Search Documents

By H Zorychta

Based on underground measurements made at the Nova Scotia coal mines of the Dominion Coal Company, Limited, this paper presents a comparison between the physical properties of hardwood packs and steel friction props when used for longwall support. The probable loads sup-ported by steel friction props on a longwall face at both the Dominion No. 20 Colliery and the Princess Colliery are delineated, and the results of the tests are presented in graphical form. It is concluded that the steel friction props are more efficient than the hardwood packs that they replaced as roof supports. Introduction AN evolution in the methods of longwall face support is taking place in the Sydney coalfield. Longwall face support had consisted primarily of timber props and hardwood packs. In 1957, however, at the Princess Colliery, Sydney Mines, Nova Scotia, the first longwall was equipped with steel friction props. At the present time, eleven longwall faces are supported on wood and sixteen faces are carried on steel friction props.

Jan 1, 1965

By Bertrand Robinson

Great advances have been made in rubber-lined pumps for the pumping of mill pulps. The Canadian Allis Chalmers alone report ov.er 300 such pumps put into service during the past four years. Pumps in which both the casing and the impeller are rubber covered have proved most economical in handling the usual run of mill pulps, effecting large savings in power, maintenance, and shutdown costs. For the handling of pulps containing comparatively large, sharper edged /articles, rubber-lined casings with hard iron impellers have been developed by the pumping departments of Hollinger and Noranda. These rubber-iron combination pumps show an appreciable reduction in overall pumping costs as compared with the all-rubber and the all-iron pumps. The power efficiency is lower in rubber-iron than in all-rubber pumps but higher than in the all-iron pumps, with lower replacement costs due to the cheap iron impellers used. Where continuous operation is essential, however, and duplication of units to take care of shutdown time for replacement of parts is not within the expenditure budget of the company, all-rubber pumps are being used t0 a greater extent. As in all items pertaining to milling operations, the economics of the situation must be studied as closely as the technical details, to arrive at the most advisable practice.

Jan 1, 1939

By M. E. Holuszko

Although there is no widely accepted rigorous definition of handleability, the handling coal characteristics often referred to as handleability define whether a coal has the ability to flow unhindered through the processing and transportation systems. The handleability may be severely affected if fine coal particles tend to aggregate. In the pelletization process, the rolling action of the drum is applied to bring the individual particles into proximity with each other so that they can aggregate and form pellets. Because of apparent similarities between these two processes, the pelletization tests are carried out in parallel to the handleability tests in this project, and the pelletization results are used to explain coal handleability properties.

Jan 1, 2004

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By J. C. Folinsbee, D. R. Derry

"The Property of Opemiska Copper Mines (Quebec) Ltd. is in Levy Township, Chibougamau district, west of Chibougamau and south of Opemiska Lake. The original find was made in 1929 by the late Leo Springer and associates of Prospectors Airways Ltd., following observation from the air of an area of dark rocks in newly burned-over country. Work on the ground discovered three veins of high-grade chalcopyrite in gabbro (No. l, No. 2, and ""North"") and, after several seasons of trenching and diamond drilling, financed by Ventures Ltd., a shaft was sunk in 1936. This work indicated about 280,000 tons of six per cent copper ore to a depth of 500 feet. During this period, the senior author carried out a reconnaissance geological survey over the whole property and surrounding claims, which showed that the veins were in the gabbro portion of a large composite basic sill that had been folded with the enclosing lavas. Owing to the low price of copper and lack of transport work was suspended and the property remained dormant until 1951.In that year the company was re-financed, the property prepared for production, and further exploratory drilling undertaken. The drilling, based on structural indications, located a new vein of which the only previous evidence had been some irregular stringers. This vein, No. 3, was traced by drilling for a length of 2,000 feet and the indicated reserves were thereby increased to about one million tons. An additional vein, No. 4, was intersected in several holes.With this encouragement, plans for production were confirmed, and operations commenced' at the beginning of 1954 on a scale of about 400 tons a day, concentrates being shipped by truck to St. Felicien and thence by rail to Noranda. In the first year of operation concentrates were re-covered carrying 14,047,210 pounds of copper, 76,714 ounces of silver, and 6,259 ounces of gold. The operation is under the direction of J. P. Millenbach, General Manager, with J. M. Thompson as Assistant General Manager and F. G. Cooke as General Superintendent on the property."

