Search Documents

By Jing Chai

The Cenozoic unconsolidated strata with the thickness of 100 to 240m in the east area of China are composed of clay, sandy clay and hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged to various degrees since 1987, with the main reason for this being the subsidence of the super-thick unconsolidated strata. To prevent the continuing settlement deformation of unconsolidated strata caused by groundwater removal, long-term water injection through multiple boreholes controlled the settlement deformation of unconsolidated strata. A new type of fiber Bragg grating (FBG) sensing system was successfully used for real-time strain monitoring of the unconsolidated strata during water injection at a coal mine in China. A mathematical model for the compression settlement induced strain calculation is proposed which can assist understanding of the effect of water injection on the ground. With the increase in water injection, the unconsolidated strata compressed state was improved by the transition of the stress state from compressive to tensile stress. The wavelength change of fiber Bragg grating sensors corresponded with the trend of the water level in the same strata. Engineering practice indicates that these sensors can normally, safely and reliably survive conditions associated with hydrous unconsolidated strata. The FBG sensing can be used for continuous lifetime monitoring of the system, starting with real-time monitoring during low-pressure water injection process of multi-borehole. The results will give important guidance for water injection and mastering stratum subsidence.

Aug 1, 2013

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By S. Jain

Construction industry is considered as labour intensive, having shortage of skilled labour, unsafe with large number of industrial accidents. Construction industry requires high technology automation products (Robots) for improving productivity, safety, quality etc. Robots are developed by various countries in different areas like demolition, earthwork, bridge, tunnels, road work, underwater works, trenches and piping, maintenance etc. however they are still not used to their full potential by construction industry. Hence in this paper, the authors propose a ?model for adoption? of robots in construction industry. This model considers how a construction firm will adopt full scale robots like manually controlled machine, tele-controlled machines, computer controlled machines and cognitive robots and assimilate them through various stages.

Aug 1, 2013

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By Ralph W. Edie

"IntroductionTHIS PAPER presents some analyses of diabases from a number of metallogenic provinces in Canada and the United States. It is intended as a contribution to the literature on the genesis of mineral deposits associated with diabase.As it has been in the past, opinion today on the origin of the cobaltnickel- native silver and associated pitchblende type of deposit is sharply divided. Some geologists hold that this type of deposit is in some way genetically related to intrusive diabase; others are of the opinion that the deposits are related to granite. The controversy, like others of a similar nature, probably will not be settled satisfactorily for many years to come, •but in the meantime it is recognized that, with respect to most deposits of the type referred to, altogether too few facts are known for accurate conclusions on genesis to be drawn. To contribute in a small way to factual data on this whole .problem, the writer analyzed diabase from several districts in Canada in which deposits of the aforementioned type occur. For comparative purposes, the copper, cobalt, and nickel content of diabase from Cornwall, Pennsylvania, and of norite from the Sudbury basin of Ontario, was also determined.Insofar as is known, none of the analytical work undertaken had been previously carried out."

Jan 1, 1953

By John Redstone, André R. Laplante

"Le rebroyage des concentrés d'hématite en usine (Sidbec-Normines, Port-Cartier) et en laboratoire a été modélisé selon le modèle de Reid (1965).L'effet du pourcentage solide sur la cinétique de broyage a été étudié en usine. La fonction de sélection corrigée (pour tenir compte de l'effet du pourcentage solide sur le temps de rétention) augmente lorsque le pourcentage solide augmente de 80 à 84 pourcent. Cette amélioration est contrebalancée par une augmentation de la quantité de pulpe court-circuitée, à des pourcentages solides supérieurs a 81%. La densité optimum de broyage se situe à 84 pourcent.Comme alternative au mode d'opération actuel, l'assemblage des broyeurs en série plutôt qu'en parallèle a également été simulée. Le moins 44 µm passe alors de 68.1 à 72.5 pourcent, ce qui correspond à une capacité supplémentaire de 32 tonnes à l'heure par broyeur. Ces résultats doivent toutefois être interprétés avec prudence, car la cinétique de broyage n'est généralement pas linéaire lorsque le taux d'alimentation est plus que doublé.IntroductionL'usine de bouletage de Sidbec-Normines Inc. a été décrite par Morimoto (1977), Lévesque et al. (1979) et Pabst (1979). La section de broyage des concentrés contient six broyeurs à boulets en parallèle et en circuit ouvert, d'un diamètre de 5. 18 mètres et de 10.36 mètres de longueur. Ils contiennent chacun environ 350 tonnes de boulets d'acier forgé de 3.8 cm de diamètre. Le concentré est broyé de 10 pourcent moins 150 µm (100 mailles) à 65-68 pourcent moins 44 µm (325 mailles), à un pourcentage solide de 78 à 80 pourcent. Cette fragmentation poussée exige une consommation d'énergie de 32 kWh/tonne. Cette énergie est surtout libérée sous forme de chaleur, la pulpe étant déchargée a une température de 68-72° C. II en résulte un milieu de broyage corrosif, et une consommation de boulets élevée, de 3.4 à 4.0 kg / tonne broyée."

