Search Documents

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By A. Brown

The swift decline of coal during the period of unprecedented expansion in the Canadian economy is a phenomenon deserving careful examination, because the underlying forces contributing to this decline may have broader implications in our national economy. At the present level of technology, coal is more difficult to process, transport and utilize than liquid and gaseous fuels. Fundamentally, it is a matter of limitation in technique. Because coal is a vast store-house of energy in Canada, the reduction of these limitations is in the long-term national interest.

Jan 1, 1967

By Janice Zinck

?Past? Images of Mining ?Historic practices have been poor ?Mining still widely perceived as environmental ?spoiler? ?Public only hears the bad news stories. Lessons Learned from the Past ?Sustainability matters ?Recognition of social and environmental responsibilities ?Recognition of importance of public concerns and perceptions ?Community engagement

May 1, 2009

By M. H. Fathi

The aim of this work was to prepare the metallic coatings on 316L stainless steel dental implant and evaluate the corrosion characteristics and thus the biocompatibility of the uncoated and metallic coated dental implants and comparison of the effect of the type of coatings on biocompatibility. Three types of metallic coatings including Tantalum, Niobium, and Titanium coatings were made using physical vapor deposition process on 316L stainless steel dental implant. Structural characterization techniques including; X-ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Analysis were utilized to investigate the microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed in two types of physiological solutions at 37±1 °C in order to determine and compare the corrosion characteristics. All three types of metallic coatings had a positive effect on improvement of the corrosion behavior so that the coatings could increase the corrosion resistance of 316L stainless steel and this trend was independent to the type of physiological environment. Biocompatible metallic coatings could decrease the corrosion current density that is a distinct advantage for prevention of ion release. This can improve the biocompatibility of the implant and, consequently prevention of tissue damages, inflammation and irritation and obtained desirable histopathological response.

Jan 1, 2007

By Edgar A. Manker

"Today's market for columbium has only developed in the last two decades, and in this sense it is ""newer"" than molybdenum, vanadium and most other steel alloying elements. In this short period, it has assumed a very important role in steel alloying and in superalloys. From a few hundred thousand pounds of columbium in 1960, consumption has grown to nearly 30 million pounds per year, with a market value approaching two hundred million dollars.To assess the outlook for columbium, we will first consider the historical development of consumption and supply, particularly noting that all of today's major mines were developed during the last two decades. From current production, we will attempt to reasonably project the future. This future may well include new producers, particularly some producing columbium as a co-product with tantalum.The growth of current applications, and emerging new applications, will be considered with regard to future consumption and in relation to future trends in pricing.IntroductionThe nineteenth century was a busy time for the discovery and naming of new elements. Among those discovered were columbium in 1801 and niobium in 1844. Although it was later shown that columbium and niobium are the same element, the two names are still used today. Niobium has been pronounced the ""official"" name by the International Union of Pure and Applied Chemistry, but columbium is still widely used in commercial practice, and we have chosen to use columbium in this paper."

Jan 1, 1981

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

"Block caving is the preferred underground mining method to profitably extract massive, low-grade orebodies; however, lack of cave access inhibits understanding the rockmass response to mining, which is needed for safer, more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualization (VRSV) is an alternative method for understanding complex cave behaviour, by providing virtual access to the cave. A customized VRSV module was developed at UNSW Australia to investigate rockmass response to undercut developments at a case-study block caving operation. Time/sequence effects are investigated in rockmass response to blasting, which is an important factor in hard-rock mines.RÉSUMÉ La méthode d’extraction souterraine par blocs foudroyés est la méthode préférentielle pour extraire rentablement des gisements massifs à faible teneur. Toutefois, le manque d’accès à la chambre restreint la compréhension de la réponse de la masse rocheuse à l’exploitation, ce qui est nécessaire pour obtenir des opérations plus sécuritaires et plus productives. La combinaison de grands ensembles de données de multiples sources avec la visualisation scientifique par réalité virtuelle (VRSV) constitue un autre moyen de comprendre le comportement complexe de la chambre en fournissant un accès virtuel à la chambre. Un module de VRSV sur mesure a été développé à l’Université de Nouvelles-Galles du Sud (UNSW) en Australie afin d’étudier, dans une étude de cas d’une exploitation par blocs foudroyés, la réponse de la masse rocheuse aux développements de galeries de sous-cavage. Les effets de temps/séquence sont étudiés dans la réponse de la masse rocheuse au sautage, ce qui est un facteur important dans les mines de roches dures."

