Search Documents

By Moelle KHR

The successful operation of a longwall face depends significantly on the efficient actions by support systems and on the ability to form a supported beam for a limited time span.The mechanical action of the supports can set up complex stresses in the immediate roofstrata.The cyclic application of supporting loads to the immediate roofstrata of a longwall face creates a special type of fabric disintegration in the rocks -affected. The mode of application and the distribution of the supporting forces is thus severely modified in a number of cases.The occurrence of true fatigue damage in brittle sandstones has been identified by studying the subcritical crack growth and microcrack development in the fracture-tip region. Several mechanical effects peculiar to the cyclic fatigue process have been identified. These effects had not previously been widely recognized. Damage in brittle rocks subjected to cyclic loads is shown to be distinctly different from any other damage processes under either monotonic or sustained (creep) loading conditions. The face support systems will frequently support rockmasses with mechanical properties not identified in conventional monotonic or sustained load tests.

Jan 1, 1991

The major heavy industrial consumers of limestone are the cement, lime'and steel ind- ustries. Each of these requires large quantities of cheap raw material. Other ind- ustries such as glass and chemical manufactur- ing are significant consumers and agricultur- al and constructional activities provide additional demand which is usually more local in its occurrence. Limestone is widely dis- tributed throughout Australia but location in relation to major markets, and transport con- siderations render most deposits of no economic value. Among deposits which are sufficiently close to the major metropolitan markets many must be rejected as being unsuitable on grounds of quality, inadequate size for major.develop- ment, or other reasons such as environmental considerations. The major producing locations are sit- uated in a variety of geological environments. Most have limited reserves and require partic- ular attention to quality control. Planned extraction programmes based on detailed geo- logical investigations enable not only satis- factory grade control but also permit, by the adoption of appropriate quarry procedures, the use of sub-grade material, thus optimis- ing utilisation of the available reserves.

Jan 1, 1976

By Jimbo I, Ogawa O

A series of experiments was carried out to investigate the solubilities of copper, arsenic, antimony and bismuth in silica-saturated iron silicate slags under controlled oxygen partial pressures at 1200 and 1250¦C. Molten copper containing each of the above elements was kept in contact with a slag in a silica crucible for 24 or 48 hours to attain equilibrium. No me- chanical entrapment of metal into the slag was observed. The appearance of the magnetite phase in the slag was avoided by holding oxygen potentials at substantially lower values than that evaluated from available data on iron silicate slags. Solubilities of copper, arsenic, antimony and bismuth in slags were plotted against oxy- gen potentials and both oxidic and atomic types of dissolution were found, except in the case of arsenic, from the dependencies of the solubili- ties on the oxygen potential and from positive intercepts of regression lines when extra- polated to zero oxygen potential. The dissolu- tion of arsenic seemed mostly oxidic. Distri- bution coefficients of arseò,ic, antimony and bismuth between copper and slag are also Discussed.

Jan 1, 1980

By Veal FL

Technological changes in Portland cement manufacturing during past years have reflected changes in the economics and availability of various types of fuel such as coal, fuel oil and natural gas. The industry consumes a sig- nificant quantity of both thermal and electric- al energy. The nature of the process and its chemical constraints does however permit the use of comparatively low grade fuels such as high ash coal and high sulphur oil. In striving for increased daily kiln outputs and conservation of energy, there is a worldwide trend towards the use of dry process plants. Wet process kilns of about 2 500 tonnes per day assume massive component sizes which present difficulties in manufacture, and transport to plant sites. Large capacity dry process units in excess of 8 000 tonnes per day are now in operation using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. This technique has virtually doubled the potential output of any given single kiln.

Jan 1, 1976

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

By D Millette, F Gay

Surface tailings are finely ground waste materials produced in all mines after the mineral or metal has been removed from the metallurgical process. Current methods for disposal of tailings involve constructing dams, dumping into existing waterways, and depositing as backfill underground. Each method has its drawbacks in terms of cost, level of complexity, safety and environmental concerns. Backfilling is the process whereby waste material (generally metallurgical tailings, prepared aggregates or a combination) is placed from the surface back underground into open mine workings via conveyor belts, hydraulic or pneumatic pipes or gravity. In the backfill process common difficulties are expensive placement costs, equipment wear and the ability to meet early and long-term strength requirements. Traditional tailings transportation in pipes involves the use of water as the transport medium. Foam technology involves the introduction of micro-air bubbles that replace the water as the main transport medium. This air can be removed after placement if necessary, by the addition of a defoaming agent. This could produce an under-saturated stable cake. Foam technology has the potential to revolutionise surface tailings disposal and backfilling by providing a less expensive and environmentally safe alternative to those just described.

