracted Comdale Technologies of Toronto to develop and implement a real-time expert system for optimizing the indurating pelletizing furnace at our plant location in Labrador City, Newfoundland.The decision to install the expert system has been timely. Like many other resource-based industries in increasingly competitive markets, IOCC recognizes the need to find ways to improve the efficiency of our production process and ensure that product quality is maintained at the highest levels. With the Labrador City plant producing 11 million tons of iron ore pellets annually, implementing the best technology solutions to meet these objectives is critical."

Jan 1, 1998

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he's hurt. Maybe he's not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

May 1, 2010

By LUKE O. LINDOE

A major clay products industry in the Medicine Hat area since before 1910 has maintained a continued interest in the clays of the Cypress Hills. For the first forty years the materials used were local red-burning Cretaceous and Pleistocene clays and sands and high-quality stoneware clays of the Whitemud Formation at Eastend, Saskatchewan. Recently a much broader spectrum of raw materials has been brought into use. Including the exposures of the Eagle Butte structure, the Cypress Hills present a 1200 m section of clay-like sediments. Of this 1200 m about 94 per cent, the high montmorillonite shales of the Upper Cretaceous, can be considered useless, or nearly so; the remaining six per cent, all fresh-water beds, presents a wide variety of potentially useful materials. The development of these clay resources is complicated by deep surface creep on the south flank of the Cypress Hills, by largescale slumping on the north flank and by a structural complex in the Eagle Butte area.

Jan 1, 1984

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By M. Rafieazad, P. Fathi, X. Duan, M. Mohammadi, A. M. Nasiri

"Direct metal laser sintering (DMLS) is a metal additive manufacturing technology that creates highly complex components by fusing metal powder into a solid part. In this study, the impact of surface roughness on corrosion resistivity of AlSi10Mg_200C alloy manufactured through DMLS was investigated. The as-printed DMLS-AlSi10Mg _200C alloy was subjected to various surface finishing processes including grinding and sandblasting. The corrosion performance of the surfaces was then evaluated using potentiodynamic polarization testing and electrochemical impedance spectroscopy (EIS) in a 3.5 wt.% NaCl solution to mimic seawater environment. Surface characterization and corrosion morphology of the samples were assessed by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) spectroscopy. The results of this study show that the surface finishing process and the resultant surface roughness has a significant impact on the corrosion resistivity of the DMLS-AlSi10Mg_200C alloy in the seawater environment.INTRODUCTION Direct Metal Laser Sintering (DMLS), also known as Selective Laser Melting (SLM) (Sames, List, Pannala, Dehoff, & Babu, 2016), Laser Beam Melting (LBM), or Laser Metal Fusion (LMF) (Herzog, Seyda, Wycisk, & Emmelmann, 2016), is an additive manufacturing process that utilizes a precise, high-power laser to micro-join powdered metals and alloys layer by layer to form almost fully dense and functional components in three dimensions from the 3D computer-aided design (CAD) data. Complex geometries not possible with conventional manufacturing processes can be readily manufactured with high accuracy using the DMLS process with no need to time-consuming tooling."

Jan 1, 2018

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By S. C. Livanou, S. P. Tampouris, E. N. Zevgolis

In ferronickel (Fe-Ni) production from oxidized nickeliferous ores, mechanical losses of ferronickel in the slag are reduced by magnetic separation. Slag from the electric furnaces (E/Fs) contains 0.16% Ni. Its magnetic separation gave a pre-concentrate with 0.76% Ni, weighing approximately 6.5% of the feed. Nickel recovery was 29.7%. This pre-concentrate was then treated in a second (concentration) plant. Concentration treatment involves screening, crushing and magnetic separation. A pre-concentrate with 0.76% Ni gave a magnetic concentrate with 2.58% Ni and a non¬magnetic part with 0.35% Ni. Smelting of the non-magnetic part without the addition of a reduction agent in a laboratory electric arc furnace, gave a ferronickel alloy with approximately 20% Ni and a slag with 0.16% Ni.

Jan 1, 2005

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By David Morrison

Our present longwall problems in Cape Breton can be grouped under five main classifications. These are: (1) Roof control on the face and on the main roadways leading thereto. (2) Transportation of coal along face and levels. (3) Mechanical loading at the face. (4) Safe method of conducting and applying power at the working faces. (5) Dust nuisance. The usual layout for longwall operation in Cape Breton is to have three, and sometimes four, faces in line with each other, the length of face being from 400 feet to 500 feet (see Figure 1), and producing between 425 and 500 tons per face. Each wall is serviced by a well constructed roadway for transportation of coal, men, and materials, and is operated as an independent unit. Each wall works under a regular cycle of operations: first, cutting and boring; second, drawing hardwood chocks, building midwalls, and shifting panlines; and third, loading. The present method of roof control and operation of longwall faces has developed through trial and error since the commencement of longwall miring in Cape Breton. The basic method of roof control in all longwalls in Cape Breton is: rigid support of the roof in the immediate vicinity of the working faces by hardwood blocks, as shown in Figure 2, accompanied by a cushion support furnished by continuous midwalls, 12 feet wide, constructed of stone obtained from the waste and spaced at 50-foot centres. These midwalls are kept forward to within 4 feet to 10 feet of the working face and allow a gradual subsidence of overhead strata, thus preventing any sudden break at the working face.

