Search Documents

By Rodrigo Craig Cerello

The Brazilian economy has always presented a strong correlation with the mineral activity. Since colonization days, due to the territorial expansion caused by the explorers search for gold, mining in Brazil became a basic sector of national economy. Currently, the Brazilian mineral sector¹ estimates a 550% production increment (Figure 1A) in the last 10 years, reaching the US$ 50 billion value, reflecting the increased global demand for raw materials from mineral origin. According to the Brazilian Constitution², mineral resources belong to the Federal State and, consequently, their exploitation must be authorized, under penalty of engendering federal crime. Furthermore, activities of this nature are prone to cause environmental degradation such as, but not limited to, deforestation, pollution, soil deterioration and water contamination. The GPEMA represents the forensics group of the Brazilian Federal Police responsible for the technical analysis of traces related to crimes against the environment and consequently, illegal mining cases.

Aug 1, 2013

By Farzaneh Abedini, Narain Hariharan, Lucas C. McFarlane, Nikolas A. Romaniuk, Tiffany Thayne

The use of dewatered mine tailings as backfill material (commonly referred to as ‘paste’ backfill), is the most practiced form of backfill in Canada providing significant environmental benefits by reducing the size of external tailings facilities and improved economics through enhanced resource recovery. Paste backfill operations reuse filtered mine tailings with a cementitious binder and water to create a slurry that is hydraulically transported to refill underground stopes, later forming a structural network of cemented tailings in the mine stopes. Unlike typical structural applications that utilize General Use (GU) Portland cement; modern paste backfill operations maximize strength performance by blending Portland cement with ground granulated blast furnace slag (GGBFS) or other supplementary cementitious materials (SCMs). GGBFS and other SCMs offer key performance benefits and carbon reductions; however, the availability of these SCMs is rapidly dwindling in today’s carbon-constrained economy. This paper examines the development of an alternative binder system that provides similar performance and carbon reduction to that of GGBFS for mine backfill operations. The binder utilizes the chemical reaction between a reactive source of aluminosilicates and available calcium from calcium oxide or calcium hydroxide to replace between 50 to 100% of GGBFS. The performance of the binder is examined with insights into the hydration mechanisms that generate mechanical strength in the cemented paste network. Paste backfill slurries require precise engineering to create a material that maintains flowability during pipeline transport and generates enough strength to meet operational targets once placed in the stopes. Engineering of such slurries requires large amounts of water to be added to the binder-tailings matrix, far exceeding the typical water to binder ratios used in concrete mix designs. This characteristic of paste backfill warrants great emphasis on understanding the hydration mechanisms of the binder used in the paste backfill system. GU cement is typically composed of 50-70% tricalcium silicate and 15-30% dicalcium silicate.  The hydration mechanisms of these compounds consume 4 to 6 units of water to mineralize into calcium silicate hydrate cemented phases that result in compressive strength development. Cementitious aluminate and aluminosilicate phases make up 5-20% of GU cement and aid in secondary performance characteristics such as set time. Certain calcium aluminate hydrate phases such as monocarboaluminate and ettringite mineralize 10 to 32 units of water into their crystalline structure. Hydration products such as ettringite are traditionally avoided in construction applications due to their propensity for volumetric expansion after cement setting, leading to micro-fissures and subsequent strength degradation (known as ‘sulfate attack’). This paper proposes that such hydration products benefit the strength development in paste backfill slurries with the aforementioned characteristics due to their greater potential to mineralize free water. The newly developed calcium aluminosilicate binder is designed to replace 50-100% GGBFS or other SCMs used in paste backfill systems and meet operational strength requirements by providing exceptional hydration characteristics through cementitious reactions. Additionally, the aluminosilicates used have a minimal carbon footprint and a secure supply outlook, thereby allowing mine operators access to a low-carbon binder option throughout the mine’s lifespan.

