Search Documents

By Xiu-Xiang Tao

This study investigated bio-liquefaction of lignite and its model compounds of thymol, bezioc acid and quinoline by a fungus, Hypocrea lixii AH. It analyzed, during bio-liquefaction, enzyme activity of oxidase, LiP, Lac, MnP and polyphenol oxidase, and degradation products by UV-Vis, FTIR, 13C NMR and GC-MS. The results showed that the bio-liquefaction percentage (by mass) of lignite was up to 44.86 %. The bio-liquefaction products of lignite were mainly aniline, amide, ether, carboxylic acid ketone and ester. The aromatic ring number was 1-3 with an aromatic carbon ratio of 0.328, which indicated rings opening, bonds breaking and oxidation reaction. By considering with the enzyme activity analysis results, it showed that LiP and Lac catalyzed reactions to open aromatic cycles and to break bonds; esterase to break ester bond; and peroxidase in oxidation reaction.

Aug 1, 2013

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By Robert B. Parsons

"On August 8, 1989, the Minister of Finance released a technical paper which sets out many of the details of a proposed 9% federal value-added tax to be called the ""Goods and Services Tax"". The GST, which is scheduled to be implemented with effect from January 1, 1991, will affect all Canadians in different ways and to varying degrees. The mining industry itself should, by and large, benefit from the new tax.IntroductionOn January 1, 1991, it is proposed that the existing federal sales tax will be replaced by a new sales tax - the Goods and Services Tax (GST). GST will be leviedat a rate of 9% on most goods and services consumed in Canada.How it will WorkThe GST will be a tax on the final consumption of goods and services. It differs from a retail sales tax in that it will be collected throughout the production and distribution chain. However, the net effect of the tax paid on a particular good or service will be equivalent. The example above (next column) illustrates the application of the GST to the production and sale of a chair.Illustration of GST for a ChairEssentially, the total tax will equal 9% of the sale price to the final consumer. However, GST will be collected on the value added at each stage of the production and distribution chain . What will be TaxedVirtually all goods and services will be taxed. Items on which GST will not be charged fall into two categories: tax free and tax exempt."

Jan 1, 1989

By M. E. Bilir

In this paper, we review cases in which dramatic and visual swelling problems are experienced in underground structures. Swelling rocks have caused many problems in underground engineering projects. They pose severe problems to the design, construction and maintenance of underground openings. If an appropriate integrated design procedure, which proceeds from exploration, tests, analyses and realistic assumptions of swelling behavior, is used during the design stage, the execution of the project can be completed without any serious delays or dramatic design changes. The case histories were subdivided into three classes that include tunnels, underground coal mines and others. For the evaluation of cases, the surrounding rocks, swelling minerals, water inflow, swelling test results and swelling problems were considered. The main purpose of this review is to inform the reader about potential problems with swelling phenomenon and to emphasize the rehabilitation and extensive cost which are encountered due to the lack of necessary integrated design approaches.

Aug 1, 2013

By John A. Dresser

At a meeting of the Montreal Branch of this Institute in the autumn of 1928, the Honorable J. E. Perrault, Minister of Mines for Quebec, announced his intention to enlarge the Bureau of Mines of Quebec by the addition of a Division of Geology. The announcement further stated that the geological work proposed should be begun in the following field season, and that it should be on a substantial scale of not less than six field parties. The announcement was received with enthusiasm and much encouragement was held out for the success of the effort. It has been thought that the present meeting would be a suitable occasion to present a report of progress of this Division for the three years that have since elapsed. History This, of course, is not the first geological work to be undertaken by the Bureau of Mines. Prior to the establishment of the Division of Geology, the Bureau of Mines had not been unmindful of the need of geological research, but it had always lacked the means necessary to any sustained work. For more than 25 years the late J. Obalski was the Superintendent and the sole occupant of the Bureau. Yet, even then, Obalski, besides routine visits to mining districts, made a few exploratory trips along the north shore of the St. Lawrence river and one to Chibougamau, but without the equipment necessary to effective results.

