Search Documents

By E. A. G. Colls

PART I.-GASES IN INDUSTRY INTRODUCTION THE part played by gases in industry can be considered from at least four distinct viewpoints, viz: (1) As air to support combustion and life and do various kinds of work (2) As fuel, or as essential to certain chemical processes (3) As sources of danger from explosion or fire ( 4) As hazards to man's health The present paper deals with gases only insofar as they are sources of danger, or are hazards to health. It may be noted, however, that, in point of tonnage, air is one of the most important materials handled in any industrial plant. In the operations of the Consolidated Mining and Smelting Company, for example, 138,000 tons of air are handled daily, the only material exceeding this figure being water. The United States Bureau of Mines has listed no fewer than seventy-four gases and vapours that, under certain conditions, may be considered as ex-plosive or dangerous (poisonous). The commonest and most important of these are as follows : Carbon monoxide Methane Acetylene Hydrogen Oxygen Hydrogen sulphide Benzol vapour Ammonia Petroleum vapour Carbon disulphide Hydrochloric acid gas Cyanogen Carbon oxysulphide Chlorine ` Fluorine (and fluorides) Acetone vapour Acetic acid vapour Water gas Natural gas Gasoline vapour Coal gas Producer gas Ether vapour Nitrogen oxides

Jan 1, 1940

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By P. Langlois, G. Labonté, J. J. Barrett, J. Holmes

"The Voisey’s Bay mill processes a high-grade pentlandite and chalcopyrite ore in a largely pyrrhotite/troilite matrix. From 1994 to 1997, circuit development focused on making a 14% nickel concentrate. When flowsheet development resumed in 2001, the target grade was raised to 20% ni. initially triethylene tetramine and sulfite pyrrhotite depressants were used in a lime circuit, but by recycling process water and the contained thiosalts, the required nickel grade was made without depressants. construction of the mill was fast-tracked, with start-up in september 2005. ramp-up was faster than other recent nickel installations, with tonnage being limited by concentrate dewatering due to higher-thanexpected ore grades.RÉSUMÉ l’usine de traitement de Voisey’s Bay traite un minerai à teneur élevée en pentlandite et chalcopyrite dans une matrice formée surtout de pyrrhotite/troïlite. De 1994 à 1997, le développement du circuit ciblait la production d’un concentré à 14 % de nickel. lorsque le développement du schéma de traitement a été repris en 2001, la teneur cible a été élevée à 20 % de ni. initialement les déprimants triéthylènetétramine et sulfite de la pyrrhotite étaient utilisés dans un circuit à la chaux; cependant, en recyclant l’eau du procédé et les sulfosels qui y sont contenus, la teneur en nickel a été atteinte sans utilisation de déprimants. la construction de l’usine de traitement a été accélérée et elle a démarré en septembre 2005. la mise en opération a été plus rapide que pour d’autres installations récentes de nickel; le tonnage traité étant limité par le séchage du concentré en raison des teneurs de minerai plus élevées que prévu.INTRODUCTIONnickel was discovered on canada’s east coast in the vicinity of Voisey’s Bay, northern labrador, by chislett and Verbiski (Higgins, 2011) while working for Diamond Fields resources in 1993. The ovoid deposit was subsequently delineated in the winter of 1994–1995. By the end of 1995, the ovoid had been well explored, and at that time was thought to have a reserve of at least 30 million tonnes (Mt), with an average grade of 2.83% ni and 2.0% cu (naldrett, singh, Krstic, & li, 2000). Drilling to the east of the ovoid indicated the presence of significant mineralization. in June 1995, inco limited bought a 25% share in the Voisey’s Bay nickel company (VBnc), which was a subsidiary holding company set up by Diamond Fields. inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBnc for 20 years as part of this agreement. in april 1996, inco bought Diamond Fields and acquired the remaining 75% of VBnc shares."

Jan 1, 2017

By Silvana Costa

The quality of life in remote mining communities is a significant factor that impacts the mining industry?s ability to attract and retain high quality workers in remote areas. The rapid growth of mining development, along with the shortage of skills and training globally are reflected in an increasing need to identify the ideal conditions for employee wellbeing and investigate ways to improve quality of life of miners and their families in remote locations.

