Search Documents

By Maurizio Violo, Arjan Beqiraj, Umberto Masi

"Abstract - Four main podiform occurrences of chromite have been distinguished in the ultramafic Bulqiza massif, Albania; they are associated from the bottom to the top with: i) basal harzburgites (lower tectonite sequence), ii) dunitic lens-bearing harzbugites (middle-upper tectonite sequence), iii) layered chromitite-bearing dunites of transitional zone, and, iiii) the stratigraphically lowermost part of the magmatic section. However, only the occurrences hosted by rocks ii) and iii) are economically important.Chromite compositions similar to those of other podiform chromites are bimodal. Thus, chromites from occurrences ii) and iii) are richer in Cr than chromites from the other two occurrences. Accessory chromite disseminated throughout the massif is richer in Fe than orebody chromite, displaying similar range of the Cr/Cr+Al ratios, with accessory residue chromite matching the characteristic (Cr/Cr+Al >0.6) range of type-III Alpine peridotites. Both orebody and accessory chromites show compositional ranges correlating with host-rock compositions, i.e., the Cr-rich chromites are hosted by the most refractory ultramafic rocks. Therefore, the Cr/Cr+Al and Mg/Fetot (Cr/Fetot) ratios of chromite are useful for exploration of high-grade, metallurgical chromite ore at Bulqiza and in other massifs of similar geodynamic setting."

Jan 1, 2000

By E. S. Moore

GOLD was discovered previous to the year 1900 on the east shore of Emerald lake, Afton township, Timagami Forest Reserve. It was found in a small cavern in banded iron formation, close to the water's edge. This occurrence of gold was mentioned in several reports that referred briefly to this area, and prospectors evinced considerable interest in the region. It was not, however, until the Golden Rose Mining Company, which was incorporated in 1909, started operations that much work was done on the property. In 1915-16, this Company, under the direction of E. J. Townsend, the President, did a considerable amount of work. A small mill was built and ore was extracted from pits, trenches, and a one~ hundred-foot shaft. In 1927, Afton Mines, Limited, was incorporated to take over the property, and about thirty men were employed for a time. During 1934, the New Golden Rose Mining Company was organized to handle the property, and the Consolidated Mining and Smelting Company of Canada, Limited, undertook to develop the mine. In March of the following year, this Company began deepening the shaft from 100 feet to 500 feet. A considerable amount of drilling had previously been done on the hill of iron formation in which the mine is located. Further drilling was done from the surface, and altogether about twelve holes have been put down to test the formations. Over 2,000 feet of drilling has also been done from the underground workings. The mine is now known officially as the New Golden Rose mine, although to many it is better known as the Afton. To reach the property during the summer months, there is a boat trip of about thirty miles from Timagami, a wagon-road portage of one mile to Obabika lake, a boat trip of ten miles on this lake, and finally a wagon-road portage of one and one-quarter miles to Emerald lake. The mine lies about three-quarters of a mile down the east shore of the lake. A 75 h.p. Diesel engine and compressor were taken in over this' route last summer, and it is evident that the transportation problem is quite a serious one. Airplanes have been much in use, and a winter road runs from the mine to Chudleigh, on the .Canadian National railway near Sudbury.

Jan 1, 1936

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By O. Lashkari

Swirled Enthalpy Equilibration Device (SEED) is a new patented Slurry-on-Demand, SoD, processing route. The semi-solid slug preparation is carried out by off-center swirling of aluminum melt in a metallic mould. As part of the current research program on the semi¬solid processing of aluminum alloys, the morphological evolution of 356 aluminum foundry alloy microstructure is reported here. Semi-solid slugs were prepared using two different pouring temperatures of 645°C and 695°C respectively. Morphological evolution of the semi-solid microstructure was characterized using image analysis through measuring of primary a-Al particle size, number density, aspect ratio and sphericity. The possible relationships between microstructural features and process parameters were also investigated. The current report covers the effect of pouring temperature on the morphology of primary a-Al dendrites and attempts are made to explain the differences between the predicted percentage primary a-Al phase and those of the actual values in the as-cast slugs.

Jan 1, 2004

By Man-Chao He

One of the critical problems involved in deep coalmines is unusual gas emissions. Many researchers agree that there is a relationship between coal gas emissions and geological features such as tectonics or geological disturbances, gas content, properties of the coal and rock and the mininginduced stress state in the coal seam and rock. Thus, the present paper intends to investigate complex mechanical phenomena during the process of gas emission in underground coal-mines. A program of laboratory testing was undertaken to study the effects of temperature and pressure on mechanisms of gas emission. It must be noted that this paper describes new techniques developed to simultaneously measure deformation and gas pressure, as well as flux during the test, taking the characteristics of gas transport into consideration under certain temperature and pressure conditions. The results indicate that under certain temperature and pressure conditions, gases adsorbed to coal start to desorb, and increase the pore pressure. High pressure gases entering coal fractures can generate high tensile stresses near the crack tips, leading to crack propagation and coalescence, which in turn can cause the specimen to dilate. From the experimental viewpoint, these test results may help us discern why mining seismic events can trigger gas emissions.

Aug 1, 2013

By B. T. Lu

The corrosion and wear properties of a series of chrome white iron (CWI) castings were study using electrochemical and low-stress sliding abrasion tests. The results confirm that the corrosion resistance of these materials is largely dependant on the quantity of chromium in the matrix, while the wear resistance is mainly controlled by the volume fraction of chromium carbides. A pseudo-wear/corrosion map is developed to identify alloy compositions that may be suited for erosion/corrosion conditions.