Jan 1, 1932

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By R. D. Brown

Higher employer costs and increased employee benefits will result from the current sweeping revisions of the un-employment insurance system now receiving consideration before Parliament. The new legislation, the Un-employment Insurance Act, 1971, will substantially increase the unemployment insurance costs of many employers through an increase in the level of employer contributions -generally, employer contributions will go to 1.4 times employee costs -as well as by extending coverage to many classes of employees now exempt. Under the new legislation, executives, technicians, teachers, institutional workers and others will be covered, and eligible for the higher benefits which it provides. For the first time, absence from work because of illness or accident may qualify individuals for unemployment insurance benefits.

Jan 1, 1971

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By Stephen Mullowney

Outline ? Setting the stage ? Deal activity ? Q1 2013 update ? Key deal sectors ? Deals by geography ? Outlook for 2013 Key Observations 2012 ? Major retreat in M&A activity ? Glencore-Xstrata deal dwarfs all other deals ? Gold & copper dominate deal activity

May 1, 2013

By V. G. Papangelakis, A. Dani

"Alkaline pressure oxidation, particularly in the presence of trona as additive, can be used to oxidize high carbonate refractory gold ores as it prevents the formation of CO2 in the autoclave. However, the presence of silica in the ore can lead to the encapsulation of pyrite due to the solubility of silica in alkaline solutions and its subsequent reprecipitation on the reacting pyrite surface, leading to the formation of a passive layer. This fundamental study investigates the chemical composition and thickness of the passive layer on a rotating pyrite disk using XPS and SEM, as a function of process conditions at 230°C, in an aqueous slurry containing silica sand, sodium carbonate and calcium carbonate under 100 psi of oxygen overpressure.INTRODUCTIONAlkaline pressure oxidation (POX) has been used successfully to treat high carbonate refractory gold ores, which contain carbonates in addition to sulphides, most notably at Mercur and Goldstrike mines operated by Barrick Gold. There are several advantages to using alkaline POX over its acid counterpart, especially due to high carbonate content. First, it eliminates the production of CO2 in the autoclave without resorting to pre-acidification, which allows for high oxygen utilization. Second, alkaline POX suppresses the formation of elemental sulphur and intermediate sulphur oxyanions (such as thiosulphates and dithionates), which reduce gold recovery. Third, the use of sodium hydroxide or salts prevents the formation of anhydrite scale by forming soluble sodium sulphate. Other advantages are the use of cheaper materials of construction and the formation of non-acidic residue that do not require further treatment prior to cyanidation (Thomas, 2005).Sodium carbonate in particular is a promising reagent for alkaline POX because it was shown to significantly accelerate the kinetics of pyrite oxidation by molecular oxygen, when compared to other reagents such as sodium hydroxide, sodium borate and calcium hydroxide. This has been attributed to the following factors: a) the faster oxidation kinetics of Fe2+-CO3 complexes compared to Fe2+ oxidation, b) the buffering effect of carbonate ions on the acidic pyrite surface, and c) the increased solubility of oxidizing Fe(III) species due to carbonate complexation (Caldeira, 2010)."

Jan 1, 2012

By R. O. Burt

"IntroductionThe introduction to this section on gravity concentration indicated the wide range of equipment types that exist for the concentration of minerals, in what is the broadest size range of any concentration process.The equipment described in this chapter includes jigs, tables and sHme plant equipment. In contrast to the equipment described in the two succeeding chapters, this range of equipment, in nearly every instance, superimposes a mechanical movement on the fluid motion to effect separation of the valuable mineral from the waste mineral. The motion may be vertical Gigs), reversing (tables), or rotary (slime plants): however, in common they ""dilate"" the bed of particles to allow preferential settlement of the heavier particles.Description of Process UnitsJiggingJigging is the sorting of different minerals by stratification, based on the movement of a bed of particles relative to a fluid in a vertical plane.The basic construction of a jig is shown in Figure 1. Essentially it consists of an open tank filled with a fluid, normally water, with a horizontal jig screen at the top and with a spigot in the ""hutch"", or bottom compartment, for removal of heavies. The jig beri consists of a layer of coarse heavy particles (ragging) on the jig screen. This ragging is of a specific gravity between that of the minerals it is intended to separate.In operation the bed is made fluid by a pulsating current of fluid to provide stratification. On the upward or pulsion stroke the bed of ragging and slurry is normally Hfted as a mass, then as velocity of the upcurrent decreases it dilates, loosening the whole mass. On the downward or suction stroke it closes slowly again. The ideal is to control this dilation of the bed of material so that the heavier and smaller particles penetrate the interstices of the bed, while the larger heavies fall under a condition akin to ""hindered"" settling."

