Search Documents

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By A. Mazhary

"Although ore sorting in mining is not a new concept, sensor-based sorting has failed to gain broad acceptance due to perceived challenges with the technology. In order to gain wider applications, this research focuses on treating waste rock and low-grade ore to identify and test appropriate sensors and to evaluate the response. Results showed that amenability of rocks to sensor-based ore sorting is both sensor and ore specific. It was also observed that the efficiency (recovery) of sorting is directly influenced by the degree of heterogeneity of the rocks. The overall outcome showed that with the right sensor, several of the materials tested are amenable to sensor-based ore sorting. Mining companies could benefit from multiple economic and design impacts, such as lower energy cost, lower transportation costs, higher metal recoveries and smaller footprints that lead to more sustainable mining. This paper will focus on the effects of heterogeneity of rocks on sorting potential and efficiency.IntroductionSensor-based ore sorting has been attracting more attention since the pressure for effective resource extraction and management has increased. An urge to make most of the current deposits, and to make the low-grade deposits economic to mine has ushered the technology to find new ways to overcome the new challenges. No matter the terminology used, such as coarse beneificiation, waste rejection, particle or bulk sorting, the purpose of sensor-based ore sorting is to remove low-grade rocks before the comminution circuit, increasing the feed head grade and quality while reducing the energy costs related to comminution.Despite nominal advantages, there have always been some concerns that have impeded the intorduction and acceptance of the technology. One of the most important shortcomings of ore sorting is their capability, or capacity, to keep up with the high-tonnage mining. Some other issues that have been mentioned as drawbacks to sorting include installation cost of such devices, feed preparation for effiecient sorting along with accuracy of sorting and probability of false negatives (Manouchehri, 2003)."

Jan 1, 2015

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By F. Charette

The paper reviews recent investigations of the impact of corrosion on the performance of both plain and coated Swellex rock bolts. It addresses the problems associated with estimating and predicting corrosion rates of friction bolts, and based on field data it suggests an empirical relationship to predict corrosion rates. A review of the necessary qualities for a protective coating leads to recent experience with coated Swellex bolts that suggest that they can contribute to extending the useful life of Swellex bolts in potentially corrosive environments.

May 1, 2004

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

By Maarten van de Vijfeijken, Marco Rufli

"By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The advanced operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore highest availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives (Ravani von Ow and Bomvisinho, 2010; Ravani von Ow and Gerhard, 2010). However this paper will not only show and explain the operational benefit of these functions, but will focus on the experiences gained with this kind of sophisticated ring geared mill drive system. Several measurements of different operating conditions (starting, frozen charge remover, controlled roll back, backlash, etc.) made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. Also the accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.INTRODUCTIONLooking at the demands of grinding mills, we can split them into operational, maintenance and protective demands. For smooth and safe operation, it is important that critical situations are avoided as much as possible. Maintenance functionality must be quick and easy to execute, while protection of the system is important during all operating conditions. ABB has considered all these demands during development of their dedicated mill functions. By adding an additional controller (mill controller), not only a lot of application related functionality and protection is included, but also the interface between the mill drive system and the customer’s distributed control system (DCS) is simplified."

Jan 1, 2011

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By Joe Pease

"The demand for minerals and metals is increasing. Head grades of ore bodies are dropping. Remaining ores are becoming finer grained, more complex, and more logistically challenging. Mineral processing – in particular comminution – already consumes a huge amount of energy. But in 20 years’ time, it will require about six times as much energy as today to meet the world’s mineral demand.Unless we do something different.As minerals professionals, it is our job to find that “something different”. The world is relying on us. Of course, we must look for new breakthrough technologies and techniques. We must find them, and we will find them – most likely in surprising areas.But what if we also already know how to make 30-50% improvements to efficiency? Just by using existing technologies, by applying modern analytical techniques, by custom designing our plants, by applying manufacturing principles, by breaking down our management silos between disciplines.The thing is, industry professionals already know this. Yet – in spite of a lot of intelligent people trying very hard – we just can’t seem to make it happen.This discussion considers why, despite our best efforts, we don’t get the best out of what we already have. Why we are wasting energy and money. Once we understand why, we can set about unlocking that value and improving industry productivity and energy efficiency. We will discuss the role that professionals and volunteer professional organisations like CMP and CEEC can play in catalysing the changes."

Jan 1, 2015

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014