May 4, 2025

By P. Klossek

It is estimated that China accounts for 94% of the world supply of rare earths (Roskill, 2011). This fact, together with the impact of China?s export policy, poses a substantial risk to the security of the rare earth supply as well as a rare earth price risk. This situation has motivated an increase in the number of rare earth projects under development, i.e., there are currently more than 440 worldwide (Technology Metals Research, 2012). However, economically and environmentally acceptable processing technology to produce tradable products from rare earths (e.g., separated rare earth oxides) is not freely available on the market at the moment. In this respect, a lot of research and development has been initiated on this topic, in academia as well as in industry. Using a proprietary model and scenario-based analysis, we studied the impact that the development of rare earth processing technologies would have on the rare earth market and the economic feasibility of rare earth projects mentioned before. The analysis showed that this impact varies depending on the technology type (e.g., technology can affect project production volume, cost structure or both) and the legal context of the invention (e.g., free or limited by patenting availability of a new technology). The effect of a technology which influences project production volume is not the same as of a technology which changes project cost structure. The impact of a patented processing technology differs from the impact of a processing technology which is freely available on the market. In the case of a new technology which is limited by patenting, its impact depends on the market position (?producing?, ?next-coming?, or ?not producing? project) of the patent holder. The paper contributes to existing research by studying the dependence of the expected micro- and macroeconomic impact of rare earth processing technology developments on the properties of a new technology (e.g., costs, legal framework etc.). By this means, the paper adds to existing knowledge and attempts to make the rare earths market more transparent and predictable from a perspective outside China.

Aug 1, 2013

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By J. Coffin, M. Muinonen, D. Fragomeni, R. Multani, C. Deredin

"Rejection of pyrrhotite from pentlandite is of critical importance to the economics of nickel concentrate production and the main goal of the Strathcona milling operations. A joint team of XPS, Glencore Technology and Strathcona Mill personnel executed a comprehensive program of work to develop and implement strategies for increased Po rejection with focus on challenging ores containing high feed Po/Pn ratios (> 7) and significant hexagonal Po content (> 40% of total Po). This paper describes the team results including minerology, bench-scale flotation tests, and plant validation tests and modeling that have defined the path forward to improving the metallurgical performance and economics of the mill operation. Techniques to quantify hexagonal and monoclinic pyrrhotites were developed at XPS to assess the differences in their metallurgical behavior since their flotation responses are quite different. Mineralogical tools including QEMScan were extensively used to determine mineral liberation, associations, optimum grind size, and nickel deportment into pentlandite, pyrrhotite and non-sulphide gangue. Several reagents/strategies were evaluated during bench-scale flotation testing to significantly increase Po rejection. A significant shift in the Po-Pn selectivity and grade recovery curves was achieved using several strategies including the use of DETA and sodium metabisulfite, and regrind of the rougher concentrate and rougher cleaner/rougher tails.INTRODUCTION The Strathcona Mill is owned and operated by Glencore Nickel – Sudbury Integrated Nickel Operations and has been processing Ni-Cu ores from the Sudbury Basin since 1968 (valuable sulphides: pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2). Currently Strathcona Mill receives ore mined from two main sources in the Sudbury area and produces two concentrate streams – a nickel-copper concentrate that is shipped to the Sudbury Smelter and a copper concentrate that is sent to the Fonderie Horne (Glencore Copper, Rouyn-Noranda). The general flowsheet currently used at Strathcona is displayed in Figure 1. It is highlighted by separate feed circuits for regular grade Ni ores and high grade copper ores. The copper circuit has a preflotation stage prior to a rougher-scavenger stage, a copper-nickel separation circuit, and a pyrrhotite (Po) rejection circuit."

Jan 1, 2018

By J. H. Gray

"IntroductionIn 1980, Fording Coal Limited started conceptual planning studies which led to major changes in the long-range mining plan at their Fording River Operations. These new plans have been completed and are now in operation.To assist personnel in a timely completion of this major revision to the long-range plan, existing in-house drill hole data base and scheduling systems were used and a computerized Mine Modelling and Planning System was purchased. With these tools, plan s were developed which led to completion of initial access to the peak of Eagle Mountain and the start of mining operations in March 1983. As mining area s open up and new geo logical data is obtained, detailed plan s are being extended and revised.With the geology and mine plan s on line, this work can now be done with less effort and plans ca n be adapted to provide flexibility in mining operations. Changes in market conditions can be accommodated by moving mining operations into different seams for different coal types. The computer systems are used to revise pit designs and schedules accordingly."

