Search Documents

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By Brendan Parker, Tyron Rees, Steven Hart, Abba Manesh, Ian Mcgaffin

"In September 2009, Newmont began the commissioning of a 3 stage crushing and milling circuit at its Boddington Gold Operation in Western Australia. The Boddington ore has been recognized as one of the hardest and most abrasive ores treated to date and this played a pivotal role in the selection of crushing and HPGR technology for this operation as opposed to the more conventional SABC circuit.This paper will examine the scale up from laboratory to pilot plant and full scale operation of the crushing circuit. There have been many challenges to overcome in the first 18 months of operation; however, the HPGRs have in general met design expectations and performance is expected to improve further with ongoing design changes"

Jan 1, 2012

By A. E. Boudreau

It has long been recognized that platinum-group-element (PGE) deposits in layered intrusions preferentially occur in intrusions that crystallized from high-Mg parent magmas. Recent studies suggest that evaluation of any given intrusion for economic PGE potential should also include assessment of the PGE, sulfur and chlorine concentrations in the cumulates and potential parent liquids. PGE: Magmas that contain relatively abundant Pt and Pd are the best candidates for forming economic deposits. Although analyses of coeval sills and dikes are the best indicators of primary magmatic PGE concentrations, analysis of the cumulates themselves is also valuable. For example, within the Stillwater complex, background PGE values in cumulates from the ultramafic sections of the complex contain, on average, several 10s of ppb Pt and Pd. Background concentrations of this order are suggestive that the magma was not depleted in the PGE. Sulfur: Conventional petrogenetic models for the formation of PGE deposits in layered intrusions require the PGE to have been concentrated during a magmatic sulfide-saturation event. In contrast, some hydro thermal models suggest that sulfur and the PGE were mobilized from footwall cumulates by upward-migrating, high-temperature hydrothermal fluids. Both models suggest that significant PGE deposits are likely to occur at and below the level where stratigraphic increases in whole rock sulfur concentrations occur. Chlorine: In both the Stillwater and Bushveld complexes the cumulate sequences below the major PGE-bearing zones contain anomalous Cl-rich apatite. The chlorapatite component of apatite in these rocks may exceed 40% and, in the Stillwater complex, typically exceeds 90%. It is stressed that pristine igneous mineral analysis and not whole rock data be used, as whole rock Cl concentrations may be affected by very localized (grain boundary), low-temperature alteration. Intrusions that crystallized from high-Mg, high-Cl magmas appear to have the best potential to host significant PGE deposits.

Jan 1, 1995

By Heather Budney

Objectives 1. Evaluate the effectiveness of ON?s EA processes using criteria from the EA and policy sciences literature. 2. Recommend improvements to the EA processes and draw lessons from the ON case for the consideration of other jurisdictions. Evaluation Process 1. Chose criteria ? 14 primary criteria (Wood 2003) ? Subcriteria from Wood (2003) and Lasswell (1971) 2. Gathered information ? 6 key informant interviews ? Published literature, policies, legislation 3. Assessed criteria and formed Recommendations

May 1, 2008

Electric Vehicle Controllers Ltd. ?EVC started in 1981 ?Underground electric locomotive drive systems ?Developed tandem load sharing system and radio ELOS controls ?Locomotive autonomy systems ?Entered space technology development in 1999 with NORCAT to develop Mars drill for CSA ?Commercial distributor for drilling systems, lunar physical simulants, electric mobility systems and lunar mining technologies