Jan 1, 2000

Due to collapsing copper prices during 1974/75, a rapid changeover was made at the C.S.A. mine from mechanised cut and fill stoping with incline access to the more economic long hole open stoping method. In 1974/75, 20 per cent of total production came from open stopes. For the 1976/77 year-to- date, more than 80 per cent of total production has been won from open stopes. As a result, mining performance has improved considerably. Stops, drilling performance has increased by more than 50 per cent since the changeover from extension rod, 50 mm diameter cut and fill uphole drilling to 115 mm diameter in-the-hole hammer drilling of holes up to 65 m long. Stops blasting performance has improved from 750 tonnes to 950 tonnes blasted per manshift. Open stope primary blasting per- formance is much higher, but reduces to 950 tonnes per manshift when secondary blasting and firing of hung drawpoints are taken into consideration. Ground control, the most expensive and least productive aspect of cut and fill mining, is almost entirely eliminated in long hole open stoping.

Jan 1, 1977

In simple terms, heap leaching means the removal in solution of valuable elements from a heap of material, and their recovery from that solution. The heap of material can consist of essentially unprocessed ore, sub-ore, low grade gangue and country rock, tailings from other upgrading processes, or artificial materials such as slags or furnace and flue products. The solvents can be solutions of acids (commonly sulphuric acid because of cost) or of other chemicals such as cyanides. Because of cost factors the solutions are aqueous; because of this, leaching operations may be curtailed in cold-climate areas. The guiding principle must surely be `large volume / low cost'. Since solutions are generally easier to manage than gases, there is a strong incentive for replacing roasting of materials by leaching, eg arsenical gold ores. Where sulphides are present in the material to be leached, these may provide the necessary acid, with or without the aid of bacteria, to dissolve and extract the recoverable metals. The mineralogical aspects of the operation relate to the nature of the `ore' and gangue minerals present in the heap, their textural relationships, and their effect on the process itself.

Jan 1, 1994

The paper sets out the context for water and the challenges that have to be faced in the battle to alleviate global poverty. It acknowledges that the world has been blessed with abundant water but because of population and development pressures, and the projected changes in climate, avoiding serious water shortages in some places will be difficult. MiningÆs use of water is placed in context and the paper then considers the specific threats to the industry in terms of availability and price and the need to find mechanisms to deal with the issue of resource degradation caused by abandoned mines. Rio TintoÆs use of water is then set out and three examples are given of how different water challenges have been addressed. The paper goes on to consider each element of a water strategy designed to move Rio TintoÆs performance towards excellence. This strategy incorporates improved management procedures (policy, principles, standards and targets), performance enhancement (through use of the Rio Tinto Water diagnostic and technology changes) and working with others in the academic and NGO community who seek to address the same global issue.

Jan 1, 2003

By J Kinal

Plant trials are at the best of times difficult to perform; given variations in the ore, operating practice and economic constraints placed on a plant. Testing grinding media at industrial scale adds a further level of complexity that needs to be accounted for.Laboratory test programs consistently demonstrate that altering the grinding chemistry through the application of inert grinding media has the potential to provide significant metallurgical benefit. However, prog- ressing from laboratory testing to industrial trial is often an agonisingly slow process that can lead to inconclusive results which raise more questions than give answers. There are many factors that need to be considered when conducting plant trials aimed at demonstrating the impact of inert grinding media on metallurgical performance. The decisions (or lack thereof) made during the planning stage can heavily impact on whether a statistically meaningful result is achieved. Various factors such as how the trial is conducted (dumping or purging the charge); the circuit configuration; collection of the right data; and even the human factor will affect the outcome. The authors will use examples to demonstrate the importance of proper planning and controlled operation on grinding media plant trials.

