Search Documents

By E. S. Malloch

THE Great War forced the peoples of the world to recognize the importance of the wise development and use of the world's natural resources. Not the least, and perhaps the most, important, is the world's fuel supply- solid, liquid, and gaseous. Without fuel our civilization would be impossible, and mankind would of necessity have to congregate in the torrid zones of the earth's surface for at least six months of every year. Of the three classes of fuels the solid ones are the most plentiful, as well as being the most widely distributed, since few countries are entirely devoid of solid fuels of one kind or another. Until a hundred years ago wood was the fuel most generally used in this country, but since then coal has supplanted wood as a fuel in all its uses, except in the outlying districts and among the farming communities. For many years the supply of coal was thought to be unlimited, but as years went by more thought and study were given to the world's coal resources, until today not only are the limits known, but in one instance at least their depletion is predicted to be almost within the age of living men, unless more provident methods are put into practice for their winning and utilization.

Jan 1, 1928

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By Robert B. Parsons

"Finance Minister Paul Martin's second budget might be good for Canada's mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation's capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin's announcement that rates would not change will be popular."

Jan 1, 1995

By S. Harshaw, C. Doyle, A. E. M. Warner, D. Stremlaw

"In the Utility Nickel furnaces, the hearth and sidewalls are lined with high-Al2O3 bricks. During charging and thermal cycling (more so as the linings on these reverberatory furnaces age), pieces of brick spall or abrade from the refractory and collect on the top of the bath. These pieces are removed using a non-corrosive slag toward the end of the heat when the bath temperature is ~1600°C.This benign liquid can be generated by two methods. First and most obvious, suitable ingredients can be pre-mixed so that the flux (flux A) is isochemical with the non-corrosive slag. All that is needed to produce this targetted slag is heat. Second, in other proportions (flux B), the pre-mixed ingredients generate a corrosive slag that melts completely at -1200 °C and corrodes some but not all of the brick particles on the bath surface. As the reaction progresses, the slag changes composition eventually attaining the targetted benign composition. Using this option, additions are monitored to avoid overfluxing. In both cases, the generated slag/brick mixture can then be rabbled from the furnace. This practice has been successfully used for over two years and has been a factor in extending Utility Nickel furnace life to its current levels (about25% increase)."

Jan 1, 1993

By H. C. L. Reemeyer

"The mining industry faces increasing economic, environmental and social challenges, as easier deposits deplete and ores become more difficult to mine and process; head grades decline; projects migrate to increasingly remote and difficult geographies; and the industry faces more stringent environmental and social standards. While these factors increase costs and risks, they also present opportunities for a more integrated approach to mining, processing, materials handling and waste management. Two key areas of risk are in tailings and water management. As mining and processing tonnage rates continue to increase, the disturbance footprints, water and energy consumption and scale of tailings storage facilities also rise. These factors can be mitigated by more selective mining, ore sorting and pre-concentration, and more intensive tailings dewatering. Such alternatives must be considered in conjunction with the selection of mining method, metallurgical flowsheets, major equipment selection, and key process design criteria. For example, increasing the grind size of a concentrator reduces energy consumption and eases tailings dewatering, but may cause challenges with metal recovery. Emerging technologies will be reviewed, and economic and environmental trade-offs for eco-efficient alternatives will be presented for metal sulfide mines.INTRODUCTION The metals mining industry faces significant challenges that can affect its financial viability and social license to operate. There has been a consistent decline in ore grades and a relentless push towards larger operations to capture perceived economies of scale. With these larger operations, the environmental footprint of mines has increased. Water and energy consumption, and resulting GHG emissions have also risen. In recent years, two issues have raised special concerns for stakeholders and companies: • Water scarcity, particularly in drier regions of the world such as Northern Chile, SW USA, Southern Africa and Australia • Tailings risks, following the high-profile failures of the Fundao tailings dam in Minas Gerais, Brazil in 2015 and the Mount Polley tailings dam in BC, Canada in 2014"

Jan 1, 2017

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By F. D. Ball, D. E. Gemmell