Jan 1, 2005

By M. Mirnezami, J. A. Finch, M. S. Hashemi A.

This study examined the effects of pH and sulphate concentration on the surface charge and stability of alumina and pyrite dispersions. The relationship between these properties was investigated using measurements of electrophoretic mobility and settling velocity. The maximum aggregation for both minerals was observed near the iso-electric point (iep) where the force of repulsion is at a minimum. Aggregation decreased at pH values away from the iep, where an increased surface charge causes electrostatic repulsion between particles. Zeta potential data revealed that sulphate ions were adsorbed only on positively charged surfaces for both minerals. Adsorption of sulphates on the alumina surface increased aggregation by reducing the surface charge from >+25 mV to close to zero. These results indicate an electrostatic bonding of sulphate ions to alumina surface. Preliminary results on the interaction of pyrite and sulphate ions indicate a similar response.

Jan 1, 2004

"Since World War II, urban communities have expanded at an unprecedented rate. The industrial mineral industry supplies the sand, grave], limestone, crushed rock, cement, gyp-sum, etc. for urbanization. Most de-posits in use are close to or within communities. Pollution of water and air has become a matter of public concern. Waste disposal and the effects of noise and vibration are subjects of public debate. Need for the reclamation of land after operations such as strip mining is discussed in magazine articles and on TV pro-grams; i.e., the general public is educated in the unattractive features of mining.Legislation is on the books and being drafted to regulate mining operations and their side effects. To avoid over-regulation and restrictive legislation, it is necessary that the public be educated and legislators informed of problems peculiar to the mining industry. Our side of the story needs publicity."

Jan 1, 1968

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By W. A. Crosby, W. K. Smith, K. L. McDonald

"IntroductionThis paper describes how the introduction of two blasting techniques and the resuItant development of new dragline digging methods have increased the productivity of single- and double-seam dragline operations at the Rietspruit opencast mine.LocationRietspruit , one of South Africa's largest opencast strip mines, is situated some 11 5 kilometres east of Johannesburg in the Witbank coal field.BusinessRietspruit is a joint venture between Transvaal Consolidate d Land and Exploration Company (T.C.L.) and Shell, South Africa. Rietspruit is administered and managed by Rand Mines, the Mining division of Barlow Rand, transportation and marketing being the responsibility of Shell. The total saleable coal product, approximately 5,5 million tons per annum, is exported via Richards Bay.Presplitting and Throw BlastingPresplitting was initially introduced in September 1980, as a means of dewatering t he overburden and mid burden to facilitate the use of dry-mix explosives a s opposed to slurry explosives.The utilization of the throw blasting technique arose as a direct result of observed ground movement after the successful introduction of presplitting. The first trials commenced in March 1981 on the double-seam operation. The methods, economics and resulting advantages are fully described elsewhere. A brief description follows.Method of PresplittingAfter determining the desired presplit line, 250-mm holes are drilled to top of coal at 4-m to 6-m intervals, dependent on the competency of the rock overlying the coal. A single 60-kg charge of slurry explosives is located at the bottom of each hole, no tamping is used and all the holes are detonated simultaneously. The results are a competent, straight, vertical highwall. This enables accurate control of the first row of blast holes closest to the highwall, which is a prime requisite for successful throw blasting."

Jan 1, 1983

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By M. Aljarrah

The phase equilibria in the Mg-Al-Ca system was investigated experimentally by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques similarly the Mg-Al-Sr system has been studied using DSC and XRD as well as scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and quantitative electron probe micro-analysis (EPMA). A new ternary solid solution MgxAl4,xSr was confirmed in Mg-Al-Sr system, which is a substitutional solid solution of Mg atoms in Al4Sr. Maximum solubilities of 21.3 at.% Al in Mg17Sr2 and 11.4 at.% Al in Mg were observed. It was also noticed that Mg38Sr9 dissolved 12.5 at.% Al. In the Mg-Al-Ca ternary system, one of the invariant transformations predicted by thermodynamic modeling was verified experimentally and found to occur at 512°C with composition close to 10.8 at.% Ca, 79.5 at.% Mg and 9.7 at.% Al. A ternary solid solution (Mg,Al)2Ca was confirmed where large solid solubility of Al in Mg2Ca was observed.

Jan 1, 2006

By A. C. Drost

The mining industry has been put under closer scrutiny in recent years, which has led to the adoption of a plethora of initiatives in countries around the world and by international organizations, some voluntary and others mandatory, governing economic, ethical, social and environmental practices of this industry. In order to plan appropriately, secure project financing, build value and manage risks, it is imperative to identify and understand the application of this new and evolving regime, which can be described under the general label of corporate social responsibility (?CSR?) law, and to incorporate compliance policies into the day-to-day operations of mining companies. Our paper and presentation will describe this new legal framework, which includes both ?soft? law and ?hard? law adopted at the international and domestic level that governs the actions of mining companies, particularly when operating in developing countries. While the notions of hard and soft law may seem abstract and grounded in legal theory, this paper shall demonstrate how these concepts concretely apply to companies in general, and to mining companies in particular. An analysis of the recent case law in this area as well as examples of corporate ?best practices? will illustrate the application of this body of law. As will be demonstrated through the case law, non-compliance of CSR law (both ?soft? law and ?hard? law) can lead to economic penalties, difficulties in accessing capital, loss of social licenses and even the withdrawal of permits and concessions. This confirms that now more than ever, ethics and sustainable practices in mining are fundamental to building a successful business model.

Aug 1, 2013

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015