May 1, 2009

By D. A. Barr

"Most of the lode and placer gold production in the Canadian Cordillera has been derived from mines and placers in the Intermontane and Omineca belts. Gold has been produced from rocks of Precambrian to Eocene age, but the preferred host environment contains Upper Paleozoic to Upper Jurassic eugeosynclinal or arc-type sedimentary and volcanic rocks adjacent to plutonic complexes which have a wide variety in both size and composition. Auriferous quartz lodes occur in fissures and shear zones which are commonly subsidiary to strong fault zones. In common with most vein-type deposits, structural complexities are an essential part of the mine environment.Gold production from the Canadian Cordillera to the end of 1978 totals 35.0 million ounces, of which 47 per cent has been produced from placer mining, principally in the Klondike and Cariboo districts. The balance has been derived from lode gold (80 per cent) and base metal (20 per cent) mines.Gold reserves in producing mines and deposits committed for production as of January 1, 1978 were 87.4 tons, or 21.6 per cent of total Canadian gold reserves contained in all types of deposits. Although more than 100 lode mines have operated in the Canadian Cordillera since the turn of the last century, over 75 per cent of the lode gold produced by 1978 was recovered from five mining camps, namely the Rossland, Hedley, Bridge River, Premier and Barkerville.The average grade of the principal producers in these camps was about 0.45 ounce of gold per ton. Individual camps yielded from 3 to 8 million tons during their operating lives, which varied from 28 to 43 years. The last of these mines ceased operating in 1971.Most of the total lode gold production has been derived from quartz veins, frequently with associated carbonate and ankerite, occupying fractured and faulted zones in Mesozoic volcanic and sedimentary rocks closely associated with a variety of intrusions. A review of the literature suggests that several deposits may have evolved by remobilization of ore constituents from earlier concordant gold-bearing formations. The principal metallic minerals in the deposits are native gold, electrum, tellurides, pyrite, arsenopyrite, pyrrhotite, sphalerite, galena and chalcopyrite.As the mineralogy suggests, many of the Cordilleran lode gold deposits have yielded important co-products or byproducts, including silver, copper, lead, zinc, cadmium and tungsten. Significant by-product gold production has also been derived from porphyry copper, volcanogenic, replacement and pyrometasomatic deposits, particularly in recent years.No major lode gold discovery has been made in the past 67 years, although little exploration activity for gold has taken place during the last 30 years. Several relatively small lode gold and gold replacement deposits have been discovered in recent years, either serendipitously (Chappelle) or on very low initial budgets (Northair and Carolin). Based on well-established precedents, one or more of these may eventually be developed into a large mine.A detailed study of the Canadian Cordillera gold deposits based on recent genetic models could prove rewarding, not only in up-dating information on their origin and depositional characteristics, but in stimulating the search for undiscovered gold deposits, in the Cordillera and other parts of Canada."

Jan 1, 1980

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GRG) test procedure at McGill University is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill University has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GRG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. Around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill University. As a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GRG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GRG tests were carried out at McGill University on ores from all over the world. Recently, a modi?ed version of the GRG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GRG in a sample; this simpli?ed test has the advantage of reduced mass, processing time and cost. To recognize and honour the contributions made by the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GRG test be named after Laplante.

Jan 1, 2010

By A. Dave Mackintosh

The Current demand for potash has pushed world prices to record levels and allowed Saskatchewan producers to operate at maximum capacity. Several years of strong demand has resulted in a permitting rush not seen since the 1960?s. Even though Saskatchewan has a huge potash resource, mining and processing constraints will limit the areas of economic development. Introduction In 1969 M. E. Holter prepared a report ?The Middle Devonian Prairie Evaporite of Saskatchewan?, published by the then Dept. of Mineral Resources. Holter?s report has remained the bible of geologists working in potash ever since. It is astounding that a report written before there was really much potash mining history in the province, is as valid today as when it was first published. This paper re-iterates much of Holter?s report and adds a little mining experience to essentially confirm the importance of his work.

May 1, 2008

By Alf Hartling

"Most of the Paleozoic section of the Williston Basin is a thick accumulation of numerous carbonate to evaporite, shallowing upward, cyclic sequences. These sediments were deposited in broad epeiric seas, and the deposition of the evaporite facies marked the final stage of each cycle. Many of the sequences display a pervasive replacement dolomite in the uppermost portion of the carbonate units. This secondary dolomitization is, at least in part, an early diagenetic event, synchronous with evaporite deposition.The inception of evaporite precipitation resulted in the seepage of a dense, Mg-rich brine into the underlying sediment. The heavy brine moved down the gentle regional dip displacing the more normal marine interstitial pore fluid and dotomitized the primary calcitic sediments en route. The supply of Mg-ions decreased away from the source, and correspondingly, the degree of dolomitization decreased and larger crystals formed because of slower nucleation at fewer sites.The seepage refluxion of dolomitizing brines gave rise to the frequently observed textural variation of cryptocrys talline, impervious dolomite grading into a finely sucrosic, permeable dolomite down-dip. This diagenetic facies change provides the critical up-dip barrier for potential hydrocarbon reservoirs. The lateral pool boundaries are controlled by either structural relief or a similar diagenetic facies change. The reservoirs are capped by the tight evaporites.Hydrocarbon production is attained from diagenetic traps in the Mississippian Oungre Zone and the Ordovician Red River 'C' Zone . Reservoir creation and the pooling mechanism are the result of dolomitization by the seepage refluxion of dense, Mg-rich brines beneath restricted, hypersaline lagoons. When formulating an exploration/ exploitation program for these oil prone horizons, it is essential to understand the complete geological history in order to establish where the reservoirs will be found and to define the areal extent of each accumulation."

