Search Documents

By Cedric E. Gregory

"A study of model rectangular mine shafts has been made in the wind tunnel, with the aim of reducing air-flow resistance elements to a practicable minimum. An analysis of Table 7 shows an indicated average decrease in resistance of 28 per cent by adopting the over-all modifications involved in the configurations actually tested. Much greater reductions (up to 68 per cent) are indicated by extrapolating beyond the test results directly achieved. Intermediate partial reductions in aerodynamic resistance are shown for individual modifications, such as: (1) about 3 per cent for locating the lagging in the No. 4 (inside flush) position as against the No. 1 position - 8 per cent as against the No. 2 position - and 23 per cent as compared with position No. 3; (2) about 12 per cent for using lagging instead of steel meshwork along the divider separating the skipway from the service compartment; (3) about 14 per cent for using steel gridwork ladder stagings at 3-set intervals instead of similarly spaced wooden stagings; (4) about 12 per cent for using steel gridwork ladder stagings at 3-set instead of at 1-set intervals; (5) about 13 per cent for fitting a streamlined fairing (see Fig. 5) to the upstream face of the skipway divider. Contrary to expectations, an advantage of only 3 per cent is indicated for lagging in the inside flush (No. 4) position over the outside position (No. 1). This slight gain does not appear to warrant the cost of moving the lagging. However, if the lagging is already in the No. 2 or No. 3 position, there is an 8 and 23 per cent advantage respectively."

Jan 1, 1973

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By J. P. Cooney

Placer Dome is learning from experience in Latin America, Asia and Africa, as well as in North America, that contributing effectively to sustainable human progress in the areas of its operations presents unending challenges to think creatively, communicate effectively and remain culturally sensitive. People must be better off in terms of their economic circumstances, their social conditions and the quality of their natural environment not only during the life of the mines, but after mines close. Stakeholders, all those who are directly or indirectly affected by a mining project, should be able to participate in decisions which affect them. The development of sustainability strategies, the monitoring of sustainability performance and the implementation of sustainability programs are best done in partnerships with governments, communities, nongovernmental organizations and multilateral development institutions. Ultimately, the success, if not the survival of mining, will depend on our ability to get the sustainability equation correct.

Jan 1, 2000

By E. Laatio, W. McKay

"History of Tara Mines Ltd.Tara Exploration and Development Company Ltd. was formed in Canada by Irishmen in 1953. The discovery of an orebody approximately six miles from the historically famous Hill of Tara in County Meath was a wild dream . Nevertheless this dream became a reality. Tara Mines Ltd. was formed, and the mine developed some 35 miles northwest of the City of Dublin in the Irish Republic.Tara's original drilling program indicated a zinc-lead orebody of approximately 60 million tonnes grading at 10.1% Zn and 2.6% Pb. The terms of the mining lease stipulated that the Irish government would acquire 25% equity interest in the operation. The mine was thus owned 75% by Tara Exploration and Development Company Ltd. of which the principal shareholders were Noranda and Northgate, together with 25% being held by the Irish government. The mine was purchased in March 1986 by Outokumpu Oy, a Finnish mining and metallurgical company, and together with the 25% government stake are the current owners. Outokumpu Analysis on Tara Mines Ltd.Upon ownership Outokumpu carried out a comprehensive analysis on the operation and came to the following conclusions :1. Tara had a good orebody;2. Tara had a skilled, capable, stable workforce;3. Tara's concentrator and processing equipment was adequate to meet requirements;4. Tara's mobile equipment fleet was too old and too numerousin numbers; and5. Tara had too many employees, both staff and hourly paid .With ore reserves of approximately 50 million tonnes and at a planned extraction rate of 2.6 million tonnes it meant that the mine had a lifespan of approximately 20 years. To be a viable operation into the future, the mine had to become more efficient. Operating costs and manpower levels had to be dramatically reduced."

Jan 1, 1989

By Derek V. Ellis

Coastal and marine mines affect the seabed?s biological resources, eg fisheries, when large volume wastes such as tailings are placed on the seabed, and by the extraction processes from marine mining. Worldwide monitoring of such effects for the past 30+ years now provides information to describe Best Practice design, construction and monitoring procedures. The critical environmental factors for submarine tailings placement (STP) are the selection of an appropriate deposition site and discharge depth, the deposition rate of the tailings, and the speed of biodiversity recovery to a sustainable ecological succession. These should be predictable at new sites using current modeling and experimental procedures. Prediction procedures are still needed to minimize potential destabilization of deposited tailings, and consequent biodiversity recovery setbacks. Comparable environmental information is needed from marine mining sites.

May 1, 2002

By W. E. Uren

The Dominion Coal Board was created by Statute passed on July 17th, 1947, and was brought into effect by proclamation on October 21st, 1947. It is, consequently, a comparatively young body, having been in existence for only eighteen months. Before dealing with the constitution and duties of the Board, it may be well to answer the unspoken question of why it has been considered necessary to single out coal as one specific mineral requiring the continuous attention of a specially created permanent Board. In Canada, coal has been the neglected sister of the more spectacular minerals and it comes as a surprise co many to note that in 1948 the value of the coal produced in Canada was higher than that of any other mineral with the one exception of gold. Coal touches upon our daily lives in many different places of which the public are not generally conscious. As household fuel, it is a necessity of life in this northern climate; as a source of steam, it provides the heat for most of our industries; it is the food of the 'iron horse' chat shuttles our persons and our goods across the land; it is the source of power in many parts of the country; it is the chemical reducing agent chat, in our furnaces, transmutes the metallic oxides to the virgin metal. Coal is, in fact, the indispensable mineral chat forms the corner-stone of our present structure of industrial civilization. Is it, then, such an odd thing that the provision of an adequate supply of coal should be a matter of national interest or that measures should have been taken by government co provide for a constant watch, by a permanent Board, on the supply of co al? ? The Board is the result of the recommendations of the Royal Commission on coal which made a long and detailed study of the Canadian coal problem. It is composed of a permanent Chairman and six part-time members, most of whom have had intimate contact with various phases of the industry.

Jan 1, 1949

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By A. E. M. Warner, A. Vahed, P. J. Mackey

"Since early 2015, the price of nickel has dropped from the region of US$6/pound to current levels of around US$4.60/pound (March 2017), reflecting several market factors, but principally due to lower demand from China. Under such conditions, nickel companies have been under pressure to contain operating costs. In addition, labor and energy costs will continue to rise, while nickel ore grades will likely continue to drop. All major companies now accept the need for climate change action and consequently efforts are being made towards lowering carbon-based emissions. Nevertheless, meeting these challenges can also contribute to higher operating costs without parallel innovative developments - which at the same time, under current conditions, major companies are tending to curtail. In this paper, several productivity improvement opportunities to reduce unit operating costs at nickel sulphide and nickel laterite plants are reviewed. Opportunities include: (a) process technology and energy-type selection, production capability, optimization of process intensity and implementation of newer technologies; (b) improved productivity, equipment availability including maintenance best practice; (c) energy savings and recovery opportunities and use of energy surveys and, (d) process modeling and improved scheduling. Such improvements along with an uptick seen in nickel demand going forward should better position the world nickel industry.INTRODUCTION Nickel is an essential metal to modern society, primarily through its use as an important ingredient in stainless steel. Thus, stainless steel finds vital applications in food preparation facilities, as well as important uses in transportation and industrial applications. Canada has always played an important role in nickel production and nickel metallurgy. In the 1940s and 1950s, Canada supplied over 90% of the world’s nickel. However, this proportion has declined considerably to around 10% of the world nickel supply today. Still, Canada remains an important nickel supplier and contributor to nickel extractive technology. Due to the importance of nickel to society, nickel demand is expected to continually rise. On the other hand, nickel companies have been under pressure to contain production costs amid languishing nickel prices. While demand projections show nickel growth, there are uncertainties in actual levels of future market growth. Ore grades are dropping, while labour and energy costs, which are key cost contributors are rising, hence efforts to lower production costs will generally require innovative approaches."

Jan 1, 2017

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By F. J. Alcock

IN the summer of 1934, gold was discovered on Lodge bay, on the north shore of lake Athabaska in northern Saskatchewan, about fifty miles east of the Alberta boundary line. The first claims were taken up by the Consolidated Mining and Smelting Company of Canada, Limited, and there was a 'rush' to locate similar showings. Staking continued through the summer and succeeding winter, and in the spring of 1935 the provincial government established a recording office at a convenient point which is central to the more important holdings and where 'planes can land in any weather. During the past summer, the name of this townsite was changed from Beaverlodge to Goldfields, and a post office was established here. The season was one of great activity; a great deal of assessment and development work was carried out and a large amount of further prospecting done. In addition to the work by private companies, geological investigation was carried out in the region by a Federal Geological Survey party under the charge of the writer and a reconnaissance examination was made of an area of some 7,000 square miles surrounding the region of particular interest. Though this was the first discovery of gold in the region it was not the first occasion that prospecting had been carried out along the north side of lake Athabaska. Over twenty years ago, a number of prospectors were at work in the area and a large number of claims were staked, many of which were never recorded. One man by the name of Piché, in the years 1910, 1912, and 1913, took up a considerable number of claims north of Pine Channel narrows, east of Fond du Lac. His discoveries, which consisted of small showings of sulphides in sedimentary gneiss, proved to be of no economic importance. In 1915, a sudden widespread interest was aroused by the report that a sample of ore collected near Fond du Lac had yielded a very high assay in silver. In March and April of that year, prospectors began to rush into the field by dog teams to take up claims, and, as soon as the Athabaska river was free of ice, others started by boat from Athabaska Landing. Some hundreds of claims were staked and recorded in the Dominion Land Office at Edmonton or at Fort Smith. By July, most of the prospectors had? left the region, having failed to find any silver ore. In 1921, considerable prominence was given to the area a few miles east of Goldfields by reports that very large masses of iron ore were available there. Claims were taken up, but the material is much too low grade to be considered commercial ore.

Jan 1, 1936

By Robert B. Parsons

"Investors in flow-through shares are going to need an expanded road map to find their way through a growing maze of tax rules affecting such shares. At the end of 1985, no fewer than three new sets of important tax amendments were tabled which could have a significant effect on flow-through share issues. This proposed legislation is discussed this month in Tax Notes.IntroductionIn a flurry of legislative activity at the end of 1985, the federal government tabled legislation which includes the introduction of new rules which will have a notable effect on investors in flow-through shares and on companies that issue such shares.First, on November 26, 1985, Bill C-84, the legislation to implement most of the changes announced in the May budget, was introduced in Parliament. This legislation includes the rules for the $500,000 capital gains exemption, a matter of considerable interest to flow through share investors.Next, on December 2, 1985, the government tabled a Notice of Ways and Means Motion which would extend the time horizon for spending flow-through share funds to include the 60-day period following the calendar year. But all news was not good news. On December 4 the government released its proposals for a minimum personal income tax, which would include rules that would catch an investor's CEE expenses and capital gains."

Jan 1, 1986

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By Michel Dostie

Un séchoir à vis chauffé par induction électromagnétique a été développé et implanté chez Mines Niobec pour le séchage d?un concentré de niobium. Ce séchoir a permis une réduction des émissions de poussières et des gaz à effet de serre de l?usine. Il offre une grande souplesse de contrôle, une meilleure efficacité énergétique et peut être utilisé pour le séchage de granulats, de poudres ou autres substances habituellement traitées dans un four rotatif ou à l?aide de vis chauffées par un caloporteur. Le principe de fonctionnement du séchoir est simple. Trois inducteurs opérant à la fréquence du réseau électrique assurent le chauffage des parties métalliques du séchoir, dont des vis qui servent à convoyer le matériel. Le contact du matériel avec les parties métalliques chaudes permet le transfert de l?énergie requise pour le séchage. La conception de ce type de séchoir requiert un équilibre adéquat entre les besoins associés au chauffage par induction et ceux liés au transfert de chaleur par contact et au transport du matériel dans le séchoir. Cette première implantation industrielle a nécessité des efforts de développements importants et une collaboration des différents intervenants. Une revue des principes de conception, des difficultés rencontrées et des performances obtenues sera présentée.

May 1, 2007

By A. Trusiak

"Increasing energy costs in mineral processing is making it necessary for tighter controls over various parts of the concentrating process. Continuous monitoring and control of critical process streams can be easily performed by today's many computer systems. Indeed, the list of successful applications of computers to grinding and flotation control continues to grow. The day is rapidly approaching when the use of computers within concentrators for either process control or simply metallurgical accounting will no longer be a luxury, but a necessity. The benefits from such applications far out weight the initial investment.This paper describes the current application of a process control system at Brunswick Mining in north-eastern New Brunswick. Emphasis is placed on the control of a CuPb flotation circuit, and the benefits derived-from this control.No. 12 Cu-Pb Flotation: The complex nature of the Brunswick flotation process has been described else-where. 1,2,3 Four final concentrates are eventually produced, these being a Zn concentrate assaying 53% Zn, a 30% Pb concentrate, a 20% Cu concentrate, and a bulk Pb Zn concentrate assaying 35% Zn and 17% Pb. The Cu concentate, Pb concentrate, and bulk Pb Zn concentrate are all derived from a primary CuPb concentrate assaying 26% Pb, 11% Zn and 1.8% Cu.The No. 12 CuPb circuit produces approximately two thirds of the total primary CuPb concentrate. No. 12 ore, assaying 3.5% Pb, 9% Zn, 0.25% Cu and 100 g/tne silver, is ground in two parallel grinding circuits. Each line uses a 3.2 x 4.2 meter rod mill in closed circuit with two parallel 3.2 x 3.9 meter ball mills. Ball mill and rod mill discharges are classified in two stages of cycloning. The secondary cyclone overflow, or flotation feed, is controlled at 65% passing 37 microns."

Jan 1, 1981