Search Documents

By F. Rosenblum, P. Spira

"A correlation has been established between the oxygen demand of Brunswick Mining and Smelting ore and flotation results at the bench, pilot plant and operating plant scale. A method of dete""1llining the aeration requirement of sulphide ores on the basis of this correlation is presented. It is shown that abraded iron from grinding media plays an important role in aeration and flotation. Laboratory grinding must therefore be conducted under controlled conditions with suitable grinding media in order to obtain the true aeration requirement of the ore.A method of evaluating aerator efficiency, also based on oxygen demand measurements, has been used successfully at Brunswick Mining to design pilot plant and full-scale aeration systems.1. IntroductionPre-flotation aeration of sulphide pulps has been practiced in the Noranda Group for many years to help in the depression of pyrite and pyrrhotite and to promote chalcopyrite and/or galena. Recently, two out of three parallel circuits at the Brunswick Mining and Smelting Corp. Ltd. concentrator have been converted on a test basis to a new flowsheet incorporating aeration as a basic step. Among other benefits, a substantial decrease in the middlings load has been achieved as a result of improved pyrite rejection. There has been increasing interest in other organizations in the potential advantages to be derived from' aeration in terms of improved metallurgy and/or decreased reagent consumption."

Jan 1, 1978

By Willie Manfrey, Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of cres. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back -calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can he achieved through the judicious use of chemical additives.

Jan 1, 1977

By J. Farrell

The Canadian government ratified the Kyoto Protocol in December 2002 and, prior to ratification, committed to equitable distribution of the burden of implementation. The Federal government's Large Final Emitters group is working with industry to develop covenants that will consider the unique nature of the company's operations and not unreasonably burden any one sector or company. Ensuring equitable distribution must consider local, national and international issues. From a Canadian iron ore producers perspective, the fact that most of the iron ore production in the world is in countries that have no Kyoto commitment is a critical issue. Another issue unique to this sector is the increased addition of fluxing agents in iron ore pellet production which has shifted some process related greenhouse gas emissions from steel producers to iron ore producers. While the objectives of the Kyoto Protocol are primarily environmental, the economic implications for Canadian industry are not trivial. For decades Canadian companies have been actively improving energy efficiency and reducing greenhouse gas emissions to maintain a global competitive position. Production of iron ore pellets is an energy intensive process and the Iron Ore Company of Canada (IOCC) is the largest Canadian producer. In 2002 IOCC identified energy and Kyoto Protocol implementation as critical risk factors for their organization and appointed a full time Energy Manager. In January 2003, IOCC initiated a comprehensive process for identifying energy cost reduction opportunities and established an Energy Master plan. This process included:

Jan 1, 2004

By G. C. Bateman

THE cause of silicosis and its prevention have held the attention of medical men and mine operators for many years and at the present rime the study of this disease is more than ever to the fore, even though a considerable abatement in the incidence of silicosis has been noted of late. This abatement is due to individual and collective efforts. The Industry is keenly alive to the situation and much research is being carried on. Silica dust is assumed to be a contributing factor in the cause of silicosis. How it acts progressively in the early silicoric is nor fully understood. As the study advances, more effective measures of control may be evolved. At present the Industry has three known methods of reducing the incidence: 1. By thorough X-ray examination of all applicants, with special reference to chest conditions. Those who are considered to be susceptible to the disease are prevented from entering the industry. 2. Thorough ventilation of the mine. 3. Control of tuberculosis in mining centres and removal of miners when first symptoms of tuberculosis become apparent. In 1934, the Ontario Mining Association formed a Committee, known as the Technical Silicosis Research Committee, to study and supervise work on problems related to silicosis. This Committee obtained the full-rime services of a mining engineer to carry our research work at the mines in the Province of Ontario. The Ontario Mining Association has also provided funds for the purpose of carrying on research work along pathological and biological lines. This work is being done in the Department of Medical Research of the University of Toronto, in the Banting Institute, under the supervision of Sir Frederick Banting. The Silicosis Committee work in full cooperation with the doctors in the Banting Institute and provide material from the mines for the it use.

Jan 1, 1936

By G. M. Hughes

"400 cubic foot Agitair Flotation Cells are in use at Sherritt Gordon's Fox and Ruttan Mine Cu-Zn concentrators. The 4 impeller model No. 120, used at the Fox Mine Operation, appears to offer superior agitation and aeration qualities compared to the single impeller model 120A, in use at Ruttan. The advantages of the model 120 are most significant with ores of high specific gravity and coarse grind.IntroductionSherritt is using 400 cubic foot Agitair flotation machines at both the Fox and Ruttan Mine Concentrators.At the 3000 tpd, Cu-Zn Fox concentrator, 18 model 120 machines have been in operation since May, 1969.The 10000 tpd, Cu-Zn operation at Ruttan utilizes 49 model 120A machines. The plant started operation in May, 1973.The 4-impeller model 120 flotation cell has been marketed by Galigher since the early 1960's but the single impeller model 120A is relatively new.Model 120 Agitair -Cell DataThe Model 120 (Dwg. 1) has floor dimensions of 101 x 10' and a lip height of 2~ to 4 feet to provide up to 400 cubic feet of volume. This machine is shown with a froth crowder and stabilizer plates which are optional.Each motor drives two agitators. 20 HP is recommended by Galigher but 25 HP is more realistic with massive sulphides. The SG of ?ox ore is about 3. 6.The Model 120 can handle up to 600 cubic feet of air per cell at 2 psig which requires 5-6 HP at the blowers. Air volume to each impeller is controlled by a valve from a main header.During the first 3 years of operation at Fox there were few mechanical problems with the 120's."