Jan 1, 1989

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By W. Rostoker

Packing Experiments The porosity and most of the other physical properties of a coherent mass of any material built up by the packing together of discrete particles will obviously vary with, and be governed by, the manner of association of the particles. The relation of packing to powder metallurgy has been discussed in some detail by at least two authors. Packing Theory Theories of particle packing have been put forward by C. C. Furnas and A. E. R. Westman. Although their approach to the problem is not the same, their conclusions are similar. In the process of packing, they visualize the voids of a uniformly sized material becoming filled with particles of a smaller size, and the voids between these being filled in turn with still finer particles. Obviously, if this process is carried ad infinitum, the resultant mass will have the same density as the constituent particles. In practice, of course, such a density of packing is never attained. In addition, the premise is made that successive particle sizes must fit into the voids left by the immediately larger particles- an assumption requiring definite size gradations and also particle shapes. It remained, then, for theory to correlate relative diameter ratios, and proportions and numbers of sizes of particles, for requisite packed densities. Briefly, the following principles were postulated: (a) For an infinite diameter ratio between largest and smallest sizes, an infinite number of particle sizes in proper proportion is required to give natural density. (b) For a given diameter ratio, there is a maximum number of permissible particle sizes for maximum packed density (Furnas). (c) Provided the particle shape is spherical, or approximately so, the proportions o particle sizes can be calculated. (d) The ratios of successive diameters of particles are in geometric progression.

Jan 1, 1947

By K. C. Marsden, B. Pesic

"Interest in the efficient production and recycling of rare earth elements has increased in recent years along with the prices of these elements. The molten LiCl-KCl eutectic is one ionic solvent which can be utilized for these purposes. The LiCl-KCl eutectic has also been selected as the electrolyte for focused research for advanced pyrochemical recycling processes for used nuclear fuel in several nations. Rare earth elements are fission products with notable neutron absorption characteristics, and thorough understanding of the properties and behavior of these elements is critical to their successful partition from the electrochemically-similar actinide elements. The number of research papers investigating individual rare earth elements has greatly expanded in the approximately 35 years since the last review. These research papers are presented in a variety of languages and technical formats, making data difficult to compare, and are sometimes contradictory. A review and summary of diffusion properties of rare earths in LiCl-KCl eutectic was performed, and the data translated to a common format for evaluation. INTRODUCTIONThe rare earth elements have experienced growing importance in recent decades due to their application in high technology, including optical lenses, lasers, high-temperature superconductors, improved alloys, high energy-density batteries, and powerful magnets for compact electronic devices. Their historic production methods and uses are detailed in several texts (Hampel 1971; Bautista &Jackson 1992; Gupta & Krishnamurthy 2005). A s the p rice o f these e lements has r isen in r ecent years, so has interest in their efficient production and possible recycling options. Rare earth oxides are concentrated through hydrometallurgical techniques, but the high thermochemical stability of their oxides precludes production of rare earth metals in aqueous systems. However, the wide electrochemical window and better control of pO2- in fused salt systems allows the production of these reactive metals from their halides or oxides. The high ionic conductivity and diffusivity of the molten ionic electrolyte allow high currents with limited resistive losses (Fray 1980). Electrolytic methods in fused salts are commonly adopted for the production of bulk rare earths in a variety of molten salt systems. Fluorides are sometimes proposed for oxide electrowinning processes due to ability to dissolve the rare earth oxide, reduced hygroscopic behavior, and the wider electrochemical separation between O2 and halide gas evolution (Mohan Das, Damodaran et al. 1988; Gibilaro, Pivato et al. 2011). However, in most electrolytic production processes, such as that for mischmetal, the rare earth oxides are converted to chloride prior to electrolysis in a chloride bath (Gschneidner Jr. & Eyring 1978; Sharma 1987). Of the chlorides, the LiCl-KCl eutectic is one specific medium in which metal production and production-related investigations have been conducted (Gschneidner J r. & Eyring 1978; Driscoll & Fray 1993). L iCl-KCl eutectic has the advantages o f h igh conductivity, but relatively low viscosity and operating temperature. The low operating temperature allows simpler design, with reduced energy consumption, salt volatility and cell corrosion."

Jan 1, 2012

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015