Jan 1, 1949

By Joël P. T. Kapusta, Liam J. Watt

The last extended copper smelting and converting survey dates back to the 2003 International Copper Conference held in Santiago, Chile. The following year, the Minerals, Metals, and Materials Society of AIME (TMS) started a new series in its Journal of Metals (JOM) called JOM World Nonferrous Smelters Survey devoting its first Part to Copper. The copper smelting landscape has significantly changed in the past 15 years, both in geographical terms with the shift of copper smelting production from the Americas to China and in technological terms with the growing adoption rate of Top-Submerged Lancing (TSL) technologies and the development and implementation of Bottom-Blowing technologies. A copper smelting survey update, even if not as in-depth as the 2003 Copper Smelting Survey, is therefore in order. The authors will review the latest trends in copper smelting technologies and production worldwide in comparison to the landscape of the early 2000s. INTRODUCTION This 2019 copper smelting survey is different from previous surveys as our data does not originate exclusively from responses to a questionnaire sent to all the copper smelters. Our data comes from several sources. We are therefore very thankful to the International Copper Study Group (ICSG) and Wood Mackenzie for sharing some of their information and to ENFI, Outotec, and Glencore Technologies for helping us cross-check our numbers for the Chinese smelters, flash smelting, Ausmelt, and Isasmelt technologies. Our survey presents data reporting from a total of 96 operating copper smelters from around the globe, which is significantly higher than the 50 surveyed in 2003. Although secondary smelting numbers have steadily increased over time, this paper focuses on primary smelting operations with copper concentrate as feed material. The list in this survey is still far from complete, with missing information from several known smelting operations. The total primary copper production tonnage of the smelters we surveyed amounts to 18.3 million metric tonnes from 29 countries representing 92% and 94% of total world primary production for 2018 estimated by ICSG and Wood Mackenzie, respectively. This representation has increased from 2003 when the total was 9.71 million metric tonnes from 23 countries accounting for 73% of world production. The trends presented and analyzed within this paper have stronger significance because of the increase in production accounted for. The Chinese and Russian smelter information collected is more detailed than years past. Our complete dataset is summarized in Table 1 at the end of our paper.

Jan 1, 2019

By M. Vaillé, B. Bossé, N. Durupt, A. Michaut

Imouraren is a sedimentary uranium deposit (> 150,000 tU @ 800 ppm), located approximately 100 km North-Northwest of Agadez (Niger); its depth reaches 110 to 170 meters. For low-grades ores, heap leaching is commonly considered as the appropriate technology for metal recovery. More precisely, the ore is crushed (≤ 300 mm) and agglomerated before being stacked. In this case, sulfuric acid can be added during agglomeration and/or irrigation (for three months to a year) to improve uranium recovery. It is known that mineralogical, chemical and physical properties of the uranium ore impact recovery, yet many challenges remain to increase recovery using this process. For example, ore heterogeneity and spatial variability (e.g., variation in uranium, carbonate and/or clay contents) can affect heap leaching performances (i.e., metal recovery, acid consumption or neutralization, percolation rate). However, laboratory column tests using composite ore sample that do not consider ore heterogeneity are widely used to anticipate recovery. Consequently, a new approach that consists in using Imouraren drill core ore samples was recently investigated. This latter also enabled a better assessment of the main parameters that influence uranium recovery and proposed a new predictive model to optimize mining operations.

Jan 1, 2020

By Kéiko H. Hattori, Neil T. Pettigrew

"Abstract- The Legris Lake Complex is a northeast-trending, 7.3 km long by 3.5 km wide, maficultramafic intrusive complex located in the western Wabigoon Subprovince of the Archean Superior Province. It is one of a series of mafic-ultramafic igneous complexes, the most notable of which is the Lac des Iles Complex, host to Canada’s only producing Pd mine with reserves of 93.5 Mt grading 1.53 g/t Pd as of December 2001 (North American Palladium Ltd., Annual Report 2001). Cu-Ni- PGE mineralization was first discovered in the Legris Lake Complex by a local prospector late in 1999. Shortly thereafter, the property was jointly optioned by Avalon Ventures Ltd. and Starcore Resources Ltd., who continue to discover significant Cu-Ni-PGE mineralization.One of the most notable features of the Legris Lake Complex is the occurrence of extensive brecciation caused by multiple injections of volatile-rich magma. The Cu-Ni-PGE mineralization is hosted by leucogabbro within a 2 km long by 600 m wide, highly brecciated area in the northwestern area of the Complex. The mineralized rocks contain disseminated to blebby sulfides (1 to 5 vol.%), comprising chalcopyrite + pyrite ± pyrrhotite + millerite ± pentlandite, typically surrounded by epidote. The majority of the Cu-Ni-PGE mineralization displays low ratios of Pt/Pd (~0.20) and high ratios of Cu/Ni (~2.9), which are similar to those of the Lac des Iles and the River Valley mafic-ultramafic complexes. The lithologies in Legris Lake Complex bear similarities to the heterolithic gabbro of the Twilight and Roby Zone deposits at the nearby Lac des Iles mine. However, the mineralization at Legris Lake, which is restricted to leucogabbro overlying unmineralized clinopyroxenite, is similar to that of stratiform deposits such as the Stillwater and Munni Munni complexes. The mineralization at Legris Lake is best explained by the late-stage, immiscible separation of a sulfide melt from volatile-rich parental magmas and the subsequent minor redistribution of metals by deuteric fluids."