Jan 1, 2016

By E. Tulcanaza

Mining companies normally establish exploration and research programs originated with actions in embryonic stage. At their early stages of development, these exploration and technological activities are subject to uncertainties that need, first, to be resolved, deciphered or, at least, mitigated for information reporting; and later, for valuation reporting. Under these circumstances, these exploration activities follow a sequence of development phases that range from exploration work to the profile, conceptual, and finally to basic engineering phases and construction. For information reporting, the International Template for Reporting of Exploration Results, Mineral Resources and Mineral Reserves integrates the minimum standards being adopted by the relevant professional bodies in Australia, Canada, South Africa, Chile, USA, UK, Ireland, and other European countries which set up the Committee for Mineral Reserves International Reporting Standards (CRIRSCO, www.crirsco.com). These standards are based on the progressive collection of relevant information to reduce present and future uncertainties over time under a context of transparency, materiality, and technical competence. For valuation reporting several procedures have been disclosed and applied. However, in the last decades financial instruments such as real options, decision analysis, and games theory have developed into a niche of great potential for mine valuation applications. The objective of this paper is to provide a summary of the information reporting standards prepared by the Chilean National Commission for the Qualification of Competent Persons in Mineral Resources and Mineral Reserves and show a procedure and an application of real options to the valuation of the sequential development phases of a mine asset from the exploration stage through up to full development.

Jan 1, 2007

By James J. Holmes

ACCIDENT prevention as we know and understand it today is of comparatively recent origin. As a matter of fact, the Industrial Accident Prevention Association of Ontario, which is the oldest organization of its kind in the Dominion, celebrated its thirtieth anniversary only this year. On the other hand, one could say that the history of accident prevention is almost the history of mankind itself. In a general sense, every forward step that man has made throughout the centuries has been largely due to two things: (1) a desire for increased comfort, and (2) the need for safety; and, always, the need for safety has taken precedence over the desire for comfort. While it is true that hundreds of volumes have been published, dealing with the many aspects of accident prevention work, you cannot go to a library and pick out a book that has all the answers in it. Such a book has never been published-we are still looking for some of the answers. However, a good deal of real progress has been made.

Jan 1, 1945

By C. G. McLachlan

INTRODUCTION The work described in the following paper was under-taken with a view to determining, if possible, the relative importance of some of the phenomena on which flotation seems to depend, in the hope that, if this information could be obtained, it would be of value in dealing with the problem as a whole. At the outset, brief reference will be made to three papers which had a considerable bearing on the course followed in the present investigation. In 1919, Langmuir, in a paper on 'The Mechanism of the Surface Phenomena of Flotation', showed that mono-molecular films of very great stability could be produced on solid surfaces with oleic acid, but that pure paraffin oil, though spreading readily on a dean dry surface, was easily displaced by water.

Jan 1, 1926

By F. E. Lathe

RECENT events have emphasized with renewed force the well known fact that war greatly intensifies the demand for certain metals, particularly for iron, copper, and zinc. Any increase in the use of iron and steel, whether in war or peace, is also accompanied by increased consumption of those metals which find their chief application as ferro-alloys, such as nickel, chromium, manganese, molybdenum, tungsten, and vanadium. Further, since high temperatures are essential for the production of all these metals, activity in the metal industry is inevitably accompanied by an insistent demand for refractories. For example, in North American practice the consumption of magnesitic hearth refractories is frequently expressed in pounds per ton of steel. This quantity (not including straight dolomite) ranges on individual plants from about 7 to 12 pounds. When the industry is operating at approximately full capacity, the ratio of refractory to steel tends to increase, since the tonnage of steel produced is recognized as of paramount importance, and this leads to the harder driving of furnaces and less regard for the effect on refractories. It should also be observed that the cost of refractories per ton of metal produced is always so low, in comparison with other items, that it may even increase while the cost of metal per ton is being reduced through more continuous operation and the use of higher temperatures. As one prominent Canadian copper metallurgist has tersely expressed it, he is "not in business to save refractories but to smelt ore". The effect of war demands and of general industrial activity upon the production of basic and neutral refractories is clearly shown in Figure 1, which gives the value of chrome ore and magnesitic-dolomite produced in Canada during the period 1907 to 1937. Tonnages have not been shown, as these are not available for the full period; such figures as have been published from time to time are not strictly comparable, since both raw rock and finished products have on occasion been included. The preliminary figures for 1938, which are now available, have been prepared by the Dominion Bureau of Statistics on a different basis from those immediately preceding, and have therefore not been shown.

Jan 1, 1940

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By P. D. R. Maltby

This paper describes the background and markets for calcium carbonate and silica sand in Canada, as well as the results of recent test work carried out at the Ontario Research Foundation. Tests on sericite, tremolite, vermiculite, barite and graphite are also mentioned.

Jan 1, 1979

By Blaycock. S. C.