"Coal mining in New Brunswick dates from the year 1639, when, as today, coal was produced from the area surrounding Grand Lake near the geographic centre of the province. Current production by N.B. Coal Ltd. is approximately 453,000 tonnes per year and comes from a single, thin Pennsylvanian age seam. The history of development and understanding of the geological setting of New Brunswick coals is discussed, beginning with the work of A. Gesner in 1839. The lithostratigraphic sub-divisions of the Pennsylvanian strata proposed by various workers are summarized and the present hypothesis that only biostratigraphic subdivision is possible is detailed. The Pictou Group, which includes the New Brunswick coals, consists of repetitive sequences of sediments consistent with flu vial and upper delta plain sedimentation. The development of coal mining in the province has progressed from horse-powered stream-bank stripping operations prior to the late 1800s through to the present use of open stripmining techniques utilizing eight walking draglines of various sizes. During the intervening years the introduction and eventual phasing out of underground mining occurred with the near termination of the coal mining industry in the province prior to 1973. The coal seam worked by N.B. Coal Ltd. averages 46 cm in thickness, has never been found to be more than 76 cm thick and has both high ash (12.4 -31.1%) and sulphur (4.9-7.8%) content. The wide variety of coal beneficiation studies and tests completed on New Brunswick coals have lead to the conclusion that a washed New Brunswick coal product could be expected with 10 to 12% ash, 5 to 6% sulphur, and 30,225 to 31,388 1/gm. Recoverable coal reserves, including those in the area licenced to N.B. Coal Ltd. and those licenced, although not yet in production, to both the St. Lawrence Cement Co. Ltd. and Provincial Holdings Ltd. at Lake Stream and Beersvil/e, total 60 million tonnes. At present, coal in New Brunswick is removed from prospecting and staking and all existing and future coal exploration and development will be administered by agreement under the Mining Act. Based on the results of a recently completed drilling project undertaken by the Department of Natural Resources, seventeen coal exploration blocks which carry minimum work commitments will be offered to the New Brunswick Electric Power Commission on a sixty-day first right ofrefusal basis. Those blocks not taken up by the Power Commission will be offered under the same commitments to the private sector."

Jan 1, 1985

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By C. A. Pickles, D. K. Xia

"In the last few decades, microwave energy has been widely employed in food processing, rubber and plastics curing, and in ceramic sintering. Recently, the application of micro waves as an energy source in extractive metallurgy has received considerable attention from a number of researchers. During the period from the mid-1960s to about 1988, the majority of the research was focussed on the behaviour of materials in microwave radiation. These research activities will continue to be important, since fundamental data on the interaction of microwaves with materials are vital for the successful application of the technology. Since1990, a number of potential applications of microwave processing have been investigated.These include: pretreatment of ores and concentrates, leaching, reduction, preheating of refractories, heating of slags and waste treatment. In this paper, the interaction of micro -waves with materials of interest in extractive metallurgy are reviewed and potential applications are discussed.IntroductionMicrowaves were first used in 1946 for the heating of materials, shortly after radar equipment was invented during the second world war. It was evident that microwaves were very effective for heating water and the technology was quickly adopted for drying and cooking. Since the introduction of the first microwave oven by Raytheon in 1952, many millions of domestic microwave ovens have been sold annually (National Research Council,1994; Atomic Energy of Canada and Voss Associates Engineering, 1990).In extractive metallurgy, microwaves are in the early stages of development (National Research Council, 1994; Atomic Energy of Canada and Voss Associates, 1990; McGill and Walkiewicz, 1987; Bradhurst and Worner, 1990;Peng et al., 1993). However, there are several reasons for the growing interest in the use of this technology in the field of metals extraction. These include the following potential advantages of microwaves: (1) rapid and selective heating of materials; (2) reactions can be catalyzed because the heating occurs on a molecular or atomic level; (3) clean and controllable energy source; (4) the gas volume is reduced and the atmosphere can be controlled as there are no gaseous combustion products; (5) the material is heated internally in comparison to external heating with conventional methods; (6)the temperature of the refractory can be minimized; and (7) the working environment is improved."