Jan 1, 1983

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By M. M. C. Lima, L. C. S. Solimani, M. A. Quintela

Galvanized steel scrap is recycled to B OF converters where zinc escapes from the bath and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contain high iron content, it could be recycled, but due to its zinc content, it is disposed in landfills. In this study techniques were evaluated for zinc layer removal from scrap by sulfuric acid leaching. The effects of coating weight, temperature, time and sulfuric acid concentration were evaluated for three different galvanized scrap. The results showed that the behavior of each galvanized scrap was different. Nevertheless zinc removal efficiency was more than 80% with low dissolved iron in the leached solution.

Jan 1, 2011

By F. Azgomi

A possible way to characterize (classify) frothers using gas holdup as a surrogate for bubble size was explored. Nine surfactants with a range in chemical structures were selected and tested in a bubble column instrumented to measure gas holdup and superficial gas velocity. A correlation between frother type and gas holdup was observed: for alcohols, gas holdup increases with hydrocarbon chain length and the effect is the same whether the chain is branched or straight; for polyglycols, gas holdup increased with number of propoxy groups. The ranking by gas holdup gave the same result as other frother characterization techniques.

Jan 1, 2006

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By C. Tasker

Introduction In the Early part of 1930 the Ontario Research Foundation was asked by the Minister of Mines, the Hon. Charles McCrea, K.C., M.P.P., to undertake a technical and economic investigation of the Northern Ontario lignite deposit. This investigation has been under way since June, 1930, and has necessitated considerable work at the deposit, in the laboratories of the Foundation, and at test plants in Europe. All the work has been carried out in active co-operation with the Provincial Department of Mines, the Deputy Minister, Mr. T. F. Sutherland, and several of his technical colleagues being associated with members of the staff of the Foundation on the Advisory Committee, which has met at frequent intervals to co-ordinate and direct the various lines of research. An interim report was made to the Minister of Mines by the Director of the Foundation, Dr. H. B. Speakman, at the end of December, 1932, and is at present under consideration by the Minister. This report deals with the extent and character of the deposit, the methods and costs of mining, and the methods and costs of processing raw lignite, the characteristics of certain lignite products, and the technology and economics of present fuel utilization by railways, industry, and domestic users in northern Ontario. It is not the purpose of the author to discuss in this paper either the geology of the deposit or the economics of the mining, processing, and utilization of lignite, but rather to deal briefly with some of the technical problems investigated by the Foundation during the study of the characteristics and methods of utilization of Northern Ontario lignite. Some mention, however, of the work carried out to define the extent of the deposit is a prerequisite to any discussion of the nature of the lignite.

Jan 1, 1933

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By S. A. Bradford

The twenty years before World War I was the Golden Age of copper smelting in British Columbia. In this short time, the smelters developed from small, primitive units to large, efficient operations. The first copper claims had been staked on Howe Sound and Knight Inlet in 1864, and there was extensive copper mining in the interior by the mid-1880s, but before 1895, all ore was shipped out of the country for smelting, converting and refining. The first interest in smelter construction was undoubtedly inspired by a Provincial bonus and Dominion land grants offered to smelter builders. The early smelters made use of small blast furnaces which were designed to smelt any kind of ore, but usually far too little ore was available. The first smelter seems to have been the McRae furnace on the Spillimacheen River (1883), followed by Vancouver (1889), Revelstoke (1891), and Golden (1891) (1). They each smelted a few tons of galena and then quickly closed down permanently for lack of ore. Only smelters that actually produced some copper matte are described in the following sections.

Jan 1, 1999

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By J. A. Finch

For base metal sulphides, iron rejection starts in mineral processing. This review focuses on the changes in plant practice specifically to improve iron sulphide rejection by controlling contaminant ion effects and discusses selected innovations in mineral processing that can be expected to play a role in iron control. One change to control contaminant ions is size reduction (the use of stage grinding and inert stirred milling) and another is system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy species). Plant examples illustrate the successes, and indicate that there are several options available. The general innovations consider the new tools for measuring gas dispersion properties and quantifying froth characteristics from images. Examples of their application to improve concentrate quality illustrate the potential. Other innovations adapt geostatistics to model variations in ore flotation response to provide feed forward control and rigorously apply the statistical experimental methodology in plant test work. An example from one concentrator shows that significant improvements to reduce the iron content of concentrates can be achieved by applying these basic principles.

Jan 1, 2006