Jan 1, 1984

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By J. Vaughn Barrie

Placer mineral deposits may exist in the nearshore and shelf regions off western Canada. These deposits could contain gold, ilmenite or zircon as well as sand and gravel aggregate. Two deposit types typical of the British Columbia offshore are: (l) modem and relict gold/titanium beach deposits; and (2) reworked relict titaniferous shelf deposits. The preservation of drowned beach heavy mineral concentrations resulted from a rapid relative sea level rise across the shallow shelves approximately 10 500 years ago, particularly off the Queen Charlotte Islands. This same transgression submerged an outwash fluvial system that had been exposed for at least 3200 years, draining areas of known gold placers.

Jan 1, 1994

By F. Chiesa, Jeremy Carignan, B. Duchesne, D. Levasseur

"Aluminium A206 (AlCu4) is one of the strongest aluminium casting alloys with tensile properties approaching those of ferritic ductile iron. If the specification on the silicon content (< 0.05%) is easy to achieve during alloy ingot production, it is not the case in a foundry, where returns are used which are not perfectly cleaned from the silicate containing molding sand (Olivine). In alloy A206, the Si content is controlled in order to avoid the formation of a low melting point intermetallic phase (such as phase Q Al5Cu2Si6Mg2); these phases will melt during the solutionizing heat treatment to which alloy A206 must be subjected to develop its outstanding mechanical properties. This incipient melting may deteriorate the mechanical properties of Alloy A206 if the solutionizing treatment is applied at the standard temperature of 530°C.In the present study, a lower temperature solutionizing (520°C) was applied to a high Si content 206 alloy in order to reduce or eliminate the possible incipient melting. This was carried out on a complex shape industrial casting weighing 14 kg (31 lb) and 560x410x250 mm (22x16x10”) in size poured in aluminum 206 with a high silicon content (0.22% vs 0.05% max for alloy A206). Twenty ASTM E8 subsize tensile specimens were excised from two locations in the casting in order to compare the tensile properties for the two solutionizing temperature used (530 and 520°C). Optical and SEM microscopy allowed to investigate the causes of the differences in the properties observed between the 2 zones of the casting studied for 3 different heat treatments. INTRODUCTIONIn spite of their “textbook” outstanding mechanical properties (Up to twice the strength and elongation of the widely used A356 alloy), aluminum-copper alloys of the 2xx series are seldom used because of their propensity for hot tearing [Li, 2011], the segregation of copper [Cho, 2003], and their sensitivity to stress corrosion cracking [Jean, 2009, p. 113)]. Also, because of their wide freezing range and high thermal conductivity, a wide mushy zone makes feeding difficult, unless strong temperature gradients are created by liberal use of chills and risers in the critical zones of the part. Because they are prone to hot tearing, grain refining of Al-Cu alloys is particularly important, titanium playing a major role in the process [Sigworth, 2003]; grain refining has also been shown to be beneficial to fatigue strength [Jean, 2009, p. 103]. The practical basis of foundry practices pertaining to these alloys is outlined in an AFS webinar [Weiss, 2014]."

Jan 1, 2016

By X. -G. Chen, A. M. Nabawy

A novel manufacturing technique for Al-TiB2 nanocomposites has been developed, in which TiB2 nanoparticles were incorporated into liquid aluminum under mechanical stirring and in the presence of a K2ZrF6 flux-wetting agent. The microstructure of the Al-TiB2 nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microhardness test was conducted to investigate the strengthening effect of TiB2 on the aluminum matrix. The TiB2 nanoparticles were successfully incorporated and dispersed into the aluminum melt in the presence of the K2ZrF6 flux during mechanical stirring. In the as-cast microstructure, most nanoparticles segregated in the interdendritic regions as a result of particle redistribution during solidification. The addition of 2, 5 and 10 wt% TiB2 nanoparticles increased the composite hardness by 60, 90 and 150% respectively when compared to commercial purity aluminum, indicating that the TiB2 nanoparticles imposed a significant strengthening effect on the aluminum matrix. The role of K2ZrF6 flux agent on the incorporation of nanoparticles into aluminum melt was discussed.

Jan 1, 2014

By Tom Shumka

Introduction ?This technique detects 100% of all gear tooth surface indications, providing comprehensive data, and has the ability to size indications accurately. ?The remarkable advantages of ECA technology, is improved inspection capabilities and significant time-savings. ?The advantage of using EMCD is its ability to size indications accurately. ?This technique does not require the gear teeth to be wiped down by hand after cleaning as in MT, LT or UT inspections. (Figure 1) ?This technique will inspect one gear tooth in 30 seconds. ?All of the data can be archived for future comparisons in an electronic report. Methodology ?This technique utilizes Eddy Current Array (ECA) as the principle inspection technique. ?What has been added are specialty scanner probes with multiple coils, a multiplexer and a software package. ?With 2 and 3D dimensional isometric displays, the defect can be seen electronically as it is on the gear tooth surface, thus, reducing the reliance on human interpretation.

May 1, 2011

By Jeffrey S. Loen

"The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 x thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009