Search Documents

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By J A. Gilliand

Mineralogical cross sections of orebodies on the 300-,600- and 900-foot levels of the Coronation mine have been interpreted in terms of centers of mineralization. The maximum concentration of chalcopyrite occurs closest to these centers, with pyrite and pyrrhotite concentrated some distance away. The magnetite concentrations are farthest removed from the centers. A hydrous halide fluid model is established. Attempts to explain the observed mineralogy by the action of temperature gradients on the fluid model were unsuccessful. Likewise, the action of diffusion alone on the fluid model cannot explain the observed mineral distribution. The concept of attenuation is introduced-i.e., the rate of diffusion of a particle species is related to the product r2 I/ M, the attenuation coefficient, where r is the particle radius and M its molecular weight. Attenuation, acting on the fluid model alone, will not produce the observed mineral distribution, but, when considered together with the action of temperature gradients, the observed mineralogy can be well explained by the combined effects of these two processes on the assumed fluid model.

Jan 1, 1965

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By N. Saracoglu, J. P. Golightly, R. H. Wallis, J. J. Brummer

"The McClean uranium deposits are in northern Saskatchewan, 11 km west-northwest of the Rabbit Lake mine. Their average grade is 1.8% UJ0 8 and they contain 6,350 tonnes of uranium oxide in seven pods of variable grade and mineral assemblage. They are hosted by both basal Athabasca Group and the regolith developed on the underlying crystalline basement. The major mineral facies are: sulphide, arsenide, 'bleached', and hematite, with the important uranium minerals being coffinite, uraninite and pitchblende.Abundances of carbon and sulphur isotopes are consistent with their derivation from pyritic graphite in basement gneisses. Isotopes of oxygen and hydrogen suggest mineralizing fluids were aqueous and at temperatures of about 200°C. Ar39/ Ar40 laser age determination of illite indicates mineralization began about 1300 m.y, ago and that significant hydrothermal alteration ceased about 1170 m.y. ago though Pb/U data suggest the deposits continued to evolve into the Mesozoic.The deposits are interpreted as the result of oxidizing ground water stripping uranium and other metals from either the Athabasca sandstone, especially the heavy mineral layers, or from the regolith, and precipitating these when encountering a warm reduced fluid emanating from the basement."

Jan 1, 1984

By R. D. Brown

For the first time in years, the spring budgets of federal and provincial governments have not brought down major new proposals affecting the tax burdens of the mining industry in Canada. It seems appropriate to use this unaccustomed period of tranquility to set out an extremely abbreviated summary of the principal features of the federal and provincial income and mining tax rules affecting the mining industry.

Jan 1, 1977

By R. P. Charbonnier

"To understand the operation of jigs and other separating processes based on differences in gravity, it is desirable to analyse the motion of various particles in given media under specific conditions. A summary of the earlier theories shows that they lead to unsatisfactory or excessively complicated formulae in cases such as coal jigging. By adopting a simplified theory of the motion of particles in a fluid, the size and duration of the initial accelerated motion of a particle falling in hindered settling can be calculated. Based on this mathematical analysis, examples referring to actual coal jigging practice show that it is desirable to prolong and/or repeat, as frequently as possible, the optimum conditions corresponding to an effective acceleration of the particles. The separation is then obtained according to gravity rather than to particle dimensions, as would be the case if the velocity of the particles• were allowed to approach its terminal value. To achieve this gravity separation, it is suggested that the suction phase of the jigging cycle be artificially prolonged and the frequency of pulsations increased as much as possible for washing the coals of smaller sizes."

Jan 1, 1959

By Earl T. Hayes

This paper briefly reviews the laws enacted in the United States governing the coal miner. It discusses amendments to the Coal Mine Safety Act and describes the provisions of the Metal and Non-Metallic Mine Safety Act.

Jan 1, 1969

By J. A. Russell

MR. M. W. Boom: I would like to congratulate Mr. Russell on his fine paper. One very good point which has always appealed to me is the smooth working of a steam hoist as compared with electrical. He does not mention the steam hoist at Springhill which has been working there for a good many years. MR. S. R. NEWTON: I have read with a great deal of interest the paper presented by Mr. Russell on the development of haulage engines in the mines of the Dominion Steel & Coal Corporation. He is to be congratulated on having produced a comprehensive article showing, step by step, the various improvements that have been made over the years in the design of such engines. I am quite in accord with Mr. Russell's statement that the positive tooth clutch can have too many teeth, and also that the method of driving a sliding clutch hub of any design should be by means of a hexagon or octagon on the shaft. Where the clutch hub does not of necessity slide on the shaft it can be pressed on and keyed to the shaft in the normal manner. With regard to the 'Cramp' internal-expanding jaw-type clutch, while it is true there are more moving parts than with the clutch consisting of a ring with internal cut teeth and a driver having a fewer number of teeth as .described by Mr. Russell; there are compensating advantages to the internal expanding jaw-type of clutch. The V shaped profile of the teeth permits of engagement of the clutch with very much less 'jockeying' of the drum. This is particularly the case in vertical-lift mine hoists, where it may be necessary to engage and disengage the clutching mechanism at frequent intervals.

Jan 1, 1944

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By Harry R. Oldale

This paper first covers the general and economic geology of the Coxheath Hills area, and then outlines the exploration and mining development that has been carried out since the first discovery of copper in the area in 1875. The work of Mariner Mines Limited from 1963 to the present time is detailed, particular attention being paid to the recent discoveries of copper, silver and lead mineralization that have greatly enhanced the potential of the area.

Jan 1, 1967

By Nur Hossain

Analysis of Linear Elastic Fracture Mechanics (LEFM) parameters via the Virtual Crack Closure Technique (VCCT) has been obtained for SENT specimens of AM6OB magnesium alloy. It is found that the ratio of initial crack length to initial monotonic plastic zone size is one of the critical factors in establishing the limit of using LEFM concepts. If this ratio is below a certain limit (i.e. when crack lengths are small in comparison to the plastic zone size), loss of similitude stress intensity factor range would occur. This ratio, therefore describes the limit below which the use of LEFM would no longer be admissible. In this study, the above limit was established for AM6OB magnesium alloy. In addition, fatigue crack propagation tests were conducted to ascertain the fatigue response of the alloy and determination of the coefficients of Paris model.

Jan 1, 2010

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013