May 1, 2007

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By D. Yuan, L. Yan, M. J. Collins, P. Kalanchey, I. M. Masters

ABSTRACT Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Because the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The “lime boil” process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95–98%; silver extraction was up to 94%.

Jan 1, 2013

By I. R. Jonasson, R. W. Boyle

"Current interest in the distribution of mercury in the natural environment comes from quite different, though not unrelated, sources. Mercury has long been an important metal in many industries and has, therefore, been much sought after by mining interests. The presence of mercury traces in the various media of the natural environment, namely soil, rock, air, water and vegetation, is exploited by geochemists not only to find mercury and polymetallic ore deposits, but also to find most other types of economic metal mineralization. More recently, however, mercury has caught the attention of health authorities and environmental scientists who are becoming increasingly concerned over the hazards of mercury wastes and the danger these present to the environment and to man. It is now apparent that the trace quantities of mercury, considered so important and helpful to exploration geologists, can be concentrated in the biosphere to such levels as to present considerable problems for ecologists. This article summarizes most of the available data on mercury contents in materials of geological interest and presents average normal values for rocks, ores, minerals, soils, sediments, waters and plants. The geoch.emical cycle for mercury in nature is presented and the mechanisms of mercury migration around the cycle are discussed."

Jan 1, 1972

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By R. Pressacco

"IntroductionAgrium’s history in fertilizer production and marketing goes back to 1931. Today, Agrium Inc. is a world leader in the production, distribution, and marketing of fertilizers and related products to the agricultural industry. Agrium is the largest North American producer of nitrogen fertilizers, a major producer of phosphate and potash fertilizers, and a world leader in fertilizer wholesale distribution and retail marketing. The mine at Kapuskasing is located some 40 km southwest of Kapuskasing, Ontario (Fig. 1). It has been developed to supply high-quality, low-cost phosphate rock to the company’s Redwater, Alberta facility, where it is an ingredient in ammonium phosphate fertilizer production. The Kapuskasing mine is the only phosphate mine in Canada and will rank as one of the highest-grade phosphate mines in the world (Clark and Duncan, 1999). Apatite is the principal ore mineral mined at the Kapuskasing Phosphate Operations.GeologyThe first record of exploration in the area was from a program executed by Continental Copper Mines in 1955 which evaluated the magnetic anomaly located in the Cargill and Cumming townships for its base metal potential. Intermittent exploration of the base metal potential of this magnetic anomaly continued in the following years, until the phosphate potential of the area was first examined in 1974 by International Minerals Corporation which recognized the presence of a layer of apatite sands overlying the carbonatite host rocks.The local geology consists of a core complex of multi-phased carbonatite rocks which are surrounded by a ring of pyroxenite, and have provided a U-Pb age date of 1907 Ma ± 4 (Sage, 1988). These two rock types are in turn situated within quartz diorite gneisses that form a large portion of the Kapuskasing Structural Zone (Fig. 2). The carbonatite host rock is sub-divided into two sub-types: sovite and rauhaugite. The sovite is a medium- to coarse-grained, white, banded rock in which calcite is the dominant carbonate species and it includes accessory minerals such as phlogopite, magnetite, clinohumite, apatite, olivine, pyrrhotite, and amphibole. Apatite can reach 15% abundance in this rock type (Sage, 1988). In sharp contrast to the sovite, the rauhaugite appears as a massive, fine-grained, dense, beige to tan-coloured rock in which dolomite is the dominant carbonate species. Phosphate values can range to 14% P2O5 in the rauhaugite."

Jan 1, 2001

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015

By William E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential.INTRODUCTIONThe purpose of this paper is to describe a cost approach to the valuation of mineral exploration properties and to provide some valuation examples. The particular cost approach described is the Appraised Value Method, which is best applied to mineral properties at the exploration stage.At present there are no comprehensive regulations or guidelines in Canada which specify what approaches and methods to use for the valuation of mineral properties. In this paper, the Appraised Value Method described is one method that the writer considers to be accepted industry practice for mineral properties at the exploration stage.Mineral properties are valued for a number of reasons, including mergers and acquisitions, non arm's length transactions, pricing of initial public offering of stock, support for property agreements, litigation, expropriation, and insurance claims."

