Search Documents

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By Stephen B. Cheeseman

The quantity of data available and the rate at which we access such data are rapidly increasing. Electronic data capture systems, fleet management systems and a host of other technological advancements have created a constant stream of real-time, tactical data. However, are we taking advantage of this data? Are we converting data into useful information to aid in efficient decision-making? Mining operations are struggling with ?information overload?, finding it difficult to extract the benefits from vast stores of data. Without the necessary tools to facilitate a data filtering and information reporting process, most operations revert to old practises such as re-entering data into multiple spreadsheet reports. As a result, the ability to make effective use of data still eludes many mining operations. Some operations have taken audacious steps to rectify this situation. The De Beers Venetia mine in South Africa has implemented an integrated mining information technology solution that transforms their data into practical, usable information allowing staff and management to make decisions that improve efficiencies and reduce costs. In the absence of quantitative justification or ROI, De Beers took a risk in implementing change. Today, they are realising the benefits. This paper will unearth the information technology issues that surfaced during the Venetia implementation, then identify the benefits De Beers has obtained from deploying an integrated mining information technology solution at the Venetia mine.

May 1, 2002

By L. K. Nenonen

"Given the properties, locations and quantities of material to be hauled and the dump locations and capacities, the designer wishes to select the type and number of trucks and loading equipment required. Accordingly, software is being developed to assist in creation of the equipment, material and road network data bases, in selection of equipment, materials and road networks from these data bases, and in evaluation of the expected productivities both in a rapid, non-interactive, approximate fashion and a more detailed interactive fashion which permits the user to act as superintendent, if he so chooses. The basic technology has been developed and applied to an open-pit copper mine and is being refined and generalized for oil sands and coal mining applications.BackgroundA set of mathematical and interactive computer models are under development to aid in the selection of equipment and operating policies for an open-pit oil sands mine being planned by Canstar Oil Sands Ltd. This paper describes the computer models being developed of truck haulage systems. Although the interactive truck haulage model is based primarily on a model developed by the National Research Council in collaboration with Glenayre Electronics Ltd. of North Vancouver and Lornex Mines Limited(2).(3l, substantial changes and improvements are being incorporated to greatly increase its generality re equipment types, road network characteristics, dispatching and supervisory policies, etc. Although this paper is principally devoted to the truck haulage model, discussion is included concerning its interactions with other models."

Jan 1, 1982

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan's position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By J. J. Barakso, C. Tarnocai

This paper outlines a method of testing for the mercury content of rocks, soils and plants. Techniques of sample collecting are described and the analytical procedures outlined. Examples are given of mercury determinations in two known mineralized areas in British Columbia - Copper Mountain Mines and Pacific Nickel Mines.

Jan 1, 1970

By M. L. Jeremic, G. J. P Delaire

"The mechanical aspects of cable bolt failure are considered from the point of view of properties of grout and cable, as well as of the rock in which it is anchored. The results from recent investigations made in-situ as well as in the lab are combined and presented with reference to other work done in the area. An attempt is made to stimulate the thinking along these lines so as to initiate further research which may enhance the design of cable bolting as it applied to mining operations.IntroductionIn the past twelve year s systematic cable bolting has found application in many areas. In civil engineering rock anchors have been used to provide tension at the heel of a dam permitting the reduction of its cross section. They have been used in retaining walls to reduce construction time and costs by eliminating the need for struts and braces which complicate pouring the foundation walls. It is also possible to use rock anchors in providing reactions where tall buildings are subjected to uplift on one side due to wind forces. Cantilever bridges may be constructed by implementing rock anchors to provide anchorage requirements. Anchorage piles or dolphins or mooring ships have also been built using these. In the mining area rock anchors, commonly known as cable bolts because they are made of hoist cable may be implemented in the reinforcement of hanging walls or to retain rock slopes.In order to sustain de-pressurized ground where rock separation developed along the pressure arches, cable bolts were utilized at the Tsumeb Mine in South-West Africa and also at the Strathcona Mine in Sudbury, Ontario, In both places old degreased hoist ropes were installed in downholes from crosscuts above a given stope and then grouted without tensioning. Jeremic and Cassidy described the use of cable bolts to increase hanging wall stability and postpone fracturing, in addition to producing pre-support for improvement of stope back stability."