Jan 1, 1986

By Robert B. Parsons

"1984 was an eventful year in the courthouse f or observers 0/ the mining tax scene in Canada. For the first time in a number of years, the Federal Court heard several important tax cases which pertain directly to the resource industries. Tax Notes discusses/our cases that could affect the taxation 0/ operations and investment in the mining sector.Capital Gain or Income?Ever since tax reform, risk-takers in the exploration business have maintained that the taxation of capital gain s is a significant impediment to raising risk capital. It must be akin to rubbing salt in the wound, then, when an entrepreneur sells shares and the Court upholds Revenue Ca nada taxing the gain as ordinary income instead of capital gain. But, this is precisely what happened in the case of The Estate of Murray Watts, et al. v. The Queen.The issue that had to be decided by the Federal Court, Tri al Division, in this case was whether or not the profit from the sale of shares in Hearne Coppermine Exploration s Limited in 1968 was a capital gain, or income subject to tax.Hearne was incorporated in July, 1967. At that time, the three plaintiff s, together with seven other individuals, subscribed for 400,000 shares at 10 a share. The plaintiff subsequently subscribed for an additional 500,000 shares at $1.A pooling agreement was entered into by all ten shareholders regulating the disposition of any o f their shares; any sale required approval of seven of the ten initial sub scribers. It also provided for the sale of their shares 30 days after any public offering."

Jan 1, 1985

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By Ben C. McLellan, Philip J. Bangerter, Andrew Murphy, Glen D. Corder, Damien Giurco

Sustainability now forms a critical part of metallurgical plant design. In addition to compliance with requirements and corporate principles, design engineers must also consider how community and societal responses to the metallurgical industry affect the way they design and build plants. Three broad areas to consider are: the design engineer’s contribution to sustainability through the design process and the relationship to the social license to operate (SLO)—the unwritten license communities give companies to safely and responsibly operate the plant and equitably share benefits; the realization of sustainability goals through methodologies emerging in the design activities; and the integration of design frameworks into a contemporary project design context and its investment objectives. This chapter explores sustainability in metallurgical plant design in the context of SLO, design tools and frameworks, and community and societal influences.

Jan 1, 2015

By Robert Yobou, Jacques Naho, Benjamin A. Allou, Jacques Carignan, Huan-Zhang Lu, Jayanta Guha, Koffi Pothin

"Résumé - Les seules productions de columbo-tantalite en Côte d'Ivoire sont effectuées dans les éluvions, colluvions et alluvions d'Issia, au Centre-Ouest de la Côte d'Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n'a été accordée à l'étude de la minéralisation primaire en relation avec l'évolution de ces granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent: le granite orienté à deux micas (type Lobo), le granite orienté à muscovite dominante (type Bitapia) et le granite porphyroïde non orienté à muscovite dominante (type Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale montrent que: (1) les trois principaux granites de la région sont de type-S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite de type Issia fut le dernier à se former.Les pegmatites liées au granite de type Issia ont été classées en quatre types : A- pegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et D- pegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV- zone à microcline massive; V- zone à quartztourmaline. Ces pegmatites présentent une zone d'altération métasomatique externe.La minéralisation de Ta, Nb, et Be est liée à la zone III des pegmatites de types C et D, la minéralisation de Li est associée aux greisens qui peuvent être observés n'importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite de type Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite de type Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite de type Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma. Les éléments rares sont restés dans le liquide résiduel jusqu'à ce que les conditions favorables à leur précipitation soient atteintes.L'établissement de ce lien génétique ouvre des voies pour des nouvelles stratégies d'exploration."

Jan 1, 2005

By D. Shishin

Continuous integrated experimental and thermodynamic modelling work is conducted in Pyrometallurgy Innovation Center (PYROSEARCH). The target is to develop a tool, which is capable to predict the compositions of phases, phase equilibria and enthalpy balance for pyrometallugical processes with higher accuracy. All these can be achieved by thermodynamic calculations based on Gibbs energy minimization algorithm. Recent developments made it possible to predict important factors, such as the chemical solubility of Cu in slag as a function of matte grade, temperature, P(SO2), Fe/SiO2 ratio in slag, wt% Al2O3, CaO and MgO in slag. In industrial practice, it is not only chemical solubility, but the overall amount of slag, which affects the recovery of copper and other valuable metals. It will also impact the energy balance. The presence of solids in the slag matrix influences the physical entrainment of matte in slag. Oxygen enrichment which is sometimes used to control the temperature of the furnace, may also affect the volatilization of minor elements into the gas phase. Same is true if additional fuel is used to compensate for heat balance. In other words, all key process parameters mentioned above are interrelated. Present study demonstrates the ways thermodynamic modelling can be used to link those process parameters on the example of copper smelting. INTRODUCTION Research methodology involving integrated thermodynamic modelling and experimental approach has been recently reported by the authors (Shishin, Hayes, & Jak, 2018 Shishin, Hidayat, Jak, Decterov, & Belov, 2016). Present paper reviews the updates and discusses challenges in the development of a large self- consistent thermodynamic database. The database covers the Al-Ca-Cu-Fe-Mg-O-Pb-S-Si-Zn-(Ag, As, Au, Bi, Ni, Sb, Sn) chemical system. The database works in the environment of FactSage software Bale et al., 2016 and related family of products: ChemApp (Petersen & Hack, 2007), ChemSheet and SimuSage. A list of phases, and thermodynamic models is shown in Table 1. For the copper industry, most important phases are Gas, Slag, Spinel and Liquid matte/metal/speiss. Black-colored elements represent the base system, elements in green can be considered as slag modifiers (slagging elements), and elements in red are minor. Ni is highlighted because it was included recently, in 2019, and currently under development. In addition to copper, the database covers the conditions typical for lead and zinc pyrometallurgical extraction. It is developed in consistency with the experimental results for high concentrations of Pb and Zn. Examples of applications in the present study include the thermodynamic analysis of fluxing for an agitated copper reactor to show the effect of Fe/SiO2, and calculations of copper slag cleaning using reductant.