Jan 1, 2001

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By F. Hashiuchi

In 1996, the Saganoseki custom smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity, especially in the area of P.S. converters and acid plant. As the results of modifications and operational improvements, the gas washing & cooling sections of the Saganoseki acid plant were consolidated from 3 to 2 lines, and increased the gas treatment capacity. The S02 converters in the acid plant were also modified to increase the acid production. By increasing the matte grade from 65 to 68%, six PS converters have been successfully integrated into four, while maintaining the production capacity and reducing the environmental burden in 2005. This paper discusses recent operational conditions and the results of implementation of technological improvements.

Jan 1, 2007

By M. A. F. Fedikow, D. A. Baldwin, C. Taylor

The Agassiz Metallotect and the Johnson Shear Zone represent two metallogenetic fea tures located within the northern and outhern belts, respectively. of the Aphebian-aged Lynn Lake greenstone belt in northern Manitoba . Numerous gold occu rrences are associated with these two regional features . The tratabound Agas iz Au-Ag deposit with 2.9 million tonnes of 5.2 g/tonne Au and 11.8 g/tonne Ag. occurs within the Agassiz Metallotect. The stratigraphic sequence characterizing the Agassiz Metallotect comprises interlayered ox ide. silicate and sulphide facies iron formations, biotite-rich and siliceous siltstones. and a high Mg- i-Cr basaltic rock that ha previou ly been identified as tholei itic picrite. These rocks can be traced in outcrop and by their INPUT and gradiometric signature for 65 km. The Johnson Shear Zone is an ill-defined 35 km long zone of strucwral disruption that crosscuts volcanic. sedimentary and intrusive rocks and contains numerous vein-type gold occurrences. Both of these metallotects are characterized by their low level of exploration activity and as a result offer excellent residual exploration potential. Rock, basal till and vegetation geochemical techniques applied in the vicinity of the Agassiz deposit indicate the presence of trace element dispersion halos associated with the mineralization. The halos define an exploration target larger than the mineralized zone. Gold occurrences within the two metallotects are described with emphasis on the Agassiz Au-Ag deposit . A wide range of gold occurrence-types is documented including syngencticstratabound , epigenetic-replacement and epigenetic-quartz vein .

Jan 1, 1986

By B. E. Halbert, K. T. Himbeault, S. L. Fernandes, R. L. J. Phillips, B. J. Topp

The Beaverlodge uranium mining and milling facilities operated from 1952 to 1981 with about 94% of the ore extracted from the main underground mine and 6% from smaller satellite deposits. Decommissioning work occurred from 1982 to 1985 involving periods of shutdown, salvage and reclamation. Transition phase monitoring, leading to eventual delicencing commenced in July 1985. Over the last 15 years, discharge from the tailings management facility (TMF) and a fresh water stream, impacted during the operational phase by tailings spills, has improved in water quality for most parameters of concern. Loadings to the environment of three key contaminants (radium-226, total dissolved solids, and uranium) have consistently been less than during the operational phase with radium-226 having the greatest variability. Outstanding environmental issues associated with the recovering drainage system formerly used for tailings disposal, are being addressed in an enhanced environmental monitoring program to commence in 2000. Changes in water chemistry and the natural re-introduction of aquatic organisms are issues of concern. In the meantime, application for release from selected satellite areas commenced in 1999. This paper reviews the issues which have arisen during the transition phase, outlines how they have and are being addressed, and provides a comparison of original and current predictions of the recovery process under way at the former Beaverlodge mine site.