Jan 1, 1983

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By B. M. Das, V. J. Hucka, J. H. Tu

Subsidence can cause serious damage to surface installations such as railroads, highways, pipelines, buildings and other facilities over a period of many years. Although total elimination of the effects of subsidence is difficult, the damage can be minimized through a systematic analysis. An example of such a study for reducing the effects of subsidence on pipelines is presented in this paper. Subsidence-induced stresses on a pipeline over some coal mining properties in Utah have been analyzed using a computer with graphics capabilities. The results are useful in predicting the extent of damages due to mining subsidence. In view of the gradual replacement of room-and-pillar mining by longwall with caving, this sort of analysis will become more and more important. In the next phase of this study the predicted results will be compared with the permissible stress levels on pipelines over actual subsided areas in an actual case.

Jan 1, 1989

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By I. Imris

The chemical industries are using different type of catalysts, which after application usually produced many tons heap of residues. One of them is cupric oxide catalyst with high content of copper and silica. The recovery of copper from the waste has become major interest from a viewpoint of environmental protection and recycling of resources. The thermodynamic analysis and experimental results suggest that the copper from cupric oxide catalyst can be extracted by plasma reduction process. By plasma reduction process the inert slag and copper with following chemical composition: 99.04 % Cu, 0,042 % Fe could be obtained.

Jan 1, 2007

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By D. A. Peterson, R. Pakalnis, G. Peter Mah

"Laboratory and trial installations have been completed to determine the potential of composite cable bolt reinforcement in Canadian underground mines. Several prototypes of glass fibre cable bolts have been developed and tested, two of which are currently available to the mining industry. Their evalualtion consisted of lab testing in Canada and the United States, along with trial installations in several underground mines throughout Canada. The objective was to develop a cost competitive composite cable bolt equivalent in strength to that of a 16 mm (Ys in.) diameter steel cable bolt. In addition to achieving equal or superior load carrying characteristics in tension, the glass fibre cables generally experienced an increase in the rate of installation due to their lighter weight. Unlike conventional steel cables, composite cables may be installed within mines which utilize continuous excavation and which require cuttable support. A market analysis of cable bolt usage in Canada has been completed. Glass fibre cable bolts are an effective means of rock reinforcement in mining applications. They prove to be a viable alternative to conventional steel cable bolting. IntroductionCurrent cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to support the surrounding rock mass. Cable bolts are a form of internal support and are generally used as pre-support in open stope and cut-and fill mining methods. They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, are generally less than 20 m (65.6 ft) and are untensioned. A major advantage of cable bolts is that they are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils. This allows relatively long lengths (>20 m, [65.6 ft]) to be installed in areas with limited head room (1.8 m)."

Jan 1, 1994

Operating and Social Considerations from a Contractor?s Perspective

May 1, 2013

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By Robert B. Parsons

"Canadian income tax legislation contains a number of provisions which serve to facilitate the structuring of business arrangements, including mineral resource ventures. These rules are often fairly complex and not easily understood. This article attempts to explain in plain and understandable language the mechanics and benefits of one of the more frequently encountered provisions, the ""Section 85 election"".IntroductionThe Canadian resource industries are probably singled out for more special attention under this country's tax legislation than any other industry. This special treatment is, of course, not always welcomed by the industry, such as where unnecessarily restrictive taxation is perceived to exist or where agonizingly complex tax legislation must be dealt with. On the other hand, certain provisions in the tax legislation treat the industry in a relatively favourable manner, including a number of rules which, in recognition of the high risk and capital requirements of the resource sector, serve to facilitate the structuring of resource ventures."

Jan 1, 1984

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

By A. Dahi Taleghani, Amir Shojaei

A continuum damage mechanics (CDM) based constitutive model has been developed to describe elastic, plastic and damage behavior of rock during drilling. In addition to inelastic deformations, this model incorporates rock anisotropies like toughness anisotropy due to the bedding planes orientation that is a common observation in soft Shales. The pressure sensitive inelastic deformation of porous rocks together with their damage mechanisms are studied for drained and undrained conditions. Fracture mechanics of microcrack and micro-void nucleation and their coalescence are incorporated into the formulation of the CDM models to accurately capture different rock failure modes. The performance of the developed elastoplastic and CDM models are compared with the available single cutter test data of a specific shale play and then the models are introduced into a commercial finite element package through user-defined subroutines. A workflow to derive the required model parameters is presented through inverse modelling of the single cutter test data. The developed CDM model outperforms the traditional discrete element and fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures like formation of the cuttings ribbon without any essential need for remeshing. This model would provide a robust tool for modeling bit performance and rate of penetration using conventional elements of FEA with a reliable results and a computational cost less than similar computational techniques like discrete element methods.

Jan 1, 2015