Jan 1, 1997

By P. Hajiani

"It has been shown that the economics of the hydrometallurgy of a rare earth process depend upon the amount of acid needed to extract the metal per unit mass of the ore. In this paper, we show how to save a significant amount of acid treating a low grade ferrocarbonatite and extracting +99% constituent REEs. In order to save the acid, the alkali earth metals, originated from gangue minerals were removed prior to REE leaching. Moreover, the operating conditions of leaching reactor are optimized to leave iron behind and to leach REE selectively and effectively. Consequently, the hydrochloric acid consumption per ton of ore drops significantly compared to other processes.INTRODUCTIONThe viability of an extractive metallurgy process of rare earth elements (REEs) to produce an intermediate mixed concentrate depends upon a low-cost simple flowsheet (Bogner, 2014). It has been known that regardless of the mineral, the acid consumption is intimately associated with the operational cost (OPEX) of any REE project, particularly when the initial REE grade is low. Besides acid, the other reagents consumed in the process impact the OPEX. This makes minimizing acid consumption in an REE method a critical priority. The acid consumption in different projects has been reported to be equivalent of 100 kg to 1000 kg HCl (100%) per tonne of ore (Average: 500 kg/t HCl 100%) (Bogner, 2014). This value is strongly correlated with the grade of REE in the ore and therefore in the pre-concentrate.Previously, it has been stated that the Montviel flotation concentrate requires about 300 kg HCl (100%)/t ore to attain +99% REE recoveries using direct leaching (Yu, Verbaan, Pearse and Britt 2013). Hence, for an ore feed rate of 2500 t/d ROM, a large acid production plant (744 t/d HCl 100%) would be required for acid leaching of such concentrate. The equivalent Chlor-alkali plant is estimated to cost M$ 150 (CAPEX) and may require 100 MW power. Therefore, there is a necessity to improve the extractive hydrometallurgy and to reduce the acid consumption significantly."

Jan 1, 2016

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

By B. Crane, S. Schwartz

"IntroductionThe Cape Breton Development Corporation (CBDC) located in Cape Breton, Nova Scotia, in eastern Canada, was established in 1967. Its mandate at that time was to facilitate a phased downsizing of the coal industry and developing viable replacement industries. The oil crisis in the early 1970s changed CBDC’s mandate and focus was modified to increase coal production to support Nova Scotia Power Commission’s “off oil” policy for their power generators. In the late 1980s the mandate to develop viable replacement industries was eliminated and CBDC became primarily a coal mining company. CBDC presently operates two underground coal mines, Phalen Colliery and Prince Colliery, using a retreat longwall method of mining. Both mines operate beneath the Atlantic Ocean. CBDC also operates associated infrastructure — central workshops, a railroad, coal preparation plant, and international pier. The Need For Substantial ChangeOver the last few years, CBDC has been facing some challenging issues, including improving labour management relations and achieving financial self-sufficiency and profitability. Recent achievements with regard to human resource issues, especially in the areas of collective bargaining, absenteeism, and attendance, show noticeable improvements. All participants should be commended for successfully concluding the collective bargaining process with all four CBDC unions, CUPE; CAW; IAM&AW; and UMWA. However, although these changes are encouraging, even critical in the short term, they are not sufficient to ensure the long-term viability of the company. Market ForcesShort- and long-term financial realities are drawing the need for further substantive changes. The corporation has a mandate to achieve financial self-sufficiency by the year 1999. This goal can only be achieved through a combination of cost reductions and productivity gains, specifically, a reduction in the workforce of 658 and an increase in production of 800 000 tonnes annually. This increase in productivity requires CBDC to re-think the way it does things.In the longer term, CBDC faces even greater challenges. The energy market is becoming more competitive. The electrical utilities across Canada are anticipating deregulation and are positioning themselves for the resultant competition. As primary fuel supplier to Nova Scotia Power Inc. (NSPI), the corporation will have to become ever more competitive to stay in business."

Jan 1, 1997

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978