Jan 1, 2019

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By A. C. de Araujo, M. G. Barbosa, R. Martino, S. Gaydardzhiev

The Iron Quadrangle district is a world-class iron ore mining district in the region of Belo Horizonte, capital of Minas Gerais state, in Brazil. Many mining companies have been mining high-grade hematite ores for decades throughout the region. The mines reserves often include itabirite ores which are available in high volumes, but have lower iron grades than hematite ores and require elaborated mineral processing to meet the requirements of downstream steelmaking. Itabirite ores have acquired importance, with the depletion of high-grade hematite reserves due to their intensive mining. The objective of this paper is to propose a geometallurgical model for the processing of itabirite ores from an Iron Quadrangle deposit, which will allow predicting the behaviour of ores throughout the deposit, according to their local variations. An initial step consists in characterizing representative samples of the different ores to acquire mineralogical and textural data. Then, itabirite ores of known characteristics are processed with different techniques, in order to extract the trends and key parameters upon which the geometallurgical model is developed. At first, the model takes into account the particle size distribution and its shift during mining and screening, as well as the chemistry and mineralogy of the material. Then, using the previously identified key parameters such as iron recovery, the model predicts the composition of the processing products. Finally, this data is used to model the mineralogy and mass recovery of the products. The geometallurgical model is of great importance, as it is able to model the processing of any sampled ore throughout the deposit. The incorporation of the results in a mining block model will assist mine planning and opens new opportunities for an optimized mining schedule.

Jan 1, 2016

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By Yong Kang, Bingyuan Yan, Dandan Zheng, Xiaochuan Wang, Dengfeng Su, Dongyang Li

"According to the characteristics of rock mass and the directional cutting technology of water jet, a new idea of light shock controlled blasting with water jet slotting was put forward. Based on the fracture mechanics theory and the stress wave theory, the mechanism of damping with water jet slotting was analyzed. On the basis of the above, the evolution law of the pressure wave and displacement field during the blasting were simulated by FEM software ANSYS/LS-DYNA. The result shows that: the oriented slot plays a good role in orientation during the blasting, and makes the energy generated by gas released by the explosives gather at the tip of the oriented slot, which makes it easier for the main crack to expand along the oriented slot and indirectly reduce the stress effect on the protected object. Meanwhile, the energy of the seismic wave is reduced while transmitting through damping slot. Finally, compared with the normal blasting with damping ditch, the maximum acceleration is reduced by 15.62%, the maximum velocity is reduced by 52.99%, and the maximum displacement is reduced by 68.32%. INTRODUCTIONIn recent years, with increasing demand for energy and space, an increasing number of underground projects have been under construction. Drilling-blasting method, as a traditional main method for rock excavation, is still an indispensable means in the engineering construction. As is known, blasting vibration will cause the deformation and unstable of the existing building structures, so how to reduce the influence on the existing building structures caused by the blasting vibration has become the focus. Traditional shock absorption measures mainly include three kinds: the first one is pre-splitting blasting, the second measure is to change the parameter of explosive filling, and the last one is to excavate damping ditch between the protected object and blastholes. However, engineering practices show that: the protected rock may be damaged in the process of pre-splitting crack construction by blasting, the second measure is difficult in operating, and the third measure is troubled by large work quantity (Song Guangming, 1999; Lou Jianwu, 2004; Lou Jianwu, 2005; Li Xibing et al., 2008)."

Jan 1, 2015

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019