Search Documents

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper' the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

By R. Prioul, J. Kear, D. Chuprakov, A. P. Bunger

"Hydraulic fracture (HF) growth through naturally fractured rocks challenges the development of accurate predictive HF models. The authors present laboratory experiments differentiating behaviours associated with orthogonal and oblique intersections between HFs and natural fractures (NFs). HFs were created in sandstone and crystalline (gabbro) rock specimens, impinging orthogonally or obliquely on an unbonded machined frictional interface. Ultrasound monitoring was used to observe the rate of propagation through the interface. A contrast was observed between direct and offset crossing for orthogonal and oblique intersection, respectively. The stresses required to promote crossing depended on the intersection angle between HFs and NFs.RÉSUMÉ La propagation des fractures hydrauliques (FH) dans les roches naturellement fracturées pose un défi pour le développement de modèles prédictifs. Nous présentons des essais en laboratoire qui différencient les comportements associés aux intersections orthogonales et obliques entre les FH et les fractures naturelles. Des FH ont été créées dans des spécimens de grès et de roches cristallines (gabbro), heurtés de manière orthogonale ou oblique sur une interface machinée, non liée, de frottement. Un suivi par ultrasons a servi à observer le taux de propagation à travers l’interface. Un contraste a été observé entre un croisement direct et un croisement indirect des intersections respectivement orthogonales et obliques. Les contraintes requises pour promouvoir le croisement variaient selon l’angle d’intersection entre les FH et les fractures naturelles."

Jan 1, 2016

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By Stéphane Robert

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributable to accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company's total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company's historical results of operations is set forth in the notes to the financial statements included in the Company's Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By D. Lunt

Telfer bulk concentrates typically contain 8% chalcopyrite, 8% chalcocite, 45% pyrite and 80-120 g/t gold. Although very high copper and gold recoveries can be obtained by subjecting the concentrate to a "conventional" high temperature pressure oxidation step followed by copper recovery by solvent extraction and electrowinning, and cyanidation of the leach residue for gold recovery, the cost of lime required for neutralisation and power for oxygen generation was such that the process was uneconomic in terms of operating costs. The challenge therefore was to develop an alternative flowsheet that maximised copper and gold recovery in which the reagent costs were commercially attractive. An additional objective was to reduce the capital cost so that the overall NPV and IRR values would enhance the economic viability of the total project. Following a series of batch and locked cycle testwork programs, supported by Metsim modelling, it was established that the same high levels of overall copper and gold recoveries can be obtained by use of a novel two-stage split leaching circuit in which the chalcocite component is leached in a low temperature (90-110°C) circuit with the chalcopyrite component treated in a high temperature (220-250°C) circuit. This split circuit has a number of advantages, including minimising the required capacity of the high temperature autoclave, as well as reducing the overall lime consumption and simplifying the total process water balance. The paper outlines the basis for the development of the flowsheet and discusses the integration of the leaching stages into the overall circuit.

Jan 1, 2004

By W. Harry Foster

"Asbestos Corporation Limited, incorporated in 1925, operates four asbestos mines and three asbestos mills in the Thetford Mines 1•egion of Quebec's Eastern Townships. A unique asbestos orebody, located in the Ungava Peninsula of Nouveau Quebec, was purchased by Asbestos Corporation Limited in 1964 and commenced production in 1972. As there were no existing facilities in the isolated, arctic region of Asbestos Hill, it was necessary for Asbestos Corporation Limited to construct at Deception Bay a deepsea wharf, a large ungraded fibre shed, a power plant and camp facilities. Forty-two miles of road were needed and were constructed from Deception Bay to Asbestos Hill. At Asbestos Hill, a complete crushing-drying-milling complex, a power plant, pe1•sonnel accommodations and open-pit facilities were provided. Unloading facilities and a fib1•e finishing mill we1l constructed at Nordenham, West Germany. The ""Asbestos Hill- Nordenham Story” is divided into individual papers covering all aspects of the engineering, construction and operation of this unique enterprise. Particular emphasis has been placed on those unusual aspects caused by the isolated location, arctic conditions, short shipping season and the deep permafrost."

