Search Documents

By M. Niinae, F. Nakahara, T. Kawamoto, T. Suzuki

"MgO was chosen as an As(V) immobilization agent and a series of immobilization experiments was performed to obtain insights into the behavior of As(V)and MgO during leaching tests. Our experimental and modeling results demonstrated that As(V) immobilization by MgO consists of the following steps: (i) an increase in soil pH, (ii) desorption of As(V) from the soil, and (iii) the re-immobilization of As(V) by MgO/Mg(OH)2particles. Regarding the behavior of MgO, the modeling results showed that when the MgO dosage was 25 mg MgO/4g-drysoilor less, the majority of MgO was used to increase pH, and less than 1% of MgO was used to sorb As(V), which was consistent with the result of leaching tests showing that a high level of As(V) was leached at the MgO dosages. On the other hand, when the MgO dosage was above 25 mg MgO/4g-drysoil, the percentage of MgO used for As(V) sorption increased up to 35%, and correspondingly, the As(V) leaching level decreased to below 0.01 mg/L As at an MgO dosage of 75 mg MgO/4g-drysoil.INTRODUCTIONOne of the major arsenictransport pathways causing groundwater contamination is the migration of arsenicfrom artificially or naturally contaminated surface soils. Therefore, in this study, the immobilization of arsenate (As(V)) in soils was investigated using commercial-grade magnesium oxide (MgO) as a potential cost-effective measurement to prevent the occurrence of groundwater contamination with As(V).With respect to the use of MgO for remediating As(V)-contaminated environmental media, MgO has been used in several studies to remove As(V)from water(Yu et al., 2011; Jia et al., 2013; Tresintsi et al., 2014). Although these studies demonstrated that MgO effectively removes As(V)from water in water-MgO systems, the behavior of As(V)in water-soil-MgO systems has not been evaluated in the literature, and several questions remain to be answered to comprehensively evaluate the use of MgO as an As(V)immobilization agent in soils. For instance, as is well-documented in the literature(Ford, 2002; Lenoble et al., 2002; Zeng et al., 2008), iron oxy-hydroxide (FeOOH) is one of the important adsorbents for As(V)in both natural and engineered systems. Therefore, it is anticipated that the presence of FeOOH in soils significantly influences the behavior of As(V)in water-soil-MgO systems and consequently, the immobilization performance by MgO. Another important question to be answered is the behavior of MgO during the immobilization treatment. In our previous studies (Suzuki et al., 2013a, 2013b), commercial-grade MgO was demonstrated to effectively immobilize lead and fluoride, and the immobilization effectiveness was indicated to last more than 100 years against the exposure to acid rain (pH 4.0). However, these studies focused on the behavior of contaminants. As a result, little is known about the behavior of MgO during the immobilization treatment. The lack of understanding of the behavior of MgO during immobilization treatment is one of the main concerns leading to relatively low public confidence in immobilization treatments."

Jan 1, 2016

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By F. W. Gray

Ideal utilization of the heat energy in coal should theoretically be secured by supplying each atom of combustible material present with the exact quantity of oxygen necessary for complete combination. An intimate and equal admixture of the fuel particles with air is therefore to be sought. Coal, or the combustible substances of which coal is composed, may be used in solid or liquid or gaseous form. The use of coal in small particles intimately mixed with air is, in effect, a specification of coal in pulverized or dust form. There has been much important development of this manner of using coal, which may be instanced as the outstanding advance in the use of coal as a solid. The completeness and efficiency of combustion in a properly designed dust-fired furnace permits the use of locally available coals of inferior quality, and enables them to be used commercially instead of imported coals of better quality. That is to say, some grades of coal of low calorific value, that are not economically useable in lump form on grates, are useable in pulverised form, because of the more complete combustion thereby obtained, and the consequent more efficient results. In the case of coals that are unsuitable for steam-raising in grate-fired furnaces, because of clinker troubles, (arising usually from a combination of high sulphur content and low-temperature fusibility of the ash content) use in pulverised form has obvious advantages, and in addition gives the benefit of any heat units that are contributed by free sulphur in the coal.