Jan 1, 2003

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai.INTRODUCTIONComminution is a very energy intensive process. It consumes approximately 5% of the electricity produced worldwide and more than 50% of the total energy used in mineral processing plants (Pokrajcic, 2010). Among all the comminution stages, ball milling is one of the most energy intensive processes. In ball mills, rotational movement provides the rise of the load and the media that are projected and impact on the mill shell at lower angular displacement, resulting in particle breakage. Ball mills are able to reduce particle size over a relatively wide range of particle sizes. This explains their wide applicability in research laboratories and the mineral processing industry."

Jan 1, 2017

By Oliver Bowles

Cementing materials of mineral origin were well known to the ancients. Ordinary lime and gypsum plasters were the first to be recorded by historians. The next development was the discovery that certain limes would set under water, but the hydraulic property was not definitely attributed to the presence of clay in the limestone until many centuries later. The Romans advanced a step nearer to modern cement in the development of &apos;pozzuolana&apos;, a mixture of volcanic ash or trass with hydrated lime. The silicate of aluminium in the volcanic rock combined readily with the lime, forming a hydraulic mortar or cement which was widely used. Natural Cement In Europe (1) No further progress was made in the art of manufacturing cement for several centuries, during which the Roman Empire declined and passed away, and the Anglo-Saxon race slowly and painfully evolved through the Middle Ages an ever-increasing prestige. An Englishman, John Smeaton, is credited with the honour of the next important development, for he employed a little-known cementing material-natural cement-in constructing the Eddystone lighthouse in 1756. It was called &apos;natural&apos; cement because it was made from a natural rock with no additions of other materials. The process consisted of calcining an argillaceous limestone at a comparatively low temperature and grinding the product to a fine powder. Care was exercised to keep the temperature low, and any material burned to the clinkering point was thrown away, although such material was, as learned at a later time, Portland cement.

Jan 1, 1933

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

By Elmer Palmer

As part of the Goldcorp Inc growth plan Minera Peñasquito SA de CV has developed its polymetallic deposit with a large ?state of the art? concentrator to process lead and zinc ores. The plant consists of two grinding lines including 38ft diameter SAG mills and 24ft diameter ball mills. During mid to late 2009 concentrator commissioning activities commenced. First concentrates were produced in October 2009 and now the plant is meeting its design basis of 65,000 mtpd per line. This paper describes the design and operational experience to date for its grinding circuit design, together with the recently commissioned HPGR crushing circuit.

Jan 1, 2012

By Arthur Barnes, Mika Muinonen, M. J. Lavigne

"The carbothermic reduction of chromite ore to produce high carbon ferrochromium is among the most energy intensive metal extraction processes performed, due not only to the highly endothermic nature of the reduction reactions but also the very high operating temperatures required for the smelting operation to separate the chrome-containing alloy from the discard slag.KWG Resources and XPS have collaborated over the last 3 years in developing a patented (Winter) processing alternative to the traditional smelting operation in which all processing takes place in the solid state at temperatures many hundreds of degrees lower than those required for liquid processing. Amongst the attractions of the process are much lower capital costs, as well as reduced operating costs, particularly of energy.A techno-economic study on the new process identifies a reduction in overall energy consumption of 70% against conventional processing and approximately 40% lower than the current best practice. By utilising more natural gas than coal based energy sources, the KWG process is able to show an overall 50% reduction in greenhouse gas emissions compared with the most energy efficient current practice. The impact of the new process on future processing is therefore regarded as highly significant, with global energy reductions equivalent to the effect of completely eliminating energy demand from a country the size of Italy.The study concluded that the potential for this process to completely revolutionise the global ferrochrome industry should not be underestimated. Its impact reaches far beyond exploitation of a regional natural resource."

Jan 1, 2015

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966