Jan 1, 1976

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By William B. Coker, Vladimir J. Sopuck, J. S. Fox

"Preliminary investigations indicate that organic lake sediments offer some potential for gold exploration within the Canadian Shield of northwestern Saskatchewan. It is also apparent that certain precautions must be taken.Gold is primarily related to the organic fraction of the lake sediments, which, although giving consistant Au contents to those sediments, may restrict the dispersion of Au within the lake itself. It may be necessary to carry out selective extractions on the lake sediments to differentiate between Au related to organic sequestration, indicative of hydromorphic and/ or chemical dispersion, and Au related to inorganics, indicative of mechanical dispersion.Lake sediments are probably only of use for very detailed exploration (i.e. every lake). One to three samples per lake should be appropriate, although a single centre-lake organic-rich sediment sample may be adequate in very small lakes. Each lake sediment sample should be analyzed at least twice and the analytical data carefully monitored and evaluated.The use of As in lake sediments as a pathfinder element for gold is applicable in the search for certain types of gold occurrences.Following detailed lake sediment sampling, basal till sampling can possibly be used to localize areas of potential gold with or without base metal mineralization."

Jan 1, 1982

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By Yuki Tsunazawa, Shuji Owada, Sho Fukui, Chiharu Tokoro

"Since the amount of e-waste has been rapidly increasing all over the world, there is a desire to develop the effective recycling process. E-waste has various kinds of electronic components with valuable and/or hazardous materials. Recycling of them is an important subject from the viewpoint of both the recovery of valuable materials and waste treatment. In common with all mineral processing, the comminution of e-waste is a key process because the liberation states after comminution determine the overall efficiency of metal recovery. Since some of useful critical metals are concentrated in a specific component, a special and selective grinding is expected to be effective. However, the knowledge about the mechanism and the effectiveness of the selective grinding is still limited and unclear.To better comprehend the mechanism, in this study, the investigation of comminution process using the particle-based simulation was conducted. Especially, this study focused on the comminution performance of printed circuit boards (PCBs), which are major components of e-waste. The behavior of PCBs and airflow in a drum typed agitation mill having flexible chains was simulated by the discrete element method (DEM) coupled with computational fluid dynamics (CFD). To model the shape of PCBs, the particle based rigid body model was introduced into the DEM. Since this model could not directly simulate the breakage phenomena, collision energy was calculated to qualitatively evaluate the comminution performance. In addition, the simulation results were compared with the experimental comminution tests using simulant PCBs where some capacitors were solder-mounted. These results indicated that comminution performance was affected by the rotation speed of the agitator. It was also demonstrated that the comminution performance was qualitatively evaluated using the particle-based simulation and this particle-based simulation made it possible to investigate the mechanism of e-waste comminution."

Jan 1, 2016

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By P. J. Morgan, E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising’s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By H. J. McQueen

The modeling of the extrusion of 6061 alloy and its composites with 10 to 20 vol% Al203 or SiC by two techniques. The uniaxial finite element method FEM (DEFORM" ) provided force-stroke curves and temperature rise over the range 450-500 °C, 2.6-5mm/s and extrusion ratios of 31 and 64. The traditional technique considers ideal work and redundant work as well as friction and uses average temperatures and strain rates. The two techniques are used to clarify each other and to extend the analysis to 400 and 350 °C. The calculated efficiencies are compared to measured values in extrusion trials and to values derived for 7075 extrusion analyses. The analyses are based on constitutive equations determined by torsion testing tests.

Jan 1, 2004

By C. Dragusanu, J. Sims, J. Connolly

Based on a statistical analysis of the categorical and numerical data from the established geological model, a geochemical classification of mineralization has been shown to be objective in nature and correlated to the envisioned metal extraction process. Multivariate chemical classification has the potential to discriminate within a combined response from different types of alteration and metal abundances. Distinct domains of chemical response determined by clustering analysis were used as a validating criterion for a geologically driven metallurgical testing program. The groups established are spatially linked to the geological process responsible for their genesis, providing clarity in geometallurgical and resource modeling.

Jan 1, 2011