Jan 1, 1974

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By Loris S. Pascoli

The increased pace of globalization in the mining industry has presented more opportunities for Canadian service companies to participate in ventures abroad. However, varying cultures, laws, competitive environments and contracting philosophies in other countries make it impossible to take for granted what is normal in the Canadian context. The author discusses some of his experiences and situations encountered in over 30 years in the diamond drilling industry, the last third of which were primarily focused on projects outside of this country.

May 1, 2001

By Vilkul Yuri

Operation of the iron ore deposits of Krivbass which has been going for 130 years, has led to serious problems related to reaching great depths in open pit and underground mining. Extraction of the huge volume of rock mass (about 9 billion m3) resulted in mass violations of the natural state of the subsurface. At present most mining operations are carried out either by combined open pit and underground mining or by open pits in areas underworked by underground mining. Now the process of movement of the strata underworked by underground mines is not completed ? work fronts of open pits approach the areas of possible funnel, terrace and fissure formation, movement continue to develop. With deepening mining operations the remaining reserves are worked off under layers of incumbent rocks of > 900 m. Significant underground voids arise from mining "blind" deposits at large depths. Heaving of voids over the mined area lasts for decades; it may result in not only unpredictable time of funnel emerging and area development of movement synclines, but also the threat of air blows in mines. Forced caving of incumbent rocks as a way of controllable backfilling is difficult to achieve for economic and technical reasons. This is much more expensive and dangerous than stoping. Furthermore, the mining practice does not know examples of enormous volume backfilling under a km thick rock layer. Currently, RMI "KNU" is conducting research and pre-design work directed at creating a specialized pilot Geoinformation System (GIS) of continuous remote monitoring of rock mass in areas of underground voids influence in Krivbass area. Implementation of this system will enable to determine promptly in time and space the areas of the beyond cut off stress condition, to inform about possible occurrence of events that may result in accidents and to improve safety of mining along with other systems of forecasting and controlling the stress condition in rock mass. RMI "KNU", with a large number of professionals from many Ukraine?s leading mining research centers, has developed a research and design work program that includes the following principal stages: 1. Analyzing geomechanical conditions of combined mining of magnetite quartzite and rich ore deposits; determining mechanisms of moving of rock strata underworked by underground mining and places of hazardous area monitoring. 2. Investigating anthropogenic factor influence on the safe state level of rock strata underworked by underground mining (laboratory studies). 3. Developing processing techniques for continuous remote monitoring of rock mass in areas of underground cavity influence. 4. Modeling the state of rock mass based on results of pilot GIS hardware measurements. 5. Developing an expert diagnostics system for rock mass state in areas underground void influence. 6. Experimental investigation and testing the GIS, its improving for efficient application. After testing the pilot GIS it is supposed to be implemented at all mining enterprises as an integral part of iron ore mining and processing technology in the Krivbass area.

Aug 1, 2013

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By G. Gauvin

Life span of aluminum smelting electrolysis cells can reach up to 3000 days. During this period, cathode blocks go under various physical and chemical changes that could result in an increase of electrical resistivity. The increase may be due to carbon migration from the cast iron to the steel bars, gap evolution between the cathode block and the cast iron, cathode cracking, etc. This paper focuses however only on the collector steel bar electrical resistivity evolution. To reveal the main phenomena responsible for the electrical resistivity increase, chemical analysis, metallographic and electrical resistivity tests were conducted on two steels bars picked from two Hall-Héroult cells after autopsies. Cathode voltage drop and temperature were measured using electrically insulated internal probes and thermocouples on 16 samples from each steel bar. Electrical resistivity can reach up to 1.21µO-m for a steel bar aged 2505 days compare to 0.142µO-m for steel AISI 1008 at room temperature.

Jan 1, 2011

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By J. Dupre, A. Gontcharov, H. Pepin

Produced by the conventional TIG welding CMSX-4 welds had been studied. It was demostrated that microstructure of welds depended on filler materials, welding parameters and joint design. Epitaxial solidification of CMSX-4 clad deposits produced a directionally solidified structure while welding with the similar filler material. Defects free clad welds were obtained by TIG welding without preheating using similar and dissimilar filler materials.

Jan 1, 2006