WE should indeed feel proud and satisfied with the accomplishments of our great mining and metallurgical. industries during the past quarter of a century, for they have vastly exceeded those of any previous period of like duration. 1 feel that Canadians, and particularly those in the mining industry, should know more concerning the important role our industry will be called upon to play in the present war. Our Empire metals will be an outstanding factor in this conflict. Every man connected with the industry, from the lowest paid labourer to the highest official, can feel proud that his every effort results in more and more production of those metals which will help to give the Empire supremacy. He can feel assured that, by sticking to his job and by putting his whole heart into his work, he is making a contribution towards winning the terrible struggle in which our Empire and our gallant French allies are engaged. These two great peoples will have ro bear the brunt of the task of ridding the world of the menace of those who would set up force. and might in the place of right and justice in the settlement of international affairs. As the present European crisis developed, it became evident that they, alone, would have to accept the challenge and fight the enemies of Democracy to ensure the survival of the small nations of Europe and, indeed, of the great democratic powers themselves. The acquisitive eye of the German leaders had looked far ahead and they had realized that the eastern European states, already reeming with population, were no solution to Germany's space problem; but they thought that these states could be gobbled up one by one, each in turn strengthening Germany's might until it could successfully challenge France and England. No glimmer of doubt dimmed their vision. The two great democracies once subdued, they could proceed to seize Canada and the United States. This clone, they would have an abundance of room to expand, as well as those resources-grain, timber, cotton, nickel, iron, lead, zinc, copper, gold, silver, sulphur, oil-which German statesmen have always coveted. Von Ribbentrop, von Alvensleben, Bernstorff, and many others have made exhaustive studies of our resources. German rulers had been told that the French would not fight and that the British could not. They knew of the rust on the British war machine. There was no cloud in the sky; their fond dream was at last robe fulfilled.

Jan 1, 1940

By J. N. Brooke

"This paper deals with the training of the mining and mineral engineer and the role that these professional people must play in their company environment, particularly in relation to management.THERE IS SOME CONCERN in the mining industry that the numbers of engineering graduates attracted to it and the academic training that these people have received is inappropriate. Evidence for this is:1. -The meetings and studies initiated by the various mining engineering societies to discuss:(a) attracting students and graduates to the industry; and (b) the appropriateness of the present academic training for the needs of the industry."

Jan 1, 1968

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By J. J. . BRUMMER

Kimber/ires are intrusive rocks whose main constituenr, olivine, has been altered entirely or almosr enrirely ro serpentine. Texture usually is porphyritic, superimposed upon a brecciared one. Diamonds are found only in kimberlites, and are present in economic quantities only in about I% of all kimberlites known. Two glacial drift diamonds, one near Peterborough and one near Timmins, both in Ontario, have been found in Canada and are believed to have been eroded and rransporred from their original source by glaciers. Many more glacial drift diamonds have been found sourh of rhe Great Lakes in the United States, parricularly in Indiana, Illinois and Wisconsin . There are nine known kimberlire occurrences in Canada. Diamonds have been located in rwo of rhem: on lie Bizard near Monrreal and on Somerset Island in the Northwesr Terrirories. The lie Bizard occurrence comprises three kimberlire diarremes; samples of rhe largest one revealed JO riny diamonds totalling 0.0537 carars. The Somerset Island kimberlites are rhe mosr significant yet discovered in Canada. Ar leasr 19 separare kimberlite occurrences are known on rhe island. Testing by Diapros Canada Lim ired, however, revealed only "a few small diamonds". fr is likely rhar, wirh enough time and funds, additional kimberlires, possibly bearing economic quanriries of diamonds, will be found in Canada.

Jan 1, 1984

By Z. D. Hora

The major fluorite producer in British Columbia was the Rock Candy Mine, inactive since 1942. Other deposits of economic interest include the Rexspar deposit, in which fluorite is associated with uranium and rare earth mineralization, and the Eaglet and Liard River occurrences. THE former Rock Candy fluorite mine, located 26 km north of Grand Forks, is the only major past producer of fluorite in British Columbia. The deposit was in production from 1918 to 1929 and again in 1942; total output was about 36,000 tonnes with average grade between 22 and 32 per cent CaF2. The fluorite body occupies a steeply-dipping vein structure, approximately 175 m long and up to 12 m wide, in porphyritic syenite. The chief vein-filling minerals are quartz and fluorite with local small len ses of barite. Fluorite content decreases with depth and the deposit becomes silicified. The Rexspar (or Birch Island) fluorite deposit is located 130 km north of Kamloops. The deposit is complex with rare earth elements and high uranium values, but !1uorite mineralization forms an independent zone adjacent to the uranium orebodies. Fluorite is present as fine-grained impregnations and as breccia cement in strongly schistose or brecciated alkali feld spar porphyry. Reported reserves are 1,088,000 tonnes of 22 per cent CaF2 or 450,000 tonnes of 29 per cent CaF2. 268 Another potential deposit of fluorite is Eaglet, situated on the north side of Quesnel Lake. Fluorite occurs as a stock work with scattered veins and irregular lenses up to 20 centimetres wide and as impregnations in altered Proterozoic Kaza Group feld spathic gneiss over an area of 1,500 metres by 500 metres. To date (1983) approximately $2 million have been spent on the exploration of this property and reserves of 18.8 mimon tonnes grading 11.59 per cent CaF2 have been outlined . A group of significant occurrences is known from north of Liard River Hot Springs Park , where fluorite occurs in small zones up to 17 m thick along the interface between Middle Devonian Dunedin Formation limestone and Middle Devonian to Mississippian Besa River Formation argillite. Fluorite, associated with witherite, barytocalcite and barite, is present as replacement bodies, breccia fillings and minor veins.

Jan 1, 1984

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966