Jan 1, 2000

By Howard J. Handewith

"Tunnel boring machines have been tried in underground mining applications as early as 1957. Although tunneling machines hardly threaten to supplant traditional drill-blast-muck operations for drifting, the latest modern machines offer substantial improvements in progress rates over traditional methods under certain conditions.An evaluation guide is offered which identifies conditions that favour machine boring. Different types of costs related to the use of a tunnel machine are discussed. The advantages of the tunnel machine over the traditional method are reviewed. IntroductionThe first tunnel boring machine ever used in a mine was in Quebec in the year 1957. Although less than successful at the time, this experiment served to illustrate the mining industry' s willingness to try new ideas. Since 1957, the manufacture of tunnel boring machines has developed into a full-size industry. Most contractors in Europe and North America will now consider the use of a tunnel boring machine first on any long tunnel that can have a circular section.The modern tunneling machine offers a great potential to the mining industry. Just as the blasthole and raise drill machines have revolutionized mining in the last decade, it is expected that tunnel boring machines will make an equal impact in the future.This is not to suggest that tunnel boring machines will replace explosives in the foreseeable future, but they can supplement drill-and-blast operations. In areas where long drifts, inclines, declines or cross-cuts are needed in a hurry, the tunnel boring machines offer the fastest way to a production return on investment. Figure 1 shows the range of production that two types of tunnel machines have produced as compared with conventional excavation methods in various ground conditions.Rotary hard-rock tunnel boring machines (Fig. 2) commonly produce progress rates in excess of 20 metres per day in uniform ground from 300 to over 2,000 kgl cm2 in unconfined compression strength . These averages are for the completed tunnels. One 7. I6-metre-diameter tunnel boring machine just completed a 1O.7-km tunnel in hard rock of 700 to 2,800 kg/cm>, The last eight months of production averaged 30 metres per day."

Jan 1, 1980

By J. F. J. Thomas

"AbstractBoth the quantity and quality of waters available as raw materials are important to Canadian industry and to the national economy. The huge demands of many Canadian industries is illustrated by tabulated figures, based on the 1950 Canadian production of certain products, and on United States figures for the gallons of water required to produce a unit quantity of each product. It is suggested from comparison with American survey results and figures that Canadian industrial water consumption is 1 to 11/2 billion Imperial gallons per day. Since present information on Canadian usage is meagre and it is not certain that American survey results can be directly applied to Canadian industry, this estimate must await confirmation in future studies.The hydrologic cycle and the principal factors affecting the quantity and quality of water, namely, climate and season, topography, geology, vegetation, and human activities, are discussed and the principal salts dissolved in water which affect industrial use are enumerated.The present survey studies by the Mines Branch on water quality are outlined. Besides chemical analyses of municipal water supplies within a watershed, periodic sampling and analyses of major surface waters for a one-year period is being carried out. The importance of studies on seasonal variation in quality is stressed by comparing the dissolved salts in various river waters with river flow. Figures showing such relationships in the Rideau river and Ottawa river at Ottawa, the Columbia river at Trail, B.C., and the Battle river at Unwin, Sask., are presented. Different rivers show different quality changes with changing flow, and possibly only after long-term studies can the relationships be predicted.Quality studies on water may be as important as studies on many other raw materials. The quantity of the raw material, water, is not inexhaustible nor is the quality indestructible, and more realization of its importance, followed by conservation and intelligent use, is desirable."

Jan 1, 1952

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By C. Carrasco

Caletones Smelter, Division El Teniente of Codelco Chile, has used Teniente Converter (TC) as the only smelting unit since November 2000. The modernization project considered the shutdown of the last reverberatory furnace, the installation of the fourth Teniente Slag Cleaning Furnace, the installation of a new fluidized bed dryer and the modification of the concentrate injection system into TC. The modernization project and related investments allowed for the increase of the smelting capacity up to 1.25 million t of concentrate annually.Next stage of the smelter expansion in the year 2004 considered the increase of the smelting capacity up to 1.44 million t/year. The expansion required technology modernization and the installation of the new equipment, such as concentrate injection system, oxygen plant, fluidized bed dryer and storage bin. Currently the annual smelting capacity is about 1.35 million t of copper concentrate, being limited by sulphuric acid plant treatment capacity. This paper presents the technology and production evolution in the Caletones Smelter in the years 2000 - 2006, demonstrating the potential of development and competitiveness of Teniente Converter as world-wide recognized smelting/converting reactor.

Jan 1, 2007

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda's history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016