Jan 1, 1947

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By Zou Lisheng

The culture of safety is very important to coal mining production. About 90% of mine accidents are caused by human error. This paper analyzes the status of China?s coal mining accidents, and accident cause. This paper explains the concept of safety culture, the value of safety culture, as well as the relationships between safety culture and safety behavior, and between safety culture and science and technology. The paper proposes the model of safety culture and the ways to enhance safety culture of coal enterprises. Safety culture and safety production is closely related and are significant to the improvement of mine safety situation in China.

Aug 1, 2013

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By Gilles Carrière

"The Suffield mine is situated five miles southwest of the city of Sherbrooke, in the Eastern Townships of Quebec. lt is the property of Suffield Metals Corporation Limited, a wholly owned subsidiary of Ascot Metals Corporation Limited.The old Suffield or Griffith mine had been worked intermittently from 1863 to 1906, without ever producing much ore. In 1951, diamond drilling done by Ascot Metals proved over one million tons of ore in three new bodies. The average grade of this ore was 0·018 ounces of gold per ton, 2-40 ounces of silver, l ·28 per cent copper, 0·59 per cent lead, and 6-45 per cent zinc. Since then the mine has been active, producing between 300 and 700 tons daily. More recent exploration has found continuations of the ore zones.General GeologyThe ore of the Suffield mine is found in porphyritic rhyolites of the Sherbrooke group (Silurian), at or close to its contact with sediments of the Beauceville group (Ordovician). The contact shows pronounced folds as well as irregularities due to erosion of the sediments prior to the outpour-ing of the lavas. On surface the general strike is north, and the dip is steeply east.The footwall sediments consist of interbedded black graphitic slates and. dark-coloured chloritic quartzite, overlain in many places by a thin bed of magnetite-hearing quartzite.The rhyolite host rock is a light grey rock, containing very abundant quartz and feldspar phenocrysts in a microcrystalline matrix of the same minerals. Some sericite is always present, especially in the vicinity of the ore zones, where the rock shows a pronounced schistosity.Several narrow basic dykes, with an easterly strike and vertical dip, cut all other formations. Most are lamprophyres, of either the monchiquite or camptonite type, but one has been identified as a diabase."

Jan 1, 1949

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

By Michael Farley, Paul Dufour

"Relationships, Partnerships,Marriages (RPM)RPM has a nice musical ring to it, but it is in fact synonymous with science and technology, university-government -corporate links and the more genera l issue of university roles in technology development. Pick up any report on one of these issues, and chances are that you will find one of these key words in the title. Play it, and you will find that the revolutions per minute are increasing. It is difficult to keep track of the wide variety of institutional experiments now developing in Canadian universities in attempts to marry science and research with technology commercialization and technology transfer.Why is the role of Canadian universities in this matter important? There are at least five good reasons:1. It is important because these knowledge institutions are producer s of scientific research, a major component of technology. Today the gap between the two is rapidly shrinking.2. It ' is important because Canadian industry is turning to universities for tech no logy development and new knowledge. Figure 1 shows that universities are becoming an important source of technology available to Canadian firm s; more important in fact than government. Figure 2 illustrates this trend more graphically in showing that university collaboration is one of the preferred methods of industry participating in co-operative R&D efforts:3. The role of Canadian universities in technology development is also important because the provincial and federal governments have embarked on various programs and policies for promoting the use of technology and science for economic benefit. Universities are playing an increasing role here. For example, the submission of IDEA Corporation (a venture capital operation funded by the government) in Ontario to the Bovey Commission on the Future Development of Ontario Universities clearly spelled out its ideas for commercialization of university research in Ontario . Among other things, the brief suggested that Ontario's universities need to be better equipped to transfer technology, and the reward structure in university research must incorporate industrial interests."

Jan 1, 1986

By J. T. Birkholzer, M. Rutenberg, K. -H. Lux, R. Wolters, J. Rutqvist, L. Blanco Martin

In this paper, we present numerical results corresponding to the Thermal Simulation for Drift Emplacement (TSDE) test, conducted in the Asse salt mine (Germany) between 1990 and 1999 to simulate reference repository conditions for spent nuclear fuel in rock salt. This test is of significant relevance for nuclear waste disposal in salt because extensive research and measurement programs were set up for the experiment. In our numerical study, we use two sequential simulators, TOUGH-FLAC and FLAC-TOUGH, and we investigate two-way coupled processes, focusing on thermo-mechanical analyses due to the main effect of heating. The two simulators used have recently been updated and are able to deal with large strains and creep processes. Moreover, specific constitutive relationships and coupling functions for rock salt and crushed salt under repository conditions are available. Within the framework of a benchmark exercise between Lawrence Berkeley National Laboratory and Clausthal University of Technology, the same scenario has been modeled in three dimensions using the two simulators mentioned. The main objective of the current, first stage of the benchmark is to evaluate the capabilities of these two simulators to predict relevant processes under repository conditions for high-level nuclear waste in saliniferous media. The comparison of the numerical predictions between them is very satisfactory, leading to a successful code-to-code verification. The comparison between measurements and numerical results shows that the most important processes are captured by the codes and constitutive models used. However, some differences exist between measurements and numerical results. These differences will be addressed in the next stage of the benchmark exercise, in which a parameter fitting effort will be undertaken. Overall, from the results obtained it can be concluded that TOUGH-FLAC and FLAC-TOUGH have the necessary capabilities to reproduce relevant processes under repository conditions for high-level nuclear waste in saliniferous formations.

Jan 1, 2015