Jan 1, 2009

By Johnson G. D

Confidence in Yakabindie becoming a truly cost competitive nickel project has risen recently because of: ò the emergence of an economically effective contract mining climate; ò the delivery of cheaper energy via the Goldfields Gas Pipeline; and ò the development of the Yakabindie Process for production of nickel cathode and cobalt by-product directly from sulphide concentrates at site, dramatically cutting capital and operating costs compared to the conventional route. Development of the Yakabindie Process was a result of 'necessity being the mother of invention'. Yakabindie can now break out of the trap of relying on existing downstream processors to treat an intermediate, and instead the project can gain direct market access. The very attractive cost advantages demonstrate that hydrometallurgical processing of sulphide concentrates is a worthy prize. Improved cobalt recoveries, and tolerance of higher levels of magnesium and arsenic than allowable by smelters, are further advantages of this approach. Leach residues are combined with much larger quantities of naturally alkaline flotation tailings and remain at site. As a result the process is more environmentally sensitive than the conventional smelt/refine route, with no sulphur dioxide gas emissions and 'metal only out the gate'.

Jan 1, 1996

Most internationally traded iron ore resources are derived from multiple mine sites, transported to a port facility where they are blended and possibly further processed prior to shipping. Provided the proportion of contributions varies over a number of shipments an estimate can be made of the bias introduced by mine site sampling, analysis and materials handling systems, using zero-intercept multiple linear regression. Further regression applied to the residuals allows the error variances for the source mines to be estimated. Various sampling strategies are used by the industry. All have shipment-loading sampling on which payment or at least provisional payment is based. In most cases sampling prestockpile is used at mine sites to verify estimated production grades. Train grades are estimated from mine stockpile grades and in some cases train grades are verified by port input sampling. The methodology used is presented in this paper. Simulated data have been used and do not reflect the actual performance of any operator. The merits of the various systems and the implementation and potential limitations of our method are discussed more fully in a companion paper (Ziegelaar and Everett, 2010).

Mar 1, 2010

By Gutsche O, Kapur PC

Experimental data on the production of fines as a function of specific grinding energy consumption show that in general the energy utilisation in a choke fed high-pressure roll mill is higher than in a ball mill, but lower than in the single-particle mode of comminution under slow compressive loading. There is some evidence to suggest that the presence of water in feeds improves the energy efficiency of pressurised roll milling somewhat. Within a wide range of energy input, the size distributions of the ground product are self-similar, the logarithmic median size decreases linearly with the amount of fines produced and the inverse of the median size increases linearly with the energy spent. The production of fines as a function of energy expended follows essentially the same pattern as the one frequently encountered in media mills. The kinetics of grinding in the high-pressure roll mill can be simulated satisfactorily by modifying the standard particle population balance equation in order to account for energy dissipation in the tightly compressed bed. Common characteristics and important differences in grinding by the media mill and the high-pressure roll mill are highlighted.

Jan 1, 1993

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

The Mt Leyshon Gold Mine is located 30 kilometres south of Charters Towers in Northern Queensland. The current open cut mine has been in operation since 1986. In 1992 a feasibility study was completed that recommended an increase in production to over 240 000 ounces of gold per year. This proposal required an upgrade of the processing plant to five million tonnes per year, and an enlarged mining fleet to provide additional ore, and to meet the increased waste removal requirements. The implementation of the mine expansion program during 1993 required the Life of Mine plan to be extensively revised. This required the assessment and management of potential risks associated with the mine design. The updated geological model using the 1992 drilling results along with the actual contract mining and processing costs were used to establish a series of nested optimised pit shells. The total and incremental quantities and costs were then analysed to determine a suitable pit perimeter. The pit and phase plans were then created and used to devise a staged development plan. The block layout plans for each bench were then established from which a detailed life of mine production schedule was created.

Jan 1, 1994

This paper examines the operational characteristics and requirements of crushers and screens. Several possible control loops are considered and it is shown how these can be used to satisfy particular requirements.

Jan 1, 1978

Development of a small ore body to 137m below surface was carried out in sixteen months driving 610m of 1:5 decline.

Jan 1, 1973

At CPA we believe that ore bodies discovered in future will be bigger and higher grade than the ones currently known and set out targets accordingly. Discoveries over the last three decades substantiated this approach.

Jan 1, 1987

In Situ Bioremediation of a Heavily Polluted Alkaline Soil in a Uranium Deposit

Sep 13, 2010