Jan 1, 1924

By Doug Barnstable

"Quinsam Coal Ltd. is assessing the potential of developing a thermal coal deposit near Middle Quinsam Lake on Vancouver Island. The coal reserve outlined is classified as a high-volatile, bituminous ""A” steam coal and is composed off our separate seams of varying quality within the Late Cretaceous Comox Formation.Open-pit mining methods will utilize a walking dragline and a truck / shovel module as the primary stripping tools. Following washing and mechanical drying in a Baum jig preparation plant, the coal will be transported to the proposed dock at Campbell River for shipment via 55, OOO-DWT vessels to world markets. The paper will outline the development and status of the project to date. IntroductionQuinsam Coal Ltd. is a joint venture of Weld wood of Canada Ltd. and Luscar Ltd . The participants propose to develop a thermal coal mine in the Middle Quinsam Lake area, 17 miles inland from Campbell River on Vancouver Island (Fig. I). By acquiring all the assets of Canadian Collieries in 1962, Weldwood also came to own the coal rights of the area proposed for development. Luscar Ltd . ha s been designated as project manager until completion of construction and thereafter will act as operator of the mine.Surface mining methods will be used to produce approximately 1.0 million short tons of coal annually from the Quinsam property. Seven separate mining pit s will be developed along with the supporting minesite facilities, including a proper paration plant. Transportation routing to Campbell River and the establishment of docking facilities will be required. The initial economic life of the mine is 12 years, with the provision to extend this in the future by developing higher-ratio, auger or underground reserves."

Jan 1, 1980

By Rory S. McLaren

"Cost per ton as it relates to mobile underground vehicle maintenance and repair is invariably astronomical. The reason: the mechanic replaced a ten micron filter with a 250 micron filter because it appeared to be physically identical; the purchasing agent bought ""Brand X's"" filter because it was 25% cheaper- the result, a filter life 30% less; the hydraulic pump was sent for repair at a cost of $2000.00 and failed shortly after installation; pumps are failing because there is no testing equipment available in the workshop.This paper will identify a number of the common pitfalls resulting in high costs, and offer solutions to bring these costs to within acceptable limits.The following key issues will be discussed:A. Genuine parts replacement versus ""Brand X""B. Evaluating outside repair shopsC. The influence of environmental conditions on optional equipmentD. Personnel trainingE. Servicing and testing equipmentIntroductionThere is an old English aphorism, ""Look after the pennies, the pounds will look after themselves"".This paper is aimed at the pennies.Genuine Parts Replacement versus ""Brand X""High interest rates and floundering mineral prices are forcing many equipment owners and operators to purchase ""Brand X"" or ""Pirate"" parts in order to survive. ""Pirate"" part manufacturers invariably offer lucrative discounts which are most appealing to the average purchasing agent whose responsibility it is to save money. Unfortunately, in most cases, there is a tradeoff involved; when the price drops so does the quality, which can adversely affect owning and operating costs. Unless totally obvious, ""original"" or ""pirate"" part metamorphosis requires scrupulous analysis by competent individuals.Hydrostatic transmissions have been used successfully for many year s in various industries. They found their way into mobile underground loaders in the early seventies and have since become very unpopular in mining circles due to their apparent ""inherent unreliability"" and near ""prohibitive"" repair costs. The big benefit of the hydrostatic transmission is compact component packaging which enables the machine to work in very small headings."

Jan 1, 1983

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By V. S. Papezik

Pyrophyllite, a hydrous aluminium silicate, is used mainly in the ceramic industry and to a lesser extent as a filler in the manufacture of paper, rubber, insecticides and baby powders. Commercial deposits of pyrophyllite in North America are restricted to the "Avalon Zone" , a belt of late Precambrian volcanic and sedimentary rocks that extends along the eastern flank of the Appalachian orogenic belt f rom Georgia to Newfoundland. The only commercial Canadian pyrophyllite deposit lies near Foxtrap on the A valon Peninsula of Newfoundland. Here, steeply dipping lenses of altered pyrophyllite rock occur in a north-trending rhyolite belt near the contact with a granitoid pluton. The altered rock is massive, light greenishyellow and contains varying proportions of pyrophyllite, sericite and quartz with lesser amounts of diaspore and traces of barite and rutile. A lteration was produced by acid solutions, either derived from or activated by the intruding pluton, at temperatures of 250° to 270°C and pressures not exceeding 2 kbr. The largest of the Foxtrap pyrophyllite lenses, discovered in 1897, was mined intermittently f rom 1903 until the early 1950s. The present owner of the mine, Newfoundland Minerals Limited, acquired the property in 1959 and ships between 27, 000 and 36,000 tonnes annually to th e company plant in Lansdale, Pennsylvania, for use in ceramic tile.

Jan 1, 1984

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995

By M. Hamamoto, M. Furuta, S. Tanaka

The Tamano smelter and refinery has expanded its production from 228kt/y to 260kt/y since 2006. It was not a big jump, but efficient and economical improvements were executed. These were not only de-bottlenecking and modernization of the smelting plant, including the acid plant, but also additional processes were commissioned, e.g. slag cleaning furnace and steam dryer. On the other hand, a conversion to permanent cathode process in the #2 tank house made the biggest impact on production efficiency for the refinery plant. In order to overcome the drastic change of copper business, although each scale is not so big, continuous improvements are very important to survive. This paper mainly describes the recent improvements of the smelting plant.

Jan 1, 2007

By S. Kashani Nejad, M. Bellino, K. Collins, C. Tovee, J. Godwin

Motivated by safety considerations, logistical issues, transportation cost savings, product diversification, and marketing preferences, several uranium producers are revisiting their business models and supply chain configuration and, instead of selling dried yellowcake to downstream refineries, they are moving to build in-house calcining facilities. Drying and calcining plants are relatively low-cost facilities to build and operate. The execution period of a typical yellowcake drying and calcining project is also relatively short and alternative construction methodologies, such as modularized solutions, are available. The drying and calcining technologies used for yellowcake are relatively mature, environmentally contained, and well supported by qualified vendors. The drying and calcining circuits also seamlessly integrate with upstream and downstream operations. These either produce a dried yellowcake or calcined U3O8 which are notably safer and easier to transport and market. This paper presents an overview of the recommended technology and project development considerations for yellowcake drying and calcining facilities.

Jan 1, 2020

By N. Dobrin, R. Sheinman, Y. V. Kokotov, L. N. Braginsky

Increasing the production of a Mixer-Settler unit requires either increasing flow rates or increasing extractant concentration. The mixers still have to ensure complete emulsification and to maintain high values of specific interface surface area in order to provide a high rate of mass transfer. Theoretically, an increase in mixing intensity can support increased flow rates without reducing extraction efficiency. Unfortunately, conventional pump mixers and mixing systems create small droplets that do not separate easily. As pumping action and mixing intensities are increased, the quantity of small droplets increases. We describe the development and industrial application of a novel mixing system for efficient mass transfer without forming significant quantities of small droplets, targeting both high mass transfer rate and low entrainment values.

Jan 1, 2014

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

Adaptive processing is often related to the mineral composition of the mining block currently processed. The portions of waste, ore and secondary product minerals considered are always positive and typically sum to 100% (i.e. a composition). A typical solution to predict block averages of spatially dependent quantities would be block kriging. However, kriging is based on spatial correlations and it has been repeatedly shown that correlations of compositional data are spurious and blurred by the constant sum constraint. Aitchison (1982) proposed a general solution for compositional problems, based on transforming the compositional data to a set of logarithms of ratios of components, and analysing the transformed scores. The transform is chosen to be invertible to ensure that no information is lost in the process. This methodology avoids spurious correlation problems and ensures coherence between results obtained with different subcompositions. Pawlowsky-Glahn and Olea (2004) adapted the approach for point-support geostatistics, allowing the prediction of point compositions from spatially neighbouring data, without the artefacts induced by standard multivariate cokriging. Unfortunately upscaling the results of this approach with block cokriging is not straightforward, because of the nonlinearity of logratio transforms. Furthermore, we have to consider those nonlinearities created by the dependence on the block composition of extraction efficiency and processing costs of the possible processing choices. This paper proposes a solution for predicting the conditional expectations of the benefit of processing the block with each processing choice using geostatistical simulations of the local values of the composition and the resulting block integrals. The computation for a large number of blocks can be done efficiently using Cholesky decomposition. The approach also allows the calculation of prediction errors for expected compositions and expected benefit at almost no additional computational cost. Such compositional approach is necessary, for example when processing choices depend on proportions of certain minerals after other components have been removed; or if processing alters the composition in a multiplicative way, by partially removing a portion of some components